Raspberry Pi News - Page 158 of 179 - CNX Software

July 25, 2015June 18, 2018 by Jean-Luc Aufranc (CNXSoft) - 28 Comments

NanoPi is a $16 WiFi and Bluetooth LE Linux Development Board

NanoPi is a new Linux development board powered by Samsung S3C2451 ARM9 processor with Wi-Fi and Bluetooth LE connectivity, connectors for a camera and an LCD display, as well as two expansion headers including a 40-pin “Raspberry Pi compatible” header. NanoPi specifications: Processor – Samsung S3C2451 ARM9 @ 400Mhz System Memory – 64M DDR2 Storage – micro SD slot Connectivity – AP6210 module for 802.11 b/g/n WiFi and Bluetooth 4.0 USB – 1x USB 1.1 host port, 1x micro USB OTG port for power and data (serial or Ethernet) Display I/F – LCD Interface: 0.5mm pitch SMT FPC seat, support full-color LCD (RGB: 8-8-8) Camera I/F – DVP Camera Interface: 0.5mm pitch FPC connector, including ITU-R BT 601/656 8-bit, I2C and GPIOs Debugging – Serial Port Expansion Headers “GPIO1” – 40-pin header including UART, SPI, I2C, GPIO pins (Raspberry Pi compatible) “GPIO2” – 12-pin header including I2S, I2C, UART pins Power – […]

July 5, 2015 by Jean-Luc Aufranc (CNXSoft) - No Comments

Gesto is a Wearable Gesture Motion Solution for Makers (Crowdfunding)

A while ago I wrote about an open source prosthetic arm controlled by signals generated by your arm’s muscles. It used an Arduino board, a bio-feedback shield by Olimex, and inMoov Hand for the arm and hand. It worked, but lacked accuracy. Gesto is a solution based on boards powered by Atmel MCUs that looks somewhat similar, but with higher accuracy (over 100 gestures have been tested), and the project has now been launched on Crowdsupply. Two kits are available: Gesto Stella EMG circuit – ADS1294 MCU – Atmel ATmega1284p 2x EMG cables connector Through holes with GND, PWR, MOSI, MISO, CLK and SC Dimensions – 35 x 20 mm Includes 16 disposable electrodes and relevant cables Gesto Caelum EMG circuit – ADS1294 MCU – Atmel ATmega1284p Sensors – 3-axis accelerometer (MMA8652FC) Connectivity – Bluetooth (RN42-HID) 2x EMG cables connector USB – Micro USB connector Programming – ICSP connector Power […]

May 16, 2015 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Raspberry Pi Model B+ Price Drops to $25

When Raspberry Pi 2 was launched, Raspberry Pi Model B+ kept getting sold for $35 despite the lower specifications, but a week later resellers started selling Model B+ for as low as $30 shipped. But the Raspberry Pi foundation now announced an official new price for Raspberry Pi Model B+, which now sells for just $25 on RS Components and MCM Electronics with other resellers to soon follow. This makes R-Pi Model B+ relevant again for applications that do not require the extra horse power or memory brought by R-Pi 2 quad core processor and 1GB RAM. Jean-Luc Aufranc (CNXSoft)Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software engineering manager, and starting to write daily news, and reviews full time later in 2011. www.cnx-software.com

April 30, 2015April 30, 2015 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

Windows 10 IoT Preview for Raspberry Pi 2 and MinnowBoard Max

When Raspberry Pi 2 Model B was released, we were promised a Windows 10 image for the board, and today, Microsoft released “Windows 10 IoT Core Insider Preview” for both the Broadcom BCM2836 based Raspberry Pi 2 and Intel Atom E3800 series based Minnowboard MAX boards. To get started with either board, simply go to Windows IoT – Getting Started page. I’ll quickly go through the instructions for Raspberry Pi 2. Beside the board, you’ll also need a PC running Windows 10 Insider preview (Virtual machine not supported), a 5V power supply, a HDMI cable (optional but recommended), an Ethernet cable, and a 8GB micro SD card, class 10 or better. The you’ll need to configure a connect account, where I had to accept two EULA including “Windows 10 IoT Core Insider Preview EULA”, and once this is done the area of the page for EULA should just be blank, […]

