KWS-302WF is an inexpensive WiFi power meter with a color display and power control that is suitable for the whole house since it can handle up to 63A/17kW and supports DIN Rail mounting in a fuse box or cabinet. Installation is made through the neutral and live wires, and the display shows voltage, current, power, energy consumption, power factor, frequency, and temperature through an external temperature probe. Multiple KWS-302WF can be monitored and controlled through a mobile app which may make suitable suitable for apartment buildings as well. KWS-302WF specifications: Voltage range – 170-270V Current range – 0 to 63A Power range – 0 to 17 kW Energy range – 0 to 9999 kWh Timer range – 0 to 999 hours Temperature Range – -20 to +150°C (that is for the temperature sensor, and not the actual operating temperature range…) Frequency Range – 50 to 60 Hz Power Factor – […]
Theengs Bridge BLE to MQTT gateway supports Home Assistant, OpenHAB, Jeedom, NodeRed, and more
The Theengs Bridge is a new WiFi & Ethernet BLE to MQTT gateway running the open-source OpenMQTTGateway firmware, compatible with a range of sensors, and supporting Home Assistant, OpenHAB, Jeedom, NodeRed, and other MQTT-compatible systems. It follows the Theengs Plug smart socket introduced at the beginning of the board with many of the same features (minus the socket part…) but adds Ethernet and an external antenna for improved range, and improves modularity with a Grove I2C connector and mounting holes for a LoRa-E5-based Grove module and a prototyping area where you can solder your own circuitry with DIP components. Theengs Bridge specifications: Wireless module MCU – ESP32 microcontroller with WiFi and Bluetooth Storage – 8MB flash PCB antenna and u.FL antenna connector Connectivity 10/100M Ethernet RJ45 port 2.4 GHz WiFi 4 and Bluetooth LE with 6dBi 50Ohm external antenna Optional LoRa module via Grove I2C connector MQTT protocol Expansion – […]
Giveaway Week 2023 winners announced!
CNX Software’s Giveaway Week 2023 is now over and we’re ready to announce the winners. We offered some of the review samples we tested (or not) in the last year, and like the last two years, we were also joined by RAKwireless who offered two IoT development kits. All items given away are shown in the photo below, minus some accessories, and if you count more than seven you’d be right, as some are kits with multiple items like the GL.iNet GL-S200 Thread Border router which comes with three development boards, and more importantly, we also organized Giveaway Week on CNX Software Thailand for the second year running. We had seven winners on CNX Software: VOIPAC iMX8M industrial development kit – Kraingsak, Thailand TBS7901 mini PCIe DVB-S2X/S2 module – Frank, Singapore RAKWireless WisBlock IoT Starter Kit – Andy, Russia GL.iNet GL-S200 Thread Border router kit – Augustin, Argentina WCH CH583M-R0-1v1 […]
u-blox MAYA-W3 industrial wireless module supports WiFi 6/6E and Bluetooth 5.4 with LE Audio
We’ve already covered two IoT-focused WiFi 6 and Bluetooth LE chips last week with Synaptics SYN43711 chipset and Gigadevice GD32VW553 RISC-V WiSoC, but there’s more, and u-blox has recently introduced the MAYA-W3 WiFi 6/6E and Bluetooth 5.4 module with LE Audio support and designed for industrial applications. It follows the MAYA-W2 industrial IoT module with NXP iW611/iW612 SoC introduced last year. The MAYA-W3 module offers some flexibility as it’s designed on the upcoming Infineon AIROC CYW5551x WiFi 6E and Bluetooth 5.4 chip family supporting 2.4 GHz only (CYW55511), 2.4 GHz and 5 GHz (CYW55512), and a 2.4 GHz, 5 GHz, and 6 GHz with the tri-band CYW55512 chipset. u-blox also provides three antenna options for each model with two U.FL connectors, two antenna pin connectors, or an embedded PCB antenna. u-Blox MAYA-W3 specifications: Chipset – Infineon AIROC CYW5551x CYW55511 for 2.4 GHz WiFi 6 CYW55512 for 2.4 and 5 GHz […]
