power News - CNX Software - Embedded Systems News

January 31, 2025February 3, 2025 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Brodboost-C is a USB Type-C breadboard power supply board with adjustable 3.3V or 5V voltage (Crowdfunding)

BrodBoost-C USB C power supply breadboard

Axiometa BrodBoost-C is a USB Type-C breadboard power supply with a simple design that powers both rails of a breadboard with voltage adjustable between 3.3V or 5V. It also includes an on/off switch, an LED indicator, and built-in fuse protection. BrodBoost-C specifications: Output voltage – Adjustable: 3.3V or 5V DC Maximum current – 1A Ports USB Type-C connector for power input 2x 2×5 2.54 mm breadboard-compatible power and ground rails 2x 3-pin 2.54 mm selection headers with 2x jumper caps Safety – Short circuit protection Input filtering – Ferrite bead for noise suppression and decoupling capacitors Misc – Red Power LED, ON/OFF power switch Voltage regulation: 5.0 V selected by USB CC Pins (5.1 k resistors) 3.3 V step-down regulation via AMS1117-3.3 Dimensions – 54 x 19.5 x 11.4 mm Weight – About 20 grams We’ve written about several breadboard power supplies over the years including the Toaster board with […]

January 27, 2025January 26, 2025 by Debashis Das - 5 Comments

STM32H7-powered open-source hardware 3D printer mainboard supports up to 6 stepper drivers

SmartPrintCoreH7x Open Source 3D Printer Mainboard

Designed by Boltz R&D, the SmartPrintCoreH7x 3D printer mainboard is an open-source mainboard built around an STM32H7 microcontroller and designed to work with 3D printers from Creality, Anet, and Voron. It supports up to 6 stepper drivers (5 standard drivers plus 1 dedicated driver) and can be expanded further using the “SmartPrintCore Extravaganza” module for additional stepper drivers. Key features of this motherboard include a jumper-less setup, automatic power source switching, and support for both 12V and 24V power supplies. It uses high-efficiency TI buck converters to provide power for multiple fan and servo ports, and there is a dedicated power supply for peripherals, SBCs, and Wi-Fi modules. The board is equipped with a variety of connectors, including Molex, Ultra-Fit, Mini-Lock, and JST-GH for power, motors, and peripherals. SmartPrintCoreH7x specifications: MCU – STMicro STM32H723 Arm Cortex-M7 32-bit core @ 550 MHz with 1MB Flash, 564 KB RAM, FPU, DSP, Ethernet, USB […]

January 16, 2025 by Jean-Luc Aufranc (CNXSoft) - No Comments

USB-C and Lightning tester features an LCD display showing the voltage of each pin

VBEST’s Tail Insert Detector is a USB-C and Lightning cable/device tester that reports “real-time” current and voltage of each pin on its built-in display for easy debugging and testing. VBEST Tail Insert Detector highlights and specifications: Port compatibility – USB Type-C male and Lightning male ports Display – Color LCD display Features – Real-time current and voltage detection Misc – Push switch for power and display mode Power 5V via USB-C female port (on the side) Built-in battery Dimensions – 52 x 35 (estimated) x 14mm Sadly, there’s not much in the way of documentation, so it’s unclear how many display modes there are. I’m also confused by the “real-time” voltage and current reporting, because we’re also told it takes 5 seconds to detect “abnormal pins”. The VBEST’s device is very similar to the A2C caberQU and C2C caberQU boards used to respectively test USB-A to USB-C and USB-C to […]

January 14, 2025 by Tomisin Olujinmi - 2 Comments

Ditronix’s IPEM PiHat turns your Raspberry Pi into a mains power energy monitor (Crowdfunding)

Raspberry Pi 5 IPEM Power Energy Monitor

The IPEM PiHat is a HAT (Hardware Attached on Top) board for the Raspberry Pi that turns the single-board computer into a mains power energy monitor with four CT clamps. It provides an accurate way to track energy usage in home, office, and solar energy systems and is compatible with single-phase, two-phase, and three-phase electrical systems. The Raspberry Pi-based power energy monitor uses CT (current transformer) cable clamps to sample and measure data which can be used to report and analyze electric energy usage. This data can be used to save and divert energy to reduce costs and inefficiencies. The system is easy to set up and does not require a professional electrician. It uses a CT current clamp clipped over the building’s main power cables and connected to the local mains circuit for voltage and frequency measurement. The add-on board comes in two variants: IPEM PiHat and IPEM PiHat […]

