Reviews - Page 55 of 126 - CNX Software

June 26, 2019June 26, 2019 by Jean-Luc Aufranc (CNXSoft) - 26 Comments

4K Video Playback on Raspberry Pi 4 with LibreELEC (Alpha)

In my short Raspberry Pi 4 review, I tested 4K video output and playback in Raspbian, and sadly neither are working properly, with video output stuck to 1080p60 even after selecting 4K HDMI in the settings and yes, I double checked for “hdmi_enable_4k=1” in config.txt, while H.265 video playback is still clearly using software decode in both VLC and omxplayer. However, LibreELEC team announced support for Raspberry Pi 4 in LibreELEC 9.2 Alpha1 release based on Kodi 18.3 and Linux 4.19.x. So I downloaded LibreELEC-RPi4.arm-9.1.001.img.gz and flash it to a microSD card with balenaEtcher. The good news is that I could manually set the resolution to 3840×2160 and confirm it works with my TV, but the refresh is limited to 30 Hz maximum. Other refresh rates currently available include 23.98 Hz, 24 Hz, 25 Hz, and 29.97 Hz. The hardware is capable if 4K 60Hz, so it’s just a question […]

June 26, 2019 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

GPD P2 Max 8.9″ Ultrabook Launched on Indiegogo for $530 and Up

The previously unveiled GPD Pocket 2 Max has now launched on Indiegogo under the name GPD P2 Max. The mini laptop, which the company refers to as an Ultrabook, is powered by an Intel Core m3-8100Y Amber Lake processor coupled with up to 16GB RAM and 512GB SSD storage and features an 8.9″ high-resolution touchscreen display. Beside the Amber Lake processor, the company is also offering a lower cost model with an Intel Celeron 3965Y Kaby Lake-Y processor going for $530 in Indiegogo, against the $705 asked for the Intel Core m3-8100Y Ultrabook. GPD P2 Max Ultrabook specifications: SoC (one or the other) Intel Celeron 3965Y dual-core Kaby Lake processor @ 1.50 GHz with Intel HD graphics 615; 6W TDP Intel Core m3-8100Y dual-core/quad-thread Amber Lake processor @ 1.1 / 3.4 (Turbo) GHz with 24EU Intel UHD Graphics 615; 5W TDP, but configured with TDP-up @ 8W System Memory & […]

June 24, 2019June 30, 2019 by Jean-Luc Aufranc (CNXSoft) - 63 Comments

Raspberry Pi 4 Benchmarks & Mini Review

Raspberry Pi 4 has just been released with many improvements over Raspberry Pi 3 Model B+ including a faster processor, a proper Gigabit Ethernet port, USB 3.0 interfaces, and 4K video support. That’s the theory, but how does it work in practice? I can now let you know as I’ve received a Raspberry Pi 4 sample courtesy of Cytron, and ran some tests and benchmarks on the very latest boards from the Raspberry Pi foundation. System Info Before starting with the benchmarks, let’s go through some basic system info:

pi@raspberrypi:~ $ cat /etc/issue
Raspbian GNU/Linux 10 \n \l

pi@raspberrypi:~ $ uname -a
Linux raspberrypi 4.19.46-v7l+ #866 SMP Fri Jun 7 18:00:39 BST 2019 armv7l GNU/Linux

pi@raspberrypi:~ $ df -h
Filesystem      Size  Used Avail Use% Mounted on
/dev/root        13G  4.7G  7.4G  39% /
devtmpfs        334M     0  334M   0% /dev
tmpfs           463M     0  463M   0% /dev/shm
tmpfs           463M  6.4M  456M   2% /run
tmpfs           5.0M  4.0K  5.0M   1% /run/lock
tmpfs           463M     0  463M   0% /sys/fs/cgroup
/dev/mmcblk0p6  253M   40M  213M  16% /boot
tmpfs            93M     0   93M   0% /run/user/1000
/dev/sda4       200G  175G   24G  89% /media/pi/USB3_BTRFS
/dev/sda2       241G  181G   48G  80% /media/pi/USB3_EXT4
/dev/sda1       245G  182G   63G  75% /media/pi/USB3_NTFS

pi@raspberrypi:~ $ cat /proc/cpuinfo 
processor	: 0
model name	: ARMv7 Processor rev 3 (v7l)
BogoMIPS	: 270.00
Features	: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32 
CPU implementer	: 0x41
CPU architecture: 7
CPU variant	: 0x0
CPU part	: 0xd08
CPU revision	: 3

