wifi News - Page 82 of 110 - CNX Software

September 12, 2016September 12, 2016 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

Pine64 Unveils $2 PADI IoT Stamp WiFi IoT Module with FreeRTOS SDK, Upcoming ARM mbed 5.0 Support

Realtek RTL8710 WiFi IoT modules came out as potential competitors to ESP8266 modules last month, with similar features. an ARM Cortex M3, and a pricing as low as $2 in quantities. However, documentation is often in Chinese only, and based on my experience with an RTL8710AF module limited to AT commands set for now. Software and documentation are likely to improve a lot however, as Pine64, the makers of Pine A64 boards, are about to launch their own “PADI IoT Stamp” RTL8710AF module for just $1.99 in any quantities. PADI IoT Stamp specifications: SoC – Realtek RTL8710AF ARM Cortex-M3 @ 83 MHz with 1MB ROM, 512KB RAM, and 1MB flash Connectivity – 802.11 b/g/n WiFi @ 2.4 GHz – 2.5 GHz (2400 MHz – 2483.5 MHz) with PCB antenna; Station / SoftAP / SoftAP + Station modes; Expansion headers – 22 half-holes with Up to 1x SPI @ 41.5 Mbps […]

September 5, 2016September 6, 2016 by Jean-Luc Aufranc (CNXSoft) - 28 Comments

You Can Now Buy ESP3212 ESP32 WiFi + Bluetooth Module for $6.95

After the official launch of ESP32 processor for less than $3, it did not take long before ESP32 modules hit the market, and Seeed Studio has already listed ESP3212, one of the first modules based on Espressif ESP32 Bluetooth LE + WiFi SoC, for $6.95 with shipping scheduled to start on September 23, 2016. ESP3212 module specifications: SoC – Espressif ESP32 dual core Xtensa LX6 processor @ up to 240 MHz with 448 KB flash, 520 KB SRAM, 16 KB SRAM in RTC, WiFi and Bluetooth LE connectivity Storage – 4MB Winbond SPI flash Connectivity 802.11 b/g/n/e/i WiFi (HT40) up to 150 Mbps Bluetooth 4.2 BR/EDR and BLE 3 dBi PCB antenna Headers – 22x GPIOs (multiplexed with ADC, Touch, DAC, SPI, UART, CAN, ETH, IR, PWM, and I2S), 1x UART, Sense VP/Sense VN, EN pin. 3.3V and GND Power Supply – 3.0 – 3.6V Dimensions – 24 x 16 […]

September 2, 2016September 3, 2016 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

Espressif ESP32 WiFi & Bluetooth SoC is Now Up For Sale for $2.85

Espressif ESP32 is one of the most awaited chip for IoT applications as it combines a dual core processor, WiFi, Bluetooth 4.0, and various I/Os. The good news is that you can now purchase ESP32 for 19 RMB ($2.85) on Taobao, or if you are not based in China, contact Espressif by email at sales [at] espressif.com. Availability is however limited, and the maximum order is now 5 pieces. ESP32 modules and boards, as opposed to just the SoC, are not quite ready right now, but should become available in a few weeks. ESP-WROOM-32 is the ESP32 module developed by Espressif, and NodeMCU is also working on an ESP32 board, so we’ll get more good news very soon. You can also find documentation, hardware and software resources on a Espressif ESP32 page , including a getting started guide, ESP32 SDK, ESP32 reference manual, ESP-WROOM-32 datasheet, and more. If you are […]

August 29, 2016August 29, 2016 by Jean-Luc Aufranc (CNXSoft) - 21 Comments

Broadlink MP1 is a $20 WiFi Power Strip with 4 Independent Sockets

There are plenty of WiFi sockets going around such as Broadlink SP2 or Kankun KK-SP3, but in some cases it might be both more convenient and cheaper to get a WiFi power strip, and Broadlink MP1 offers just that with 4 sockets that can be controlled and programmed (timer) independently, and sold for just $19.88 on Banggood. Broadlink MP1 specifications: Connectivity – 802.11b/g/n WiFi, controllable over 3G/4G with smartphone 4 multi-standard (EU/US/AU, but not UK) sockets Power input – 10A/250V (max) Power output – 10A/250V (max) Rated power – 2000W Total Misc – Power button Dimensions – 254mm x 60mm x 32mm; 50cm sockets spacing; cord Length – 1.5m with AU plug (Adapter provided for other countries) Weight – 450g The power strip can be controlled via Broadlink ihc (Intelligent Hone Control) app available for Android and iOS, which lets you independently manually turn on or off or set timers […]

