orange pi News - Page 12 of 22 - CNX Software

May 29, 2018 by Jean-Luc Aufranc (CNXSoft) - 24 Comments

Orange Pi 3G-IoT SBC Launched for $24.90

We had two Arm Linux SBCs with cellular connectivity from Shenzhen Xunlong so far: Orange Pi 2G-IoT for 2G connectivity, and Orange Pi 4G-IoT with LTE support in Asia and Europe. But what if you needed 3G connectivity, and did not want to spend $45 on the 4G board? There was no option until today, but the company has just launched Orange Pi 3G-IoT with WCDMA (UMTS), TD-CDMA and CDMA2000 support. Orange Pi 3G-IoT-B board specifications: SoC – MediaTek MT6572 dual core Cortex A7 processor @ up to 1.2 GHz with Arm Mali-400 GPU System Memory – 512MB DDR2 Storage – 4GB eMMC flash, micro SD slot Display I/F – FPC connector for FWVGA display (854×480) Camera I/F – MIPI connector Audio – 3.5mm audio jack, built-in microphone, 2x solder pads for optional speakers Connectivity Cellular Nano SIM card slot 2G GSM – 850/900/1800/1900 MHz 3G WCDMA -(B1/B2/B5/B8), TD-CDMA, CDMA2000 […]

May 24, 2018May 24, 2018 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Android 8.1 Firmware and SDK Released for Orange Pi 4G-IoT Board

When Orange Pi 4G-IoT board launched a few months ago, it shipped with a not so recent Android 6.0 operating system. But the good news is that Shenzhen Xunlong Software has now released Android 8.1 firmware for their Mediatek MT6737M quad core Cortex A53 LTE Cat 4 board, as well as the corresponding SDK. This makes it the cheapest Android 8.1 board with LTE connectivity available on the market so far as it goes for just under $50. The SDK is a large tarball (22.6 GB) split into 11 smaller files. It’s hosted on MEGA so download is fairly fast, but due to the size I had to install MEGA Sync software in order to download it easily. Once the download is complete, it’s not recognized in Nautilus, but you can extract the SDK as follows in a terminal:

cd 4G-IOT_Android 8.1 SDK
cat x* &gt; OrangePi_4G-IOT_Android8.1.tar.gz
tar xvf OrangePi_4G-IOT_Android8.1.tar.gz

cd 4G-IOT_Android 8.1 SDK

cat x* > OrangePi_4G-IOT_Android8.1.tar.gz

tar xvf OrangePi_4G-IOT_Android8.1.tar.gz

This will take a while and extract over a million […]

April 23, 2018 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

24 Orange Pi Zero Boards Cluster and ArmWizard’s Debian Image

ArmWizard forum member “-W.-” needed a cluster to test his firmware build and deployment solution for Orange Pi Zero boards which can deploy the firmware to multiple boards from one single board. So he procured 24 Orange Pi Zero boards, a 24-port switch, some USB hubs and debug board, as well as some other accessories, power supplies, and two wooden planks. That’s the results after assembly. So we have 4 tower of six Orange Pi Zero boards fairly neatly connected to the 24-port Ethernet switch with 30 cm Ethernet cables, and four black USB hubs for the USB to TTL debug boards. The side view below shows the boards are powered by micro USB cables connected to three different power supplies, cooling achieved via four fans, and the power extension is hidden right underneath close to the Ethernet switch. The cluster will also be used for machine learning latter on, […]

April 6, 2018April 6, 2018 by Jean-Luc Aufranc (CNXSoft) - 34 Comments

Shedbuilt Binary Blob-Free Linux Distribution Works with Allwinner H3/H5 Boards (Orange Pi, Libre Computer)

Most open source Linux distributions are only partially open source, as while most packages will be built from publicly available source code, they usually come with closed source binary blobs for GPU drivers, wireless module firmware and so on. Shedbuilt is described as “a decentralized, self-hosting GNU/Linux for Arm devices built from the latest upstream sources”, and as the developer (Auston Stewart) explains – see comments section – it does not contain any binary blob. Eventually the distribution may support more boards, but for now, the current System 1 “Amano” release supports four Allwinner H3/H5 boards: Orange Pi PC, Orange Pi One, Orange Pi PC 2, and Libre Computer ALL-H3-CC “Tritium”. Orange Pi Lite (with WiFi) and Libre Computer AML-S905X-CC “Le Potato” images are said to be coming soon. You can download the SD card images and access documentation on Shedbuilt.net. The Linux distribution relies on Shedmake script to automate […]

