Posted on by Debashis Das - No Comments on JUMPtec SMARC-sAM67 – An industrial SMARC SoM based on TI AM67x Jacinto SoC for Edge AI and vision applications

JUMPtec SMARC-sAM67 – An industrial SMARC SoM based on TI AM67x Jacinto SoC for Edge AI and vision applications

Jumptec SMARC sAM67 SoM

JUMPtec, a subsidiary of Kontron, has recently introduced SMARC-sAM67, an industrial SMARC SoM built around Texas Instruments’ AM67x Jacinto dual- or quad-core processors (AM67, AM67A, or AM67D) designed for industrial, robotic, and vision applications. The SMARC-sAM67 module features up to 8GB LPDDR4 memory, up to 64GB eMMC 5.1 flash, dual Gigabit Ethernet, PCIe Gen3 x1 expansion, USB 3.2 and USB 2.0, and display interfaces including dual-channel LVDS and DSI (or optional DisplayPort). It also features four UARTs, CAN bus, SPI, I2S, I2C, MIPI CSI cameras, and various industrial features such as extended temperature support (-40°C to 85°C), failsafe update support, and an ultra-low power RTC. JUMPtec SMARC-sAM67 SoM Specifications: SoC – Texas Instruments dual- or quad-core AM67x Jacinto processor (Standard AM67, optional AM67A or AM67D) System Memory – Up to 8GB LPDDR4 RAM Storage – Up to 64GB eMMC 5.1 flash storage Networking – 2x 10/100/1000 Mbps Ethernet PHY with […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on ESP-HDMI-Bridge is an ESP32-P4 HDMI streaming adapter with USB, Ethernet, WiFi, and microSD card

ESP-HDMI-Bridge is an ESP32-P4 HDMI streaming adapter with USB, Ethernet, WiFi, and microSD card

ESP32-P4 MIPI HDMI adapter

ESP-HDMI-Bridge is an ESP32-P4-based HDMI streaming adapter based on Lontium Semiconductors’s LT8912B MIPI-DSI to HDMI bridge chip outputting MIPI-DSI video signal of ESP32-P4 to HDMI devices. It allows the user to connect a computer to an HDMI display or projector through USB, Ethernet, or WiFi, or use it directly as a digital signage player or live dashboard connected to an HDMI display. The current solution is based on the ESP32-P4-Function-EV-Board connected via its MIPI DSI connector to a 50x40mm board with the LT8912B bridge, a MIPI DSI input connector, LVDS and HDMI video outputs, and a 12-pin header with I2C, I2S audio, etc., with everything housed in a plastic enclosure. The best is to watch the video below, which shows various demos: USB to HDMI up to 720p30 or 1080p15 Ethernet to HDMI WiFi to HDMI up to 1080p40 using the ESP32-C6 2.4 GHz WiFi 6 module on the ESP-P4 […]

ArmSoM RK3588 AIModule7 NVIDIA Jetson Nano-compatible SOM
Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on CM5-DUAL-ETH-MINI-BOX is a dual gigabit Ethernet router box for the Raspberry Pi CM5

CM5-DUAL-ETH-MINI-BOX is a dual gigabit Ethernet router box for the Raspberry Pi CM5

Raspberry Pi CM5 dual gigabit Ethernet router

Waveshare CM5-DUAL-ETH-MINI-BOX is a dual gigabit Ethernet router box designed for the Raspberry Pi CM5. It offers a familiar design with a metal enclosure that looks suspiciously similar to FriendlyELEC’s family of NanoPi routers powered by Rockchip processors, such as the NanoPi R2S Plus or NanoPi R3S. The router also features a microSD card slot to boot the OS on the Raspberry Pi CM5 Lite, a USB 3.0 Type-A port, a USB Type-C port for power and eMMC flash programming, power and boot buttons, and a 40-pin GPIO header accessible without opening the case (after lifting a cover). CM5-DUAL-ETH-MINI-BOX specifications: Supported SoMs – Raspberry Pi CM5 and CM5 Lite, and potentially compatible alternatives like the Raspberry Pi CM4,  Orange Pi CM5, Radxa CM5, etc… Networking 2x Gigabit Ethernet RJ45 ports: one GbE exposed directly through the CM5 board-to-board connector, and the other via a RealTek RTL8111H PCIe controller WiFi 5 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Openviro Axe PoE is an RP2040-based environmental sensor for server rooms and cabinets (Crowdfunding)

Openviro Axe PoE is an RP2040-based environmental sensor for server rooms and cabinets (Crowdfunding)

OPENVIRO Axe PoE

Openviro Axe PoE is a rack-mountable, open-source environmental sensor designed to measure the temperature and humidity (and air pressure) in server rooms or cabinets with electrical equipment. The device is based on a Raspberry Pi RP2040 board with Ethernet connectivity housed in an aluminum enclosure and equipped with two RJ12 connectors for Bosch BME280 sensors with an accuracy of +/- 0.5°C. It provides better results than sensors placed in a machine that may be impacted by the internal components’ heat dissipation. For instance, the two sensor inputs can be used to measure the temperature and humidity of the intake and exhaust in a server rack. Openviro Axe PoE specifications: Microcontroller – Raspberry Pi RP2040 dual Arm Cortex-M0+ @133 MHz with 264 KB SRAM Storage – 16 MB flash memory Network – 10/100Mbps Ethernet RJ45 port via LAN8710Ai Expansion – 2x RJ12 connector for THP Probes Misc – 3x Buttons Power […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Solar-powered WisMesh Repeaters extend the range of Meshtastic networks