April 25, 2015April 25, 2015 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

$10 Digistump Oak ESP8266EX Board is Arduino Compatible, Connects to the Cloud, and More (Crowdfunding)

A few years ago, I wondered why adding Wi-Fi to Arduino had to be rather expensive ($40+), and why there weren’t any low cost and small form factor Wi-Fi boards for embedded applications. But we’re now in 2015, embedded is “dead” giving rise to IoT, and I’m left wondering how it’s possible to make IoT Wi-Fi modules that cheap, and whether people will ever stop churning out cheap Wi-Fi boards, as I’m flooded with such news weekly… So when I saw yet another ESP8266 board on Kickstarter I was about to dismiss it, but since it was made by Digistump, that has an active community with their other products like DigiSpark Pro or DigiX, I decided to have a closer look. Digistump Oak hardware specifications: MCU – Espressif ESP8266EX 32-bit microprocessor @ 80MHz (overclockable up to 160MHz) with 1MB ROM (~300KB available for user code), 64KB RAM, 512 bytes EEPROM […]

April 20, 2015April 20, 2015 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Tizen OS Ported to the Raspberry Pi 2

Tizen may not be overly used in devices, but there has been ports of the operating system on various ARM platform, mostly development boards, powered by Allwinner, Rockchip, Freescale SoCs, and more… Seeing the popularity of Raspberry Pi 2 Model B, Samsung Open Source Group decided to port Tizen to the latest version of the hobbyist board. The full instructions are rather long, and provided in the link above, but the main steps – using a Linux based computer – can be summarized as follows: Create a local copy of tizen-distro Add Raspberry Pi 2 BSP Meta repository Initialize the environment and modify some config files Start the build with Yocto: bitbake rpi-hwup-image. This should make a minimal headless? image Create an SD card image with tmp-glibc/deploy/images/raspberrypi2/rpi-hwup-image-raspberrypi2.rpi-sdimg using dd, an optional resize the parition with gparted or fdisk/resize2fs. Insert the SD card in to your Raspberry Pi 2, and have […]

April 12, 2015 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

ARDHAT adds Arduino Shield Compatibility, an ISM Band Radio to Raspberry Pi and ODROID-C1 Boards (Crowdfunding)

NinjaBlocks created Pi Crust add-ons board adding a 433MHz radio and Arduino compatibility to the Raspberry Pi Model A & B a few years ago, but the product has since been removed from their store. But a startup called ubIQio has now created a similar product compatible with Raspberry Pi Model A+, B+ and B2, as well as ODROID-C1 which also comes with a 40-pin R-Pi header. The ARDHAT board is a HAT compatible add-on board with an Atmel MCU, Arduino headers, as well as an optional long range mesh ISM radio (433, 868 and 915 MHz) and various sensors. There are four versions of the board: Basic Ardhat, Ardhat-I, and Ardhat-W and Ultra, which share the following specifications: MCU – Atmel MCU @ 16MHz Headers and I/Os Arduino compatible header accepting 5V Arduino shields 12 ch PWM O/P, 6 ch analog I/P Real-time Clock Programmable Power/Navigation combo switch Programmable […]

April 3, 2015 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Kodi 14.2 Final and Kodi 15 Alpha 2 Released

Kodi developers have recently announced two release for Kodi: the stable version of Kodi 14.2 Helix, which should be the last Kodi 14 release, and Kodi 15 Alpha 2 Isengard with some interesting new features. Since Kodi 14.2 is a minor release, no new features have been added, but they fixed several bugs: Application stopped responding on Windows Gap-less playback on MP3 Playback of rtmp protocol Scanning of newly added episodes Fix multipath source scanning Loading external subtitles in some cases packaging of PIL module on Android. This fixes some script error when using weather add-on Fix video playback on all platform after refresh rate change Various bugs that were present in PVR add-ons. Save weather location Fix filtering of foreign add-ons ftps handling Use LastWrite instead of ChangeTime for file system on Windows As usual, you can download the release via Kodi download page for Windows, Linux. Mac OS […]