April 2, 2018April 3, 2018 by Jean-Luc Aufranc (CNXSoft) - No Comments

Linux 4.16 Release – Main Changes, Arm and MIPS Architectures

Linus Torvalds has just released Linux 4.16: So the take from final week of the 4.16 release looks a lot like rc7, in that about half of it is networking. If it wasn’t for that, it would all be very small and calm. We had a number of fixes and cleanups elsewhere, but none of it made me go “uhhuh, better let this soak for another week”. And davem didn’t think the networking was a reason to delay the release, so I’m not. End result: 4.16 is out, and the merge window for 4.17 is open and I’ll start doing pull requests tomorrow. Outside of networking, most of the last week was various arch fixlets (powerpc, arm, x86, arm64), some driver fixes (mainly scsi and rdma) and misc other noise (documentation, vm, perf). The appended shortlog gives an overview of the details (again, this is only the small stuff in […]

March 23, 2018May 24, 2018 by Jean-Luc Aufranc (CNXSoft) - 39 Comments

Orange Pi 4G-IoT Development Board Launched for $45

Last year, Shenzhen Xunlong Software launched Orange Pi 2G-IoT board for just $9.90. Pricing was incredibly aggressive for a cellular board, but AFAIK the RDA Micro processor used in the design had never been used with Linux so for many people using the board was a challenge (and maybe still is), and some countries have already started to sunset 2G networks. So it only made sense for the company to work on a 4G board, and that’s exactly what they have done with Orange Pi 4G-IoT now launched for $45 + shipping on Aliexpress. Orange Pi 4G-IoT specifications: SoC – Mediatek MT6737 quad core Cortex A53 processor @ 1.1/1.3 GHz with Arm Mali-T720MP1 GPU System Memory – 1GB DDR3 Storage – 8GB eMMC flash + micro SD slot Video Output – HDMI, LCD display interface with touch panel support Audio – 3.5mm earphone jack, built-in microphone Cellular Connectivity nano SIM […]

February 8, 2018 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

TECHBASE ModBerry M300 IoT Gateway Adds Support for NanoPi and Orange Pi Allwinner H5 Boards

Announced at the end of last year TECHBASE launched the ModBerry M300, a Linux IoT gateway powered by FriendlyELEC NanoPi NEO board equipped with Allwinner H3 Cortex A7 processor. The company has now made four extra variants of the gateway with Allwinner H5 quad core Cortex A53 based development boards from FriendlyELEC and Shenzhen Xunlong: Modberry M300 N2 – Based on NanoPi NEO2 Modberry M300 N2+ – Based on NanoPi NEO Plus2 adding 8GB eMMC flash, WiFi & Bluetooth 4.0, and an extra USB port over the N2 model Modberry M300 O1 – Based on Orange Pi Zero Plus Modberry M300 O2 – Based on Orange Pi Zero Plus2 adding 8GB eMMC flash, HDMI, one extra USB port, and Bluetooth 4.0 over the O1 model, but falling back to 10/100 Ethernet, while all three models above come with Gigabit Ethernet To avoid confusion, the original NanoPi NEO model has changed […]

January 29, 2018August 12, 2021 by Jean-Luc Aufranc (CNXSoft) - 30 Comments

Orange Pi RK3399 Development Board Launched for $109

Orange-Pi-RK3399-Board-Description-Large

Last Friday, I wrote there was already a decent choice of Rockchip RK3399 boards, and added AAEON RICO-3399 pico-ITX board to the list. I forgot about Shenzhen Xunlong’s own Rockchip RK3399 board that was spotted as early as last spring and was told Orange Pi RK3399 was now up for sale for around $110 (699 CNY) in Taobao. The board is now also for sale on Aliexpress for $109 plus shipping ($4.35 here), and the company has released the specifications, so we can have a better look at what the board has to offer. Orange Pi RK3399 specifications: SoC – Rockchip K3399 hexa-core big.LITTLE processor with two ARM Cortex A72 cores up to 2.0 GHz, four Cortex A53 cores, and an ARM Mali-T860 MP4 GPU with support for OpenGL 1.1 to 3.1 support, OpenVG1.1, OpenCL, and DX 11 System Memory – 2 GB DDR3 Storage – 16 GB eMMC flash, […]