Hardware Category - Page 1075 of 1115 - CNX Software

November 5, 2012May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 19 Comments

$100 Mele A1000G / A2000G Android Media Players with 1GB RAM and 8GB Flash

I’ve been asked by several people when there would be a Mele with 1GB RAM, well the time is now, with the Mele A1000G and Mele A2000G. Both appear to be based on the previous Mele A1000 and Mele A2000 set-top boxes, but feature 1 GB RAM and 8 GB Flash instead of 512 MB RAM and 4 GB Flash. Here are Mele A1000G & Mele A2000G Specifications: SoC – AllWinner A10 Cortex A8 processor @ 1GHz System Memory – 1 GB DDR3 Storage: 8GB NAND Flash SD card slot (up to 32 GB) Connectivity: Wi-Fi – 802.11 b/g 10/100 MB Ethernet USB – 3 USB Host ports SATA Interface for 2.5″ HDD Video Output – HDMI, composite and VGA. Audio Output – RCA stereo output and optical out (SPDIF) Audio Formats – MP3 / WMA / WAV / OGG / FLAC / MKA Video Formats – TS / M2TS […]

November 5, 2012May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

PengPod 700 & 1000 – Linux Tablets Based on AllWinner A10

There are plenty of tablet based on AllWinner A10 and A13 processors, but all of them run Android, and you are out of luck if you want to run Linux on your tablet, unless you hack this yourself. But this is about to change as PengPod will launch 2 tablets and 1 mini PC running Linux from NAND flash or micro SD card: PengPod 700 – 7″ tablet with Allwinner A10, 1GB RAM and 8GB Flash PengPod 1000 – 10″ tablet with AllWinner A10, 1GB RAM and 8GB Flash PengStick – AllWinner A10 mini PC with 1GB RAM and 4 GB Flash The table below gives more detailed specifications and comparison of the three devices. Device PengPod1000 PengPod700 PengStick Type Tablet Tablet TV Stick CPU Allwinner A10 AllWinner A10 AllWinner A10 Android 4 4 4 Linux 3.0.42 3.0.42 3.0.42 Screen 10” 7” External Resolution 1024×600 800×480 1080i Ram 1GB 1GB […]

November 3, 2012November 3, 2012 by Jean-Luc Aufranc (CNXSoft) - 24 Comments

Rockchip RK3066 UG802 mini PC is Now Available for Just $46.50

Earlier today, a reader left a comment about a mini PC based on RK2908 sold for $40 including shipping on Ebay. No bad! But since I hadn’t checked mini PCs on Aliexpress for a few months, I decided to have a look for cheap devices. The cheapest sold by a company with decent feedback is the IP872 ($34 including shipping), but it’s based on an ARM11 chip (Infotmic IMAPX 200) and runs Android 2.3, so I don’t find it that interesting. There are also some AllWinner A10 mini PCs that cost just above $40 including shipping, but then I found one company selling UG802 for $46.50 including shipping via China Post. It’s quite shocking that the price halved within 3 months, and this makes single core mini PC that less attractive, unless you want to run Linux (Ubuntu, Debian…) which is not yet supported by RK3066. The device sold by […]

November 2, 2012November 2, 2012 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Versatile Express TC2 (2xA15, 3xA7) Development Board at ARM Techcon 2012

If you’ve been following Linaro work, you may have read they develop big.LITTLE processing on TC2, a Test Chip based on 2 Cortex A15 cores and 3 Cortex A7 cores. Charbax is at ARM Techcon 2012 and he shot an interesting video showing 2 Versatile Express development boards based on TC2 demonstrate different big.LITTLE processing schedule strategies: The first scheduling strategy switches between Cortex A15 and Cortex A7 depending on the load required. The second scheduling strategy makes use of 5 cores at the same time and runs high load tasks on the Cortex A15 cores whereas simpler tasks are run on Cortex A7 core. This is only available on Android and Linux and the moment. TC2 is an actual silicon (not FPGA), and as they opened the casing of the development kit (Around 5:00 in the video), you’ll see a fan to cool down the SoC as it is […]

