seeed studio News - Page 5 of 17 - CNX Software

August 2, 2022August 2, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

reComputer J101/J202 carrier boards are designed for Jetson Nano/NX/TX2 NX SoM

Seeed Studio’s reComputer J101 & J202 are carrier boards with a similar form factor as the ones found in NVIDIA Jetson Nano and Jetson Xavier NX developer kits, but with a slightly different feature set. The reComputer J101 notably features different USB Type-A/Type-C ports, a microSD card, takes power from a USB Type-C port, and drops the DisplayPort connector, while the reComputer J201 board replaces the micro USB device port with a USB Type-C port, adds a CAN Bus interface, and switches to 12V power input instead of 19V. The table below summarizes the features and differences between the Jetson Nano devkit (B1), reComputer J101, Jetson Xavier NX devkit, and reComputer J202. Note the official Jetson board should also support production SoM with eMMC flash, but they do ship with a non-production SoM with a built-in MicroSD card socket instead. The carrier boards are so similar that if NVIDIA would […]

July 8, 2022July 8, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Seeed Studio outs $5 XIAO ESP32C3 board with WiFi and BLE, battery support

Seeed Studio’s XIAO family of tiny MCU boards expands with the XIAO ESP32C3 board equipped with ESP32-C3 WiFi and Bluetooth LE (BLE) microcontroller, support for LiPo batteries, and following the same 21 x 17.5mm form factor. If I’m counting right, this is the fifth member following the original XIAO based on Microchip SAMD21G18 Cortex-M0+ MCU, XIAO RP2040, and the nRF52840-based XIAO BLE and XIAO BLE Sense boards which I tested with Edge Impulse. XIAO ESP32C3 specifications: Wireless MCU – Espressif Systems ESP32-C3 single-core RISC-V microcontroller @ 160 MHz with 400KB SRAM, 384KB ROM, 4MB flash Wi-Fi 4 & Bluetooth LE 5.0 connectivity Antenna – External u.FL antenna USB – USB Type-C port for power and programming Expansion I/Os 2x 7-pin headers with 1x UART, 1x I2C, 1x SPI, 11x GPIO (PWM), 4x ADC, I2S 3.3V I/O voltage (not 5V tolerant) Debugging – JTAG pads Misc – Reset button, Boot button, […]

April 22, 2022April 28, 2022 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

reServer Jetson-50-1-H4 is an AI Edge server powered by NVIDIA Jetson AGX Orin 64GB

Jetson AGX Orin 64GB AI inference server

reServer Jetson-50-1-H4 is an AI inference edge server powered by Jetson AGX Orin 64GB with up to 275 TOPS of AI performance, and based on the same form factor as Seeed Studio’s reServer 2-bay multimedia NAS introduced last year with an Intel Core Tiger Lake single board computer. The 12-core Arm server comes with 32GB LPDDR5, a 256GB NVMe SSD pre-loaded with the Jetpack SDK and the open-source Triton Inference server, two SATA bays for 2.5-inch and 3.5-inch drives, up to 10 Gbps Ethernet, dual 8K video output via HDMI and DisplayPort, USB 3.2 ports, and more. reServer Jetson-50-1-H4 (preliminary) specifications: SoM – Jetson AGX Orin module with CPU – 12-core Arm Cortex-A78AE v8.2 64-bit processor with 3MB L2 + 6MB L3 cache GPU / AI accelerators NVIDIA Ampere architecture with 2048 NVIDIA CUDA cores and 64 Tensor Cores @ 1.3 GHz DL Accelerator – 2x NVDLA v2.0 Vision Accelerator […]

April 11, 2022March 5, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

reComputer Jetson mini PCs feature Jetson Nano or Xavier NX modules

Seeed Studio’s reComputer Jetson series mini PCs are built around NVIDIA Jetson Nano or Xavier NX system-on-module and designed for Edge AI applications. Four models have been designed with the Jetson-10-1-A0 mini PC equipped with a carrier board of the same name and Jetson Nano module, while the Jetson A206 carrier board is integrated into Jetson-10-1-H0 also with Jetson Nano, as well as Jetson-20-1-H1 and Jetson-20-1-H2 based on Jetson Xavier NX with 8GB and 16GB RAM respectively. Jetson-10-1-A0 mini PC and carrier board Specifications: Jetson Nano SoM CPU – Quad-core Arm A57 processor @ 1.43 GHz GPU – Maxwell GPU with 128 CUDA cores System Memory – 4 GB 64-bit LPDDR4 25.6 GB/s Storage – 16 GB eMMC 5.1 Flash Video Encode – 4K @ 30 | 4x 1080p @ 30 | 9x 720p @ 30 (H.264/H.265) Video Decode – 4K @ 60 | 2x 4K @ 30 | 8x […]

