zigbee

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Soap is a Touchscreen Enabled Router Supporting Gigabit Ethernet and Lots of Wireless Standards (Crowdfunding)

Soap is a Touchscreen Enabled Router Supporting Gigabit Ethernet and Lots of Wireless Standards (Crowdfunding)

Soap is a strange creature, and I’m not convinced there are that many use cases for such hardware, but I find it interesting that the developers decided to pack a Freescale i.MX6 Solo/Dual or Quad SoC powered Android 4.4 tablet and a router supporting five Gigabit Etherner ports, as well as WiFI 802.11ac, Wi-0Fi 802.11 b/g/n,  Zigbee, Z-wave, Bluetooth 4.0 (BLE), Insteon RF, X10, 433Mhz, NFC, and infrared into one and only device which they call an “Intelligent Home Management Hub”.  It’s also complete with an HDMI output port so that you can use it as a media player. Let’s go through the specifications for the four version this little monster (Soap Solo, Soap Dual, Soap Quad, and Soap 8.4): SoC Soap Solo – Freescale i.MX6 Solo single ARM Cortex A9 @ 1 GHz with Vivante GC880 3D GPU Soap Dual – Freescale i.MX6 Dual dual ARM Cortex A9 @ […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Texas Instruments Releases Zigbee Home Automation Gateway Reference Design Based on BeagleBone Black

Texas Instruments Releases Zigbee Home Automation Gateway Reference Design Based on BeagleBone Black

Texas Instruments has recently release a complete Linux based Zigbee home automation gateway based on BeagleBone Black development and CC2531 Evaluation Module Kit hardware which you can purchase for about $100 in total, and including Z-STACK Ubuntu gateway installer, as well as Z-STACK Home, a ZigBee Home Automation (ZHA 1.2) compliant protocol stack for the company’s CC2530 and CC2538 SoCs. I won’t go into details about the BeagleBone Black as I have already covered it into details previously. However, the hardware has slightly changed since the initial release, as the 2GB eMMC has now been replaced by a 4GB eMMC, and price has been increased to about $55. CC2531 evaluation module kit is comprised of CC2531 USB Dongle which you can connect to the USB port of a PC, or in this case a BeagleBone Black, for 802.15.4 / ZigBee applications. TI also provides CC2531 USB Firmware Library on their site to let developers […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on Atmel Introduces ARM Cortex M0+ based SmartConnect Wi-Fi Modules and SmartConnect Zigbee SoCs

Atmel Introduces ARM Cortex M0+ based SmartConnect Wi-Fi Modules and SmartConnect Zigbee SoCs

In order for the Internet of Things to take off, wireless connectivity solutions with ultra low power, lost cost, and small footprint are needed. Atmel seems to have made a step in the right direction by launching SmartConnect Wi-Fi modules and Zigbee SoCs featuring an ARM Cortex M0+ core. SmartConnect Wi-Fi does not appear to be a single chip solution, but instead Atmel has created a family of Wi-Fi modules integrating the company’s ultra-low power Wi-Fi SoChip with an ARM Cortex M0+ based MCU. These modules will enabled battery-powered Wi-Fi connectivity for IoT endpoints such as thermostats, and temperature sensors in a cost effective way. The company will provide a software solution with application and security protocols such as TLS, TCP/IP stack and an RTOS, all of which can be downloaded via Atmel Studio 6 Integrated Development Platform (IDP). SmartConnect ZigBee SAM R21 combines an ARM Cortex M0+ core with […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 7 Comments on Ninja Sphere Home Automation and Monitoring Platform

Ninja Sphere Home Automation and Monitoring Platform

Ninja Blocks is an company providing open source hardware solutions for home automation. Their first product was called Ninja Blocks Kit which includes a Ninja Block (Beaglebone + Arduino based gateway, but they now also support the Raspberry Pi), sensors, sockets, cables, and a power supply, and works with Ninja Platform, an open source software framework. The goal was to simplify the process of developing automation applications by taking care of all low levels tasks such as electronics, embedded programming, network protocols.., and letting “end users” / developers focus on their application. The company is now working on a new version called the Ninja Sphere, including a “Spheramid” gateway, location waypoints (Bluetooth low energy tags), and smart power sockets. Here are the key features of the gateway: Processor – ARM Cortex A8 (probably Texas Instruments Sitara) Color LED Matrix Connectivity – Bluetooth, Bluetooth LE, Zigbee, and Wi-Fi USB Port – […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Wireless Networking with IEEE 802.15.4 and 6LoWPAN – ELCE 2012

