Posted on

STMicro EVLDRIVE101-HPD 1.9-inch motor driver board can drive 750W BLDC motors

STMicroelectronics has recently revealed the reference design for “EVLDRIVE101-HPD” their homegrown BLDC motor driver board that can drive up to a 750W BLDC motor. This compact 50 mm (1.9-inch) circular PCB combines STDRIVE101 3-phase, triple half-bridge gate-driver IC with an STM32G0 microcontroller, which is responsible for driving three-phase brushless motors. The driver board supports various motor-control strategies, including trapezoidal and field-oriented control (FOC), with both sensor’ed and sensorless rotor-position detection. Additionally, it has a wide operating voltage range of 5.5V to 75V and includes STL220N6F7 60V STripFET F7 MOSFETs, which have very low Rds(on) for high efficiency. Other features of the board include ultra-low power consumption in sleep mode, a single-wire debug interface, direct firmware update capability, and protection mechanisms such as under-voltage lockout, overtemperature protection, and cross-conduction prevention. All these features make this board suitable for applications like hairdryers, handheld vacuums, power tools, fans, drones, robots, and industrial equipment […]

Posted on

LILYGO T-ETH-ELite ESP32-S3 Ethernet PoE board supports stackable LoRaWAN and Cellular expansion modules

LILYGO T-ETH-Elite is an ESP32-S3-powered IoT board with an Ethernet RJ45 port supporting PoE and a 40-pin GPIO header for stackable shields that offer support for LoRaWAN, 2G, NB-IoT, or/and 4G LTE cellular connectivity. The ESP32-S3 board allows users to build gateways with Ethernet, WiFi, Bluetooth, GNSS, LoRaWAN, and Cellular (2G, NB-IoT, 4G LTE) connectivity, and they can easily switch cellular modules to match specific requirements. LILYGO T-ETH-Elite specifications: Wireless module – Espressif ESP32-S3-WROOM-1 MCU – ESP32-S3R8 dual-core Tensilica LX7 up to 240 MHz with 512KB SRAM, up to 8MB PSRAM Storage – 16MB flash Connectivity – WiFi 4 and Bluetooth LE 5 PCB antenna Storage – MicroSD card slot Networking – 10/100Mbps Ethernet RJ45 port via W5500 SPI to Ethernet chip USB – USB Type-C port for power and programming Expansion – 40-pin (mostly) Raspberry Pi-compatible GPIO header for shields (up to 23x GPIO, USB 2.0, UART, 5V, 3.3V, […]

Khadas Edge2 Arm mini PC
Posted on

Quectel LG290P is the world’s first quad-band GNSS module (L1, L2, L5, and E6)

The Quectel LG290P is a quad-band, multi-constellation, high-precision, real-time kinematic (RTK) GNSS module that supports GPS, GLONASS, Galileo, BDS, QZSS, and NavIC constellations. A typical GNSS module like the SparkFun GNSS L1/L5 can receive signals from only one or two frequency bands, but the Quectel module can receive signals from four different frequency bands (L1, L2, L5, and E6) simultaneously and features built-in anti-jamming technology for improved signal reception in challenging environments. All these measures make this chip suitable for high-precision navigation applications like autonomous robots, UAVs, precision agriculture, surveying and mapping, and autonomous driving. Previously we have written about higher precision GPS modules like the SparkFun RTK EVK module, SparkFun RTK Torch module, the Cavli C17QS IoT GNSS module and much more feel free to check those out if you are interested in those topics. Quectel LG290P GNSS module specification Main module- LG290P GNSS Frequency bands and constellations GPS – L1 […]

Posted on

LattePanda Mu Intel N100 SoM and carrier board review – Part 2: Ubuntu 24.04

We’ve already checked out the hardware for LattePanda Mu and tested it on Windows 11 using both the Lite Carrier Board and Full-Function Evaluation in the first part of the review. We’ve now had time to test the LattePanda Mu Intel N100 board with Ubuntu 24.04 to see how it performs in Linux with the following tests:

Initial system information
Benchmarks for CPU, disks, peripherals, and networking (GbE and WiFi)
Web and multimedia usage
Power consumption

Since LattePanda Mu is an x86 machine, we can create a boot disk from the Ubuntu 24.04 ISO as we would on a PC.