Linux-based DIN Rail smart controller works with Zigbee, Z-Wave, KNX, and Ajax Systems security solutions
CONNECT Y1 Smart Controller in a DIN Rail gateway running Ubuntu Linux and acting as the main control of YoctoCONNECT’s Smart Home/Smart Building solution with YoctoBus (RS485) and Ethernet interfaces, support for expansion blocks, and third-party integration with Zigbee, Z-Wave, KNX, and Ajax Systems security and smart home solutions. The Y1 Smart Controller handles automation algorithms and RS485, Ethernet, and USB communication for automated control systems for lighting, power distribution equipment, ventilation systems, climate control, and other electrical loads in various sectors such as Industry 4.0, Smart Homes, and Smart Cities. CONNECT Y1 Smart Controller specifications: SoC – Quad-core processor @ 1.2 to 2.4 GHz System Memory – 512MB, 1GB, or 2GB DDR3 RAM Storage – 16GB or 32 GB eMMC flash Audio – 3.5mm audio output jack; AirPlay support Connectivity YoctoBUS (RS485) interface via 3-pole terminal block 10/100M Ethernet RJ45 port USB 2.0 interface for Z-Wave or Zigbee Ajax […]
Gigadevice GD32VW553 RISC-V microcontroller supports WiFi 6 and Bluetooth 5.2 LE
Gigadevice GD32VW553 is a new 160MHz RISC-V microcontroller for IoT applications with support for WiFi 6 (802.11ax) and Bluetooth 5.2 Low Energy (LE) and available in QFN32 and QFN40 packages with up to 28 GPIOs. As an IoT chip, the chip supports various power modes and target wake time (TWT) for low power consumption, as well as WiFi features such as WPA3 and WiFi direct, while the radio can handle Bluetooth 5.2 LE bit rates of up to 2 Mbps and support the Long Range mode. Gigadevice GD32VW553 specifications: MCU core – 32-bit Nuclei N307 RISC-V core @ up to 160 MHz with RV32I / M / A / F / D / C / P / B instruction extensions Memory – 320KB SRAM Storage – 2048KB or 4096KB flash Wireless WiFI 6 802.11b/g/n/ax HT20 up to 114.7Mbps 802.11e QoS Enhancement (WMM). 802.11i (WPA, WPA2, WPA3). Open, shared key, and […]
Review of RaZberry 7 Pro Z-Wave Raspberry Pi HAT and Z-Uno2 Z-Wave board
Z-Wave.Me has sent us a couple of Smart Home devices based on Z-Wave technology for review, namely the RaZberry 7 Pro Raspberry Pi HAT and the Z-Uno2 board. The Swiss company has primarily developed Z-Wave products for years and is a member of the Z-Wave Alliance. For those who are concerned about the issues of signal interference in the 2.4GHz range (WiFi, Zigbee, Bluetooth, and Thread), Z-Wave technology is an excellent choice because it operates on a less congested frequency range of 800-900MHz and the technology has been around for more than 20 years, resulting in a wide variety of Z-Wave devices available in the market, and they can work well together across different brands due to a proper certification process which is another advantage when compared to other protocols. The two devices we received are RaZberry 7 Pro, which is a shield that plugs into the 40-pin GPIO header […]
SONOFF SNZB-06P Zigbee human presence sensor is based on a 5.8GHz microwave radar
ITEAD has launched a new Zigbee sensor with the SONOFF SNZB-06P designed to detect human presence using a 5.8GHz microwave radar whose main advantage over a traditional PIR motion sensor is the ability to detect stationary persons since this type of sensor can detect breathing. You’ll need a Zigbee Hub from SONOFF such as the NSPanel Pro or SONOFF iHost, or from other manufacturers, for instance, the Amazon Echo Plus 2nd generation, or simply use a Zigbee USB dongle such as the SONOFF ZBDongle-E connected to a host like a Raspberry Pi. Configuration and control is done through the usual eWelink app for Android or iOS. SONOFF SNZB-06P specifications: MCU – Silicon Labs EFR32MG22 wireless microcontroller Human presence sensor 5.8GHz microwave radar Sensitivity configurable from 2.5 meters to 4 meters Wireless – Zigbee 3.0 (router type) up to 30 meters Misc – Red LED, magnetic base, button Power Supply – […]