....
processor	: 3
model name	: ARMv7 Processor rev 3 (v7l)
BogoMIPS	: 270.00
Features	: half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32 
CPU implementer	: 0x41
CPU architecture: 7
CPU variant	: 0x0
CPU part	: 0xd08
CPU revision	: 3

Hardware	: BCM2835
Revision	: a03111
Serial		: 00000000ea51204b

pi@raspberrypi:~ $ cat /etc/issue

Raspbian GNU/Linux 10 \n \l

pi@raspberrypi:~ $ uname -a

Linux raspberrypi 4.19.46-v7l+ #866 SMP Fri Jun 7 18:00:39 BST 2019 armv7l GNU/Linux

pi@raspberrypi:~ $ df -h

Filesystem Size Used Avail Use% Mounted on

/dev/root 13G 4.7G 7.4G 39% /

devtmpfs 334M 0 334M 0% /dev

tmpfs 463M 0 463M 0% /dev/shm

tmpfs 463M 6.4M 456M 2% /run

tmpfs 5.0M 4.0K 5.0M 1% /run/lock

tmpfs 463M 0 463M 0% /sys/fs/cgroup

/dev/mmcblk0p6 253M 40M 213M 16% /boot

tmpfs 93M 0 93M 0% /run/user/1000

/dev/sda4 200G 175G 24G 89% /media/pi/USB3_BTRFS

/dev/sda2 241G 181G 48G 80% /media/pi/USB3_EXT4

/dev/sda1 245G 182G 63G 75% /media/pi/USB3_NTFS

pi@raspberrypi:~ $ cat /proc/cpuinfo

processor : 0

model name : ARMv7 Processor rev 3 (v7l)

BogoMIPS : 270.00

Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32

CPU implementer : 0x41

CPU architecture: 7

CPU variant : 0x0

CPU part : 0xd08

CPU revision : 3

....

processor : 3

model name : ARMv7 Processor rev 3 (v7l)

BogoMIPS : 270.00

Features : half thumb fastmult vfp edsp neon vfpv3 tls vfpv4 idiva idivt vfpd32 lpae evtstrm crc32

CPU implementer : 0x41

CPU architecture: 7

CPU variant : 0x0

CPU part : 0xd08

CPU revision : 3

Hardware : BCM2835

Revision : a03111

Serial : 00000000ea51204b

$ inxi -Fc0
System:
  Host: raspberrypi Kernel: 4.19.46-v7l+ armv7l bits: 32 Console: tty 1 
  Distro: Raspbian GNU/Linux 10 (buster) 
Machine:
  Type: ARM Device System: Raspberry Pi 4 Model B Rev 1.1 details: BCM2835 
  rev: a03111 serial: 00000000ea51204b 
CPU:
  Topology: Quad Core model: ARMv7 v7l variant: cortex-a72 bits: 32 
  type: MCP 
  Speed: 1500 MHz min/max: 600/1500 MHz Core speeds (MHz): 1: 1500 2: 1500 
  3: 1500 4: 1500 
Graphics:
  Device-1: bcm2835-vc4 driver: vc4_drm v: N/A 
  Device-2: bcm2835-hdmi driver: N/A 
  Display: tty server: X.org 1.20.4 driver: modesetting unloaded: fbdev 
  tty: 80x24 
  Message: Advanced graphics data unavailable in console. Try -G --display 
Audio:
  Device-1: bcm2835-audio driver: bcm2835_audio 
  Device-2: bcm2835-hdmi driver: N/A 
  Sound Server: ALSA v: k4.19.46-v7l+ 
Network:
  Message: No ARM data found for this feature. 
  IF-ID-1: eth0 state: up speed: 1000 Mbps duplex: full 
  mac: dc:a6:32:00:9e:9c 
  IF-ID-2: wlan0 state: up mac: dc:a6:32:00:9e:9d 
Drives:
  Local Storage: total: 946.35 GiB used: 540.58 GiB (57.1%) 
  ID-1: /dev/mmcblk0 vendor: SanDisk model: SL16G size: 14.84 GiB 
  ID-2: /dev/sda type: USB vendor: Seagate model: Expansion size: 931.51 GiB 
Partition:
  ID-1: / size: 12.68 GiB used: 4.71 GiB (37.1%) fs: ext4 
  dev: /dev/mmcblk0p7 
  ID-2: /boot size: 252.0 MiB used: 39.3 MiB (15.6%) fs: vfat 
  dev: /dev/mmcblk0p6 
Sensors:
  Message: No sensors data was found. Is sensors configured? 
Info:
  Processes: 179 Uptime: 4h 37m Memory: 1000.5 MiB used: 324.1 MiB (32.4%) 
  gpu: 76.0 MiB Init: systemd runlevel: 5 Shell: bash inxi: 3.0.32