December 2, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Seeed XIAO BLE – A tiny nRF52840 Bluetooth 5.0 board with (optional) IMU sensor and microphone

Seeed Studio has just introduced two new members to their XIAO board family with the Seeed XIAO BLE and XIAO BLE Sense boards equipped with Nordic Semi nRF52840 Bluetooth 5.0 microcontroller, as well as an IMU sensor and microphone on the “Sense” model. Just like the earlier XIAO RP2040 board, the tiny Seed XIAO BLE board can be programmed with Arduino, MicroPython, and CircuityPython, and offers two headers with 7-pin each for GPIOs. What’s really new is the wireless connectivity, the sensors, and a battery charging circuitry. Seeed XIAO BLE specifications: Wireless MCU – Nordic nRF52840 Arm Cortex-M4F microcontroller @ up to 64 MHz with 1 MB flash, 256 KB SRAM, Bluetooth 5.0, NFC, Zigbee connectivity Storage – 2 MB QSPI flash Expansion I/Os 2x 7-pin headers with 1x UART, 1x I2C, 1x SPI, 1x NFC, 1x SWD, 11x GPIO (PWM), 6x ADC 3.3V I/O voltage (not 5V tolerant) Sensors […]

November 19, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Jetson EX1 and SUB mini PCs put Xavier NX SoM into metal enclosures

Seeed Studio has just unveiled another Jetson Xavier NX mini PC with the Jetson EX1, plus some metal enclosures for the Jetson SUB mini PC announced last month with the official NVIDIA Jetson Xavier NX developer kit, a 128GB SSD, and the Re_Computer case comprised of an aluminum frame and a plastic cover. Jetson EX1 mini PC The Jetson EX1 mini PC has a different design with a custom carrier board offering dual Gigabit Ethernet and support for four MIPI CSI cameras, a 256GB NVMe SSD, and an aluminum enclosure designed to help with cooling, albeit the computer is not completely fanless since a 5V fan is included in the design as well. Jetson EX1 specifications: NVIDIA Jetson Xavier NX module CPU – 6-core NVIDIA Carmel ARMv8.2 64-bit processor with 6 MB L2 + 4 MB L3 cache GPU – NVIDIA Volta architecture with 384 NVIDIA CUDA cores and 48 […]

November 6, 2021November 8, 2021 by Jean-Luc Aufranc (CNXSoft) - 140 Comments

Giveaway Week – Arduino Sensor Kit Base

Day 6 of giveaway week 2021 will be for the Arduino Sensor Kit Base, a large board with six Arduino modules with Grove connector plus an Arduino shield with Grove connector. You could use it directly on top of an Arduino UNO or compatible to have a massive shield with multiple modules connected with Grove cable, or you could break it out into smaller modules as you see fit. The kit ships in a protective carrying plastic case with six Grove cables to connect the six Arduino modules to the Grove shield in the middle of the board. I told Seeed Studio I would not have time to review it, but they still sent it to me last December. So I’m here with a kit that I’m probably never going to use so better just give it away. You can enter the draw by simply leaving a comment with your […]

October 29, 2021November 1, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Jetson SUB mini PC ships with Xavier NX SoM, 128GB SSD

Jetson SUB is a mini PC powered by NVIDIA Jetson Xavier NX module and equipped with a 512GB 128GB SSD, a WiFi module, all housed in an aluminum case with a cooling fan. [Update Nov 1, 2021: Seeed Studio informed me the SSD would only have 128 GB capacity] Preloaded with NVIDIA Jetpack, the mini PC is designed for higher-end edge AI and IoT workloads leveraging the 384 NVIDIA CUDA cores, 48 Tensor cores, the hexa-core Carmel 64-bit Arm processor, and the two NVIDIA Deep Learning Accelerators (NVDLA) engines from the Xavier NX SoC. Jetson SUB mini PC specifications: NVIDIA Jetson Xavier NX module CPU – 6-core NVIDIA Carmel ARMv8.2 64-bit processor with 6 MB L2 + 4 MB L3 cache GPU – NVIDIA Volta architecture with 384 NVIDIA CUDA cores and 48 Tensor cores Accelerators – 2x NVDLA Engines, 7-Way VLIW Vision Processor Video – Multiple 4Kp60 encode, multiple […]