Solar-powered WisMesh Repeaters extend the range of Meshtastic networks

Solar Powered WisMesh Meshtastic Repeaters

RAKWireless has launched two solar-powered Meshtastic range extenders/repeaters: the WisMesh Repeater with a larger battery and external solar panel, and the WisMesh Repeater Mini with a more compact design with an integrated solar panel Meshtastic open-source firmware allows LoRa nodes to be used for off-grid messaging, GPS coordinates sharing, and more. The mesh network relies on nodes to communicate with each other and relay messages to other nodes if needed. However, this does not work reliably when nodes are too far apart or one node goes offline for whatever reason. That’s when Meshtastic repeaters are needed. WisMesh Repeater / Repeater Mini specifications: WisBlock RAK4631 Core Module Wireless SoC – Nordic Semi nRF52840 Cortex-M4F MCU @ 64 MHz with 1MB flash, 256 KB RAM, BLE 5.0, pre-flashed with Meshtastic firmware LoRa transceiver – Semtech SX126x series with support for Meshtastic 8xx and 9xx MHz networks 800 MHz – RU864/ IN865/ EU868 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on ALPON X4 – A Raspberry Pi CM4 fanless Edge Computer with 4G LTE cellular connectivity

ALPON X4 – A Raspberry Pi CM4 fanless Edge Computer with 4G LTE cellular connectivity

ALPON X4

SixFab ALPON X4 is yet another fanless Raspberry Pi CM4-powered edge computer whose main selling point is built-in 4G LTE cellular connectivity with an eSIM, besides two Ethernet ports, and dual-band WiFi 5 and Bluetooth 5.0 on the system-on-module. The edge computer ships with 8GB RAM and 32GB eMMC flash by default, but another Raspberry Pi CM4 can be used upon request. Other ports include HDMI video output,  two USB 2.0 ports, and an RJ11 jack for GPIO expansion. The system supports three power options: USB PD, a 9V to 30V DC input terminal block, or PoE. ALPON X4 specifications: SoM – Raspberry Pi CM4 SoC – Broadcom BCM2711 CPU – Quad-core Cortex-A72 SoC @ 1.5GHz GPU – VideoCore VI with support for OpenGL ES 3.1 and Vulkan 1.0 VPU Decode – H.265/HEVC up to 4Kp60, H.264 up to 1080p60 Encode – H.264 up to 1080p30 Memory – 8GB LPDDR4-3200 […]

Rockchip RK3568, RK3588 and Intel x86 SBCs and SoMs in 2025
Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on HoneyComb Ryzen V3000 – An AMD Ryzen V3C18I mini-ITX motherboard with dual 10Gbps SFP+, 2.5GbE, dual SATA III

HoneyComb Ryzen V3000 – An AMD Ryzen V3C18I mini-ITX motherboard with dual 10Gbps SFP+, 2.5GbE, dual SATA III

HoneyComb Ryzen V3000

SolidRun HoneyComb Ryzen V3000 is a mini-ITX motherboard powered by an AMD Ryzen Embedded V3C18I processor, supporting up to 64GB of DDR5 memory and M.2 PCIe NVMe SSD storage, and equipped with two 10 Gbps Ethernet SFP+ cages, a 2.5GbE RJ45 jack, and two SATA III ports for advanced networking and storage applications. The solution is comprised of a mini-ITX motherboard and a Ryzen V3000 CX7 COM Express module, which the company introduced in 2022. As an industrial motherboard, it’s designed to operate in the -40°C to +85°C temperature range. HoneyComb Ryzen V3000 specifications: Ryzen V3000 CX7 COM Express module SoC – AMD Ryzen Embedded V3C18I octa-core/16-thread processor clocked at 1.9 GHz / 3.8 GHz (Turbo) with 4 MB L2 cache and 16 MB L3 cache; TDP: 15W System Memory – Up to 64GB (2x 32GB), ECC/Non-ECC DDR5 memory up to 4800 MT/s via two SODIMM sockets. Dimensions – 125 […]

Posted on by Debashis Das - 3 Comments on Thin PoE HAT for Raspberry Pi 5 features isolated SMPS, fits inside the official case, works with the active cooler

Thin PoE HAT for Raspberry Pi 5 features isolated SMPS, fits inside the official case, works with the active cooler

Waveshare PoE HAT (H)

Waveshare has launched the PoE HAT (H), a thin Power over Ethernet(PoE) HAT for the Raspberry Pi 5 that easily fits inside the official case and works with the active cooler. The HAT is specially designed for the Raspberry Pi 5 and supports IEEE 802.3af/at PoE standards. It features an isolated switched-mode power supply (SMPS) that delivers a stable 5V/5A output through the GPIO header.  The board includes a standard 40-pin GPIO header and relies on a low-profile PoE IC. Waveshare PoE HAT (H) Specifications: Compatibility – Raspberry Pi 5 Expansion – 40-pin Raspberry Pi GPIO header Cooling Fits inside the official Raspberry Pi 5 case Compatible with the official active cooler Misc – Onboard original IC for stable PoE performance Power Supply IEEE 802.3af/at compliant Isolated switched-mode power supply (SMPS) PoE power input – 37V to 57V DC Output via GPIO header – 5V, 5A (max) Dimensions – 65 x 56.5 […]

Boardcon CM3588 Rockchip RK3588 System-on-Module designed for AI and IoT applications