$ inxi -Fc0

System:

Host: raspberrypi Kernel: 4.19.46-v7l+ armv7l bits: 32 Console: tty 1

Distro: Raspbian GNU/Linux 10 (buster)

Machine:

Type: ARM Device System: Raspberry Pi 4 Model B Rev 1.1 details: BCM2835

rev: a03111 serial: 00000000ea51204b

CPU:

Topology: Quad Core model: ARMv7 v7l variant: cortex-a72 bits: 32

type: MCP

Speed: 1500 MHz min/max: 600/1500 MHz Core speeds (MHz): 1: 1500 2: 1500

3: 1500 4: 1500

Graphics:

Device-1: bcm2835-vc4 driver: vc4_drm v: N/A

Device-2: bcm2835-hdmi driver: N/A

Display: tty server: X.org 1.20.4 driver: modesetting unloaded: fbdev

tty: 80x24

Message: Advanced graphics data unavailable in console. Try -G --display

Audio:

Device-1: bcm2835-audio driver: bcm2835_audio

Device-2: bcm2835-hdmi driver: N/A

Sound Server: ALSA v: k4.19.46-v7l+

Network:

Message: No ARM data found for this feature.

IF-ID-1: eth0 state: up speed: 1000 Mbps duplex: full

mac: dc:a6:32:00:9e:9c

IF-ID-2: wlan0 state: up mac: dc:a6:32:00:9e:9d

Drives:

Local Storage: total: 946.35 GiB used: 540.58 GiB (57.1%)

ID-1: /dev/mmcblk0 vendor: SanDisk model: SL16G size: 14.84 GiB

ID-2: /dev/sda type: USB vendor: Seagate model: Expansion size: 931.51 GiB

Partition:

ID-1: / size: 12.68 GiB used: 4.71 GiB (37.1%) fs: ext4

dev: /dev/mmcblk0p7

ID-2: /boot size: 252.0 MiB used: 39.3 MiB (15.6%) fs: vfat

dev: /dev/mmcblk0p6

Sensors:

Message: No sensors data was found. Is sensors configured?

Info:

Processes: 179 Uptime: 4h 37m Memory: 1000.5 MiB used: 324.1 MiB (32.4%)

gpu: 76.0 MiB Init: systemd runlevel: 5 Shell: bash inxi: 3.0.32

For reference, you’ll find Raspberry Pi 4 Linux boot log here. Phoronix benchmarks Let’s go ahead and install the latest version of Phoronix benchmarks:

sudo apt install php-cli php-gd php-xml php-zip 
wget http://phoronix-test-suite.com/releases/repo/pts.debian/files/phoronix-test-suite_8.8.1_all.deb
sudo dpkg -i phoronix-test-suite_8.8.1_all.deb

sudo apt install php-cli php-gd php-xml php-zip

wget http://phoronix-test-suite.com/releases/repo/pts.debian/files/phoronix-test-suite_8.8.1_all.deb

sudo dpkg -i phoronix-test-suite_8.8.1_all.deb

Now let’s run the test to compare the performance of Raspberry Pi 4 model B to some other Arm Linux boards including Raspberry Pi 3 Model B.

phoronix-test-suite benchmark 1709271-TY-1704029RI26

1	phoronix-test-suite benchmark 1709271-TY-1704029RI26

For reference, my office has an […]