Posted on

Jetway JMTX-ADN8 mini-ITX motherboard features Intel N97 CPU, dual GbE, three display interfaces

The Jetway JMTX-ADN8 is a mini-ITX motherboard built around an Intel N97 (Alder Lake-N) processor. The board supports up to 32GB DDR5 RAM via a single SO-DIMM slot and can drive up to three independent displays powered by Intel UHD graphics. Additionally, it offers dual GbE LAN, nine USB ports both USB3.2 Gen 1 and USB 2.0, and multiple storage and expansion options including M.2 (M-key, E-key, and B-key) and SATA-III. The motherboard also includes PCI expansion and supports Windows and Linux operating systems. In one of our last posts, we wrote about the Jetway JNUC-ADN1, another Intel N97-powered SBC, but in a smaller Next Unit of Computing (NUC) form factor. Other than that we have written about similar motherboards in mini-ITX from factors including Radxa ROCK 5 ITX, MW-100-NAS, and ASRock IMB-A8000 feel free to check those out if you are looking for mini-ITX motherboards. Jetway JMTX-ADN8 mini-ITX SBC […]

Posted on

Forlinx FET3576-C Rockchip RK3576 SoM powers feature-rich OK3576-C board for AIoT applications

Forlinx FET3576-C SoM is a new System-on-Module built around the Rockchip RK3576 SoC which features four Arm Cortex-A72 and four Cortex-A53 cores made from a 22nm lithography process. The SoM is available with 2GB or 4GB of LPDDR4 RAM option and can be equipped with up to 32GB of eMMC storage. Additionally, it has 6 TOPS NPU power and supports standard peripherals like GbE Ethernet, Wifi, Bluetooth, LVDS, MIPI DSI, and much more. All these features make this device useful for IoT, edge computing, digital signage, and many other applications. The new FET3576-C SoM and its OK3576-C development board look very similar to the Forlinx FET3562J-C SoM and related board we covered earlier this month. But the main difference between the two is that the new one is built with the RK3576 SoC whereas the old one is built around the Rockchip RK3562(J) SoC. Previously we also saw that the […]

Rockchip RK3568/RK3588 and Intel x86 SBCs
Posted on

Seeed Studio Wio Tracker 1110 Dev Kit supports Meshtastic for off-grid communication

The Seeed Studio Wio Tracker 1110 is a dev kit designed to work with the Meshtastic network. The board is built around a Nordic nRF52840 multiprotocol Bluetooth 5.4 SoC and uses the Semtech LR1110 LoRa transceiver for communication. Seeed Studio is selling the Wio Tracker 1110 development board in a bundle with an OLED display and a GNSS receiver, providing everything needed to start experimentation for peer-to-peer LoRa mesh networking. Meshtastic is a free, open-source, decentralized mesh network that uses LoRa radios to establish a low-power, long-range, off-grid communication system in areas without reliable infrastructure. Driven entirely by the community, Meshtastic enables decentralized, encrypted communication without the need for a dedicated router or phone. Previously we have written various versions of the Wio Tracker including the Wio GPS and Wio LTE GPS Tracker. Since Meshtastic projects are becoming popular among developers and enthusiasts, we will likely see many more dev […]

Posted on

ODrive Micro is a compact, brushless motor controller designed for space-constrained robotics applications (Crowdfunding)

ODrive Micro is a high-performance servo motor drive from ODrive Robotics that comes in an ultra-compact, 32 x 32mm form factor. The controller provides up to 100W continuous power for driving brushless servo motors. The ODrive Micro is the latest in a series of motor controllers from ODrive and builds on the company’s established software and hardware ecosystem. This includes support for CAN Bus, programming libraries, and a web-based graphic user interface for easy and intuitive setup. The Micro features a CAN interface for daisy-chaining other controllers and an onboard 12-bit magnetic encoder for direct mounting without needing an external encoder. It also offers the option to mount hall, quadrature, and SPI external encoders via the J1 header on the board. The ODrive Micro is aimed at robotics applications where space is premium, including hobbyist and professional use. It is similar to the Wukong 2040, ClearCore, and the Serial Bus […]

Khadas VIM4 SBC