Hardware Category - Page 1086 of 1114 - CNX Software

June 22, 2012June 22, 2012 by Jean-Luc Aufranc (CNXSoft) - No Comments

VIA Announces ARM Cortex A9 Based Digital Signage System

VIA has unveiled its ARM Digital Signage (DS) system for cost sensitive high volume digital signage deployments. The system is based on an unnamed Cortex A9 processor (possibly Wondermedia WM8850?) with up to 2 GB RAM and 64 GB Flash. The company expects the device to be used in a wide range of applications such as kiosks, POS systems, video walls, menu boards to TVOIP, cloud streaming, and Out of Home Advertising. Here are the specs of this digital signage player: All in one system-ready to load software Designed for Android operating system Industry standard ARM Cortex A9 SoC Hardware acceleration of the most demanding video formats for resolutions up to 1080p DVI-D display port (HDMI Optional) 4x USB 2.0 ports 10/100 Ethernet port Audio-out/ Mic-in Up to 64GB NAND Flash Up to 2GB DDR3 SDRAM Dimension – 18 cm x 12 cm x 2.5 cm The VIA ARM DS […]

June 21, 2012 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Phoronix Designed a Solar Powered ARM Cluster with 48 Pandaboards

Michael Larabel of Phoronix did a “little” week-end project at the Massachusetts Institute of Technology (MIT), building an ARM cluster with 48 Pandaboards mostly with standard Pandaboards (OMAP 4430), although some Pandaboard ES (OMAP 4460) were also thrown in the mix. The 96-core cluster consumes just over 200 Watts under load and can be powered by a solar panel. The boards are stacked up vertically in an industrial trashcan, and are powered via USB instead of AC adapters. Michael’s PandaBoard ES testing indicates about a 3 Watt idle per board, 5 Watt under load, or 6 Watts under extreme load. The cluster idle power consumption is just under 170 Watts while idle, and goes slightly over 200 Watts under load. Each Pandaboard runs Ubuntu 12.04 ARM OMAP4 installed on SD cards. MIT did some testing and provided Phoronix with benchmark results such as tests following Green500 benchmarking procedure, but they are […]

June 19, 2012July 17, 2012 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

ARM vs x86 Servers Benchmark – Calxeda EnergyCore ECX-1000 vs Intel Xeon E3-1240

Calxeda has released the results of ApacheBench benchmark comparing their ARM-based EnergyCore solution to an Intel Xeon server in order to showcase the performance and the much lower power consumption of their servers. Here’s the setup: Hardware: Single Calxeda EnergyCore ECX-1000 @ 1.1 GHz, 4 GB of DDR3L-1066 memory, 1Gb Ethernet network port and 250 GB SATA 7200rpm HDD Intel Xeon E3-1240 @ 3.3 GHz, 16 GB memory and 1Gb Ethernet network port. No info on hard drive provided Software: Ubuntu Server v12.04 Apache Server v2.4.2 ApacheBench v2.3 (16k request size) They performed power measurements every 2 seconds and averaged the results. Power supply overhead and hard drive power consumption were not excluded in the measurement, but the entire SoC and DDR memory power consumption were included together. For the Intel server however, they could not measure directly, so they used published TDP values for the CPU (80 W) and I/O […]

June 18, 2012June 3, 2013 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Getting Started with Emcraft Systems Cortex M3/M4 Starter Kits Running uCLinux

A few months ago, I wrote a post about running uCLinux on Cortex M3/M4. Since then I’ve had the opportunity to play a with Cortex M3 & M4 boards capable of running Linux, as last week, I received Emcraft Systems Freescale K70 Starter Kit together with their MicroSemi (previously known as Actel) Smartfusion SoM. Today, I’ll show some pictures of the baseboard and modules I received in the kit, and some details about the documentation and how to get started with the modules. Unboxing Pictures Here’s the baseboard with Ethernet, USB interface using USB-UART bridge connected to the UART0, JTAG connectors (P3 and P5), two push-buttons and a breadboard for easy access to unused signals (ADC, I2C, SPI, UART and GPIOs). P4 and P6 are the sockets to plug in the SoM. There is a lithium-ion battery (CR2016) at the back of the board for the RTC clock. As previously […]

June 18, 2012May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

MK802 Android 4.0 mini PC Factory Video

Nicolas Charbonnier, better known as charbax, has shot yet another cool video in one of the small factories where MK802 is assembled, showing the different steps they follow to build a complete device. The PCB assembly is probably done in another factory, and they just assemble the device in this factory, or I should probably call it a workshop… The place appears to be rather small and everything is done by hand, but that’s what makes the video very interesting. This is the company that sells it on Amazon under the brand “OEM Systems Company”. The first five minutes shows a tour of the factory, and in the rest of the video, Charbax interviews the sales manager and the owner of the factory who both dodge sensitive questions about pricing, BOM costs and quantities manufactured monthly… But hey, you’ve got to try. Jean-Luc Aufranc (CNXSoft)Jean-Luc started CNX Software in 2010 […]

June 15, 2012May 25, 2014 by Jean-Luc Aufranc (CNXSoft) - 129 Comments

WM8850-MID Android 4.0 Tablet Unboxing and Review

I recently bought an Android 4.0 tablet with a 7″ capacitive touchscreen based on the new WonderMedia WM8850 processor (Cortex A9 + Mali-400). In my first post, I called this tablet UGoos UG-LMW70, but I just received a no brand package with nothing mentioning Ugoos or the model number UG-LMW70 anywhere. Android settings just show WW8850-mid for the model number. The tablet comes with a 5V power supply, a miniUSB to USB cable, a short miniUSB to USB female adapter, headphones and a user manual in English explaining how to use Android, but nothing about the tablet itself. The tablet has vol-/+ buttons and a power button (left side below), and a power jack, microSD slot, headphones jack, a USB host port, a mini HDMI port, a miniUSB port and a microphone (right to left). They did not include a mini HDMI to HDMI cable, so I did not try HDMI […]

June 14, 2012June 14, 2012 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Deeper Smart FishFinder: A Sonar For Android and iOS Mobile Devices

Friday Lab has designed and developed Deeper Smart Fishfinder, a Sonar that communicates with your smartphone or tablet via Bluetooth in order to help you locate the best location for fishing (i.e. where the fish are…). Deeper works with Android 2.2 or greater devices as well as iPhones and iPADs running iOS 4.0 or greater. The device, about the size of a tennis ball, is made of high-impact polycarbonate shell. This smart sonar is waterproof and can handle small shocks. You can use the Deeper for up to 6 hours on a battery charge and Bluetooth range is up to 50 meters. You’ll be able to see the bed of the pond, lake or river on your device, know where and how big the fish are as well as the temperature and depth of water. You can watch the video to see how the device was designed and how it […]