Wireless Networking with IEEE 802.15.4 and 6LoWPAN – ELCE 2012

Alan Ott, founder of Signal 11 Software, gives a presentation dealing with wireless networking for the internet of things in Linux, especially with 802.15.4 and 6LoWPAN standards at the Embedded Linux Conference in Barcelona, Spain on November 5, 2012. Abstract: With the rise of the internet of things, low-power wireless devices will become increasingly prevalent. IEEE 802.15.4 is a wireless networking protocol designed for low-power and low-data-rate devices, such as those used in wireless sensor networks. While some higher layer protocols based on 802.15.4 are proprietary, an open standard called 6LoWPAN enables IPv6 traffic over 802.15.4. This presentation will give overviews of 802.15.4, its status in the Linux kernel, hardware support, comparison with other wireless protocols, and a demonstration of a simple 802.15.4/6loWPAN network. This presentation is targeted toward developers who wish to create low-power, low-data-rate wireless networks for sensors or other applications. Attendees can expect to gain a basic […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Digi Launches XBee Modules Examples Website To Get Started with IoT Development

Digi Launches XBee Modules Examples Website To Get Started with IoT Development

Digi International has launches an example section on their website to showcase what can be done with their XBee 805.15.4, ZigBee and WiFi Modules, as well as their IoT gateway. They provide examples to use different type of sensors, control lights, motors, and more. They show demos on the website and explain how each components can be linked together, hooked to computers and connected to the internet. They currently just have a few tutorials only, but plan to add more overtime: Basic XBee 802.15.4 & Zigbee Chat 802.15.4 PWM and Digital Output with an LED 802.15.4 Digital Input with a Button 802.15.4 Analog Input with a Potentiometer Light Switch XBee – A wireless wall switch that can control lamps, fans, motors or your homemade robot The first four examples look good to get started, but the Light Switch XBee is the most interesting, and they describe 8 steps to show […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Freescale Announces Kinetis KW20 Cortex M4 MCU with Built-in Zigbee Transceiver

Freescale Announces Kinetis KW20 Cortex M4 MCU with Built-in Zigbee Transceiver

Freescale announced the addition of the Kinetis KW20 to its Kinetis microcontroller portfolio. The Kinetis KW20 is based on ARMCortex-M4 core and MC13242 RF transceiver to deliver a single chip Zigbee solution for the Internet of Things and power applications such as smart energy, smart metering and building control. The company explains that their new wireless MCU family aims to “address the increased processing and memory requirements associated with future ZigBee Smart Energy 2.0 and Internet Protocol specifications”. The KW20 supports dual personal area network (PAN) to enable a single device to communicate wirelessly on two ZigBee networks. This feature eliminates the need for multiple radios required to connect different home automation and smart energy networks. Kinetis KW20 wireless MCU features: ARM Cortex-M4 processor core Up to 512 KB of flash memory and 64 KB of RAM Cryptology accelerator and sophisticated tamper detect Integrated IEEE 802.15.4-compliant radio (MC13242 RF transceiver) Low […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on ConnectPort X2e SEP 2.0 Compliant Home Energy Gateway with Zigbee Connectivity

ConnectPort X2e SEP 2.0 Compliant Home Energy Gateway with Zigbee Connectivity

Digi International announced the “ConnectPort X2e for Smart Energy”, a Linux-based Home Energy Gateway with Zigbee connectivity based on Freescale Home Energy Gateway Reference Platform powered by Freescale i.MX28 processor. The “ConnectPort X2e for Smart Energy” is upgradable to comply with the new Smart Energy 2.0 Profile (SEP 2.0)  and  enables ZigBee devices on a Home Area Network (HAN) to communicate with an energy service provider. The new gateway is a low-cost, enhanced version (hence the “e” in X2e)  of Digi’s ZigBee Smart Energy Gateways.  The device connects ZigBee Smart Energy devices from a Home Area Network (HAN) to an energy service provider via broadband. It supports over-the-air updates of connected Smart Energy devices, making it easier for utilities and application partners to establish and maintain large Smart Energy device deployments. The company offers two models namely: ConnectPort X2e, ZigBee SE Coordinator for stand-alone Smart Energy networks that do not […]

UP 7000 x86 SBC