November 2, 2012November 2, 2012 by Jean-Luc Aufranc (CNXSoft) - No Comments

199 Euros “Energy Harvesting Solution To Go” Kit with Energy Micro Cortex M3 Starter Kit

If you’re interesting in battery less ultra low power applications, Energy Micro, Linear Technology and Würth Elektronik have announced an energy harvesting development platform early last month. The “Energy Harvesting Solution To Go” Kit is composed of an Energy Micro Giant Gecko (Cortex M3) Starter Kit and an energy harvesting board that is capable of getting enough solar, thermal, piezoelectric or electromagnetic energy to power the MCU board. The power connector shown above connects directly to the Giant Gecko Starter Kit board to provide power. Although there are 4 energy harvesters on the board, only one power source can be selected at a time via jumpers. Several power sources can be selected by using diodes. The board The energy harvesting board offers two integrated energy sources: A solar cell (32mm x 50mm) A thermo-generator (40mm x 40mm). And 2 other external energy sources can be added to the board via […]

November 1, 2012 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

The Beaglebord Community Launches The Beaglebone Cape Design Contest

The Beagleboard community has just announced the BeagleBone Cape Plug-in Board Design Contest. All you need to do (more easily said than done) is to design a Capefor the Beaglebone and submit the relevant materials during the contest period (November 1 – December 31, 2012) and if you’re one of the winner, you’ll receive cash prizes, a free devkit and you’ll become a Beagleboard community “God” as your Cape will be manufactured and sold through CircuitCo Electronics. To enter the competition, you’ll need to do the following by the 31st of December 2012: Come up with an original cape design and upload the Schematic layout and Bill of Materials (>$60) to an online sharing site (ex: Google Drive, Github) set for public view. Record a video describing your cape idea and upload it to YouTube. Click on the Submit Design Here button in http://beagleboard.org/CapeContest/ to submit your entry. On January 7, 2013, the list […]

November 1, 2012 by Jean-Luc Aufranc (CNXSoft) - No Comments

OLPC XO-4 Touch Laptop Powered by Marvell ARMADA PXA2128

Last year, OLPC (One Laptop Per Child) announced their first laptop powered by ARM, with OLPC X-1.75 powered by Marvell ARMADA 610 single core processor (And sold over 100,000 since Q1 2012). The 2 new models – OLPC XO-4 and OLPC XO-4 Touch – will be upgraded to ARMADA PXA2128 triple core processor (2 ARMv7 Core + 1 Hybrid LPM (Low Power Mode) ARMv7 core), which the OLPC XO-4 Touch offering multitouch support. OLPC XO-4 laptop will look exactly like the OLPC 1.75 laptop pictured below. OLPC XO-4 will have the following specifications: SoC – Marvell PXA2128 (ARMv7 compatible) @ 1 GHz with Vivante GC2000 GPU System memory – 1GB or 2GB DDR3 RAM (Depending on configuration) Mass storage: 4 GB or 8GB NAND flash (eMMC) Internal microSD card slot for repair/replacement Externally accessible SD card slot; Display – 7.5” dual-mode TFT display with touchscreen (2 simultaneous touch max) Audio […]

November 1, 2012November 1, 2012 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

$149 Hardkernel ODroid-X2 Development Board with Exynos 4412 @ 1.7 GHz and 2 GB RAM

You’ve probably heard about the ODROID-X development board announced in July by Hardkernel. They now have an updated version called ODroid-X2 with Samsung Exynos 4412 clocked at 1.7 GHz (vs 1.4 GHz) and 2 GB RAM (vs 1 GB RAM for the first version). They also boosted the Mali 400 clock speed from 400 MHz to 533 MHz. Apart from being a good mobile development platform, the 2 GB RAM could make the board a pretty good native ARM build machine under Ubuntu, as I’ve read 1 GB RAM is not always enough at link stage (e.g. for Debian packages, sorry I can’t find the link), unless you use swap which tremendously slows things down. The rest of the board seems identical and it just looks the same as the first version. Charbax shot a video of Hardkernel ODroid-X2 development board at ARM Techcon 2012: ODroid-X2 will cost $149 (ODroid-X […]