June 24, 2019July 17, 2019 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

ODROID-H2 Rev B Review – Part 1: Kit Unboxing and Assembly

ODROID-H2 was announced in October 2018 as the first x86 SBC from Hardkernel. The board features an Intel Celeron J4105 Gemini Lake processor, two SO-DIMM slots for memory, two SATA ports and M.2 NVMe slot for storage, two Gigabit Ethernet ports, a mix of USB 3.0 and 2.0 ports, as well as HDMI and DisplayPort video outputs. The board went for sale the following month for $111, and the first batch of 2,000 boards was sold within 24 hours. In normal cases, this should not be a big problem, and in a few weeks, the company should have been able to produce more boards to fulfill the demand. But Intel decided to prioritize higher-end processors, and Gemini Lake SoCs’ manufacturing was put on the back foot. That means Hardkernel had to wait over 6 months to get supply of the Celeron J4150 processors. In the meantime, the company slightly redesign […]

June 18, 2019 by Karl Johnson - 11 Comments

Review of SainSmart Genmitsu CNC Router 3018-MX3

Hey Karl here. Back in September of 2018 I reviewed the Sainsmart Genmitsu 3018 Pro. Sainsmart has now further upgraded the 3018 and asked for a review of it. Let’s take a look at the changes and the evolution of the 3018 and see if the increase in price is worth it. You can find the original 3018 on sale for about $200. The pro version can be found for about $250, and the CNC Router 3018-MX3 for $350. I won’t go into too much detail like I did in the previous review. I suggest reading the pro version after reading this one. Most of the experiences and solutions apply to this version. Build Building the CNC Router 3018-MX3 was a breeze. The instructions are fantastic. I struggled a little bit to read the small booklet that came with the kit and afterwards I found a PDF on the Sainsmart […]

June 16, 2019June 16, 2019 by Jean-Luc Aufranc (CNXSoft) - 17 Comments

Reolink Argus Eco Review – A Sub-$100 Solar Powered Security Camera

Reolink Argus Eco IP Camera Wall Mounted

I’ve been thinking about installing one or more IP camera in my home for a while, and for ease of installation and considering I’m renting, my preference was to go with one of those battery IP cameras similar to Amazon (Immedia) Blink IP camera or Eufy EverCam security camera that last six months to one year on a single charge. But earlier this year I came across Reolink Argus 2 battery powered security camera that looks like good value at $100, and also came with an optional solar panel so you don’t have to ever charge the camera. The company latter contacted me to know whether I’d be willing to try out their latest Reolink Argus Eco camera with similar features but an even lower $89.99 price tag. I got my sample a few weeks ago, and I had time to install it, and play around with the camera during […]

June 4, 2019June 4, 2019 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

HT-102 is a $130 Thermal Camera for Android Phones

Thermal cameras are useful to accurately monitor the temperature of electronics components, people, fires, houses, and so on. Thermal imaging cameras can be relatively expensive and one way to lower the cost and make sharing of results easier is to get a model that connects to your smartphone. The ones listed on Amazon cost $200 and up, but you’ll find HT-102 thermal camera for Android phones on Chinese websites such as GearBest or Banggood for around $130. HT-102 specifications: Material: metal Capture Temperature Range – -20 to 300°C Accuracy – ±3℃ or ±5% of reading Resolution – 0.1℃ or 0.1℉ Working band – 8-14μm Horizontal viewing angle / vertical viewing angle – 43°±1°/ 43°±1° Infrared image resolution – 32 x 32 Visible image resolution – 640 x 480 Phone I/F – USB type-C port for data and power Dimensions – 60 x 30 mm Weight – 19 grams Temperature Range […]

June 2, 2019June 3, 2019 by Karl Johnson - 17 Comments

Review of Zonestar Z6 Low-cost 3D Printer

Ugh…I don’t like calling these reviews. I like to say that I am sharing my experiences with the products. I have a fair bit of experience under my belt using 3D printers now but still don’t consider myself an “expert”. I think that I have had about a dozen come through here. Anyway on with the show. Today we are going to look at a very economical 3D printer: the Zonestar Z6. I have to say I wasn’t expecting much. I read/ watch a lot of reviews about 3D printers and sub $100 printers aren’t typically very good. Gearbest recently had the Zonestar Z6 on sale for $99 that Jean-Luc recently posted here on CNX Software but is currently $120. Let’s see how it prints. Some assembly required I designed a spool holder but not very good. The whole printer rocks when the full spool is on it. The tiny […]