January 12, 2025January 12, 2025 by Debashis Das - 13 Comments

GuRu’s modular wireless power transfer system can power a drone indefinitely

California-based company GuRu Wireless has recently developed and showcased a scalable and modular wireless power transfer system that is capable of delivering power to a high-power device up to several kilowatts, such as a drone, from up to 30 feet away (a little over 9 meters). They also mention that the system can power low-power devices, like LEDs and consumer electronics, over distances of several kilometers. It’s quite an extension to the GuRu’s desk-range wireless power evaluation kit we covered in 2020. The system uses 24 GHz high-frequency millimeter-wave radio signals to deliver energy over long distances without needing batteries or tethered systems. GuRu’s system uses a phased array transmitter with proprietary RFICs, to precisely deliver power to the receiver called the Recovery Unit (RU). In a recent demonstration video, GuRu Wireless showcased their wireless power transfer system by powering a drone from 30 feet away, operating it continuously for […]

January 6, 2025January 5, 2025 by Tomisin Olujinmi - No Comments

PicoPD Pro – An open-source RP2040 development board with USB PD support up to 30V

The PicoPD Pro is an open-source Raspberry Pi RP2040 development board that integrates USB PD support up to 30V, and features like voltage negotiation and power delivery while still retaining the Raspberry Pi Pico functionality. It features the AP33772S USB-C PD3.1 sink controller from Diodes Incorporated. The AP33772S supports the full USB-C PD 3.1 specification, including Extended Power Range (EPR) / Adjustable Voltage Supply (AVS) up to 28V and Programmable Power Supply (PPS) up to 21V. The PicoPD Pro USB PPS/AVS development board is ideal for powering devices with specific requirements, such as motor control boards, LED drivers, custom battery chargers, and other high-power applications. It also features a 5V rail output for less demanding applications. It can also be used as an AP33772S evaluation board. We have previously seen other USB-C PD solutions like the Spark Analyzer, YULC LED Controller, and USB Insight Hub which may serve a similar […]

December 6, 2024 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

XIAO Powerbread is a breadboard power supply and meter based on XIAO RP2040 or ESP32 USB-C board

XIAO Powerbread power meter for breadboard

The XIAO Powerbread is a breadboard power supply and meter compatible with XIAO RP2040 or ESP32 USB-C boards and equipped with a color LCD display showing real-time voltage, current, and power consumption for 5V and/or 3.3V power rails. Breadboard power supplies are nothing new. We’ve written about several over the years including the Toaster board with adjustable voltage from 5 to 16V, the SwitchTrick switching power supply board, and the MEGO portable breadboard power supply with a built-in battery. The XIAO Powerbread only supports 5V and 3.3V power rails, but its main selling point is its integrated breadboard power meter function. XIAO Powerbread specifications: Supported USB-C modules General purpose MCU – XIAO RP2040, XIAO RP2350 WiFi / Bluetooth MCU – XIAO ESP32S3, XIAO ESP32C3, XIAO ESP32C6 Display – 0.96-inch color TFT LCD with 160×80 resolution and ST7735S SPI controller Power monitoring – 2x TI INA3221 sensors connected over I2C […]

October 23, 2024October 23, 2024 by Karl Johnson - 2 Comments

EBL MP1000 Review – A 1000W portable AC/DC power station with solar panels

Hey, Karl here and I am getting old. I guess middle age is more accurate. Two wonderful kids and I want to stick around for a while. I have not been feeling well and as a result, I picked up strength training as a form of exercise. I started with an adjustable bench and a set of adjustable dumbbells. I trained with them for about 3 months in my office. I had just enough space. I was hooked. I dove in and learned as much as I could on current best practices, and developed a spreadsheet for tracking progress. I started to outgrow the 55lb/25kg adjustable dumbbells with several exercises and the next step was a squat rack, bar, and Olympic weights. My problem was the lack of space. I had a building that was poorly organized. After a bit of organizing, I was able to carve enough space for […]