August 24, 2016August 27, 2016 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

ReSpeaker WiFi IoT Board is Designed for Voice Interaction (Crowdfunding)

More and more devices are supporting voice interaction nowadays from your smartphone to devices like Amazon Echo, but so far, I had not seen development boards specifically designed for that purpose, and that’s exactly what Seeed Studio ReSpeaker board does by combining audio capabilities, WiFi connectivity, and I/O headers. ReSpeaker Core board specifications: WiFi Module – Acsip AI7688 Wi-Fi 802.11 b/g/n module based on Mediatek MT7688 MIPS SoC Storage – micro SD card slot USB – 1x micro USB port for programming and power Audio – 3.5mm AUX port, WM8960 audio codec, 2-pin header for external speakers Expansion – 2x 8-pin expansion headers for I2C, GPIO and USB 2.0 host connected to MT7688, built-in microphone. MCU – Atmel ATMega32U4 @ 16 MHz Misc – 12x RGB LEDs, 8x touch sensors, 3 push buttons Power Supply – 5V DC Dimensions – 70mm diameter Weight – 70 grams The board runs OpenWrt, […]

August 20, 2016August 22, 2016 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

Realtek RTL8710 Witty-like WiFi IoT Board with micro USB Port Sells for $8 / 35 RMB

Realtek RTL8710 could eventually become a serious competitor to ESP8266, as it’s based on ARM Cortex M3, provides many of the same features, and sells for roughly the same price. While currently software support is still work in progress and community is very small, I’ve recently written a quick start guide using AT commands to control RTL8710 connectivity in station and access point mode, and commands are also available for GPIO, OTA firmware updates, servers… This however requires some soldering and a USB to TTL debug board, and is not quite as convenient as ESP8266 board like NodeMCU. Some RTL8710 and RTL8195 development boards are already available but they cost over $25, but I’ve been informed of a cheap no-name RTL8710 board with a micro USB port for programming and power, and well as headers with GPIOs, UARTs, NFC, and power pins, that looks somewhat similar to ESP8266 Witty board. […]

August 18, 2016November 26, 2016 by Jean-Luc Aufranc (CNXSoft) - 18 Comments

Getting Started with B&T RTL-00 RTL8710 Module – Serial Console, AT Commands, and ESP8266 Pin-to-Pin Compatibility

The announcement of the ultra-low cost ARM based Realtek RTL8710 WiFi modules for IoT applications generated quite a lot of buzz since they can potentially compete with the popular ESP8266 modules. The main problem at the time was documentation and software support, but after some searches we could find that RTL8710 was part of Realtek Ameba family, and found some documents and an SDK for RTL8710/RTL8711/RTL8195. ICStation also kindly provided one B&T RTL-00 module for review, which costs $3.55 shipped per unit, and as low as $2.85 if you purchase 10 or more. The question here is how to get started? The answer can be found in page 8 of the Chinese datasheet for the module with GB0 and GB1 pins used for Tx and Rx to access the serial console. Time for some soldering… For the first test, we’ll just need Tx (GB1), Rx (GB0), GND and 3.3V, and […]

August 14, 2016August 14, 2016 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

GOLE1 mini PC Tablet Review – Part 2: Android 5.1 and Windows 10

GOLE1, also called GOLE1 F1, is an interesting device because it’s quite difficult, it’s like the offspring of a mini PC and a tablet with a smallish phone-like 5″ capacitive touch screen. It also dual boot Windows 10 and Android 5.1. I’ve already discussed about the hardware, and taken picture of the device, accessories, and motherboard, in the first part of the review, so today I’ll report my experiences with Windows 10 and Android 5.1, as well as the potential use cases. Since I’ve already reviewed Intel Atom x5-Z8300 mini PCs, as well as a dual boot Windows and Android Intel mini PC, I’ll focus on what makes GOLE1 different in this review. GOLE1 Dual Boot and Use Cases I normally check my emails on my smartphone while having breakfast in the morning, but one day the charging micro USB cable was not connected properly to my phone, so I […]