openwrt News - Page 8 of 36 - CNX Software

June 1, 2023May 31, 2023 by Leo Zachary - 3 Comments

MangoPi mCore-R818 module powers CyberPad 3.1-inch handheld android “tablet”

mCore-R818 is the first time that MangoPi adopts the design combination of a core-lite module and a carrier board. As its name suggests, it is an AllWinner R818 SoM whose SoC integrates an Imagination PowerVR GE8300 GPU for UI rendering, can drive MIPI DSI, LVDS, and RGB displays, as well as cameras through a MIPI CSI interface, 8MP/5MP/2MP interfaces. The Allwinner R818 system-on-module powers a feature-rich carrier board as well as an upcoming Cyberpad Android “tablet” with a 3.1-inch display. MangoPi mCore-R818 The package design of the processor itself is small, so the MCore-R818 core board is only 3x3cm in size, but still contains four components with the Allwinner R818, the eMMC flash, LPDDR4 memory, and the AXP717 PMU. MangoPi provides two hardware configurations: 2GB DDR with 16GB eMMC flash, and 4GB DDR with 32GB eMMC flash. MCore-R818 Core Lite Specifications: SoC – Allwinner R818 CPU – Quad-core Arm Cortex-A53 […]

May 14, 2023June 30, 2023 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

GL.iNet Spitz AX review – Part 2: a router with 5G NR, WiFi 6, 2.5GbE, failover and load balancing

Gl.iNet Spitz AX review 5G failover testing

Earlier this month I introduced the GL.iNet Spitz AX (aka GL-X3000NR) router with 2.5GbE, WiFi 6, and 5G NR cellular connectivity listing the specifications, doing an unboxing, and going through the initial setup. I’ve now received a new SIM card for testing and installed it into the router to continue the review. 4G/5G cellular connectivity on Spitz AX router After powering the router, the SIM card was detected and showed a 5G connection, but quickly fell back to 4G as can be seen with the cyan icon in the screenshot below. Shortly after, I lost 4G data connectivity, and after a while, the modem was not detected at all. But after restarting the router, and clicking on the “Auto Setup” icon everything looked to be working fine and I was always on a 5G connection from “house 1”. You’ll notice an envelop icon on the top right corner of the […]

May 9, 2023May 10, 2023 by Jean-Luc Aufranc (CNXSoft) - 50 Comments

NanoPC-T6 Arm Linux SBC offers dual 2.5GbE, HDMI 2.1 outputs, HDMI 2.0 input, 2x M.2 sockets, and more

FriendlyELEC NanoPC-T6 is a feature-rich Rockchip RK3588 SBC with up to 16GB LPDDR4X RAM, 256GB eMMC flash, two HDMI 2.1 output ports, one HDMI 2.0 input port, dual 2.5GbE, two M.2 PCIe socket for storage or wireless, a mini PCIe socket and microSIM slot for 4G LTE connectivity, and more. The new NanoPC-T6 single board computer offered many more interfaces than the recent NanoPi R6S or R6C board based on the Rockchip RK3588S with fewer I/Os. As such, it would be suitable for a wider range of applications and FriendlyELEC says it is well suited to enterprise consumers who want to develop mini machine vision systems, and embedded systems hobbyists who want to explore and implement all sorts of prototypes. NanoPC-T6 specifications: SoC – Rockchip RK3588 CPU – Octa-core processor with 4x Cortex-A76 cores @ up to 2.4 GHz, 4x Cortex-A55 cores @ 1.8 GHz GPU – Arm Mali-G610 MP4 […]

May 6, 2023May 8, 2023 by Jean-Luc Aufranc (CNXSoft) - 38 Comments

Lichee Pi 4A RISC-V SBC takes on Raspberry Pi 4 with TH1520 processor

Lichee Pi 4A is a single board computer (SBC) powered by Alibaba T-Head TH1520 quad-core RISC-V Xuantie C910 processor @ 2.0 GHz with an Imagination GPU and a 4 TOPS NPU for AI that can compete against the Raspberry Pi 4 in terms of performance and features. We previously mentioned the Lichee Pi 4A (LPi4A) in our article about the Sipeed LM4A RISC-V system-on-module, but at the time we only had some benchmarks for the board and no photos and specifications about the SBC. Sipeed has now released photos, published detailed specifications, and is taking orders for the board. So let’s have a closer look. Lichee Pi 4A specifications against the ones for Raspberry Pi 4. The TH1520 used to be advertised at up to 2.5 GHz, but it seems to have now come down to 2.0 GHz. Software support will include Debian, OpenWrt, and Android which should then […]

May 4, 2023June 30, 2023 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

GL.iNet Spitz AX (GL-X3000NR) 5G NR WiFi 6 router review – Part 1: Specs, unboxing, and first boot

GL.iNet Spitz AX, also known as GL-X3000NR, is a compact 5G NR WiFi 6 router running OpenWrt 21.02 on a MediaTek Filogic 820 (TM7981A) dual-core Cortex-A53 processor coupled with 512MB DDR4 and 8GB eMMC flash, as well 2.5GbE and GbE interfaces, and a USB 2.0 port. The company sent us a Spitz AX router for evaluation, and in the first part of the review, we’ll go through the specifications, and do an unboxing and a teardown, before connecting it for a first boot. GL.iNet Spitz AX router specifications SoC – MediaTek MT7981A (Filogic 820) dual-core Arm Cortex-A53 processor @ 1.3 GHz System Memory – 512 MB DDR4 Storage – 8GB eMMC flash, MicroSD card slot up 1+ TB Networking 1x 2.5GbE WAN Ethernet port 1x Gigabit Ethernet LAN port Dual-band IEEE 802.11a/b/g/n/ac/ax WiFi 6 up to 574Mbps (2.4GHz), 2402Mbps (5GHz) RM520N-GL 5G cellular modem and 2x Nano SIM card slots […]

April 24, 2023April 25, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

EmbedFire LubanCat is a Rockchip RK3566/RK3568 SBC family with Raspberry Pi Zero/Model B, and other form factors

As I checked out Linux 6.3 changelog earlier this morning, I noticed the EmbedFire LubanCat 2 SBC in the Rockchip section, and having never heard of the EmbedFire company or LubanCat single board computers, I decided to have a closer look. EmbedFire is a company based in China, more exactly in DongGuan, that makes a range of LubanCat single board computers based on Rockchip RK3566 or RK3568 processors, some of which partially follow Raspberry Pi Zero or Raspberry Pi 3/4 Model B form factors, while others come with custom designs. LubanCat 2 SBC specifications: SoC – Rockchip RK3568 quad-core Arm Cortex-A55 @ up to 2.0 GHz with ARM Mali-G52 2EE GPU with support for OpenGL ES 1.1/2.0/3.2. OpenCL 2.0. Vulkan 1.1, 0.8 TOPS NPU System Memory – 1GB, 2GB, 4GB, or 8GB LPDDR4/LPDDR4X @ 1560 MHz Storage 8GB, 16GB, 32GB, 64GB or 128GB eMMC flash M.2 M-key socket (PCIe 3.0 […]

March 29, 2023 by Ian W MORRISON (Linuxium) - 9 Comments

iKOOLCORE R1 review – A quad 2.5GbE mini PC tested with Windows 11, Ubuntu 22.04, Proxmox

When I first saw the iKOOLCORE R1 I was fascinated that a mini PC of similar size to the smallest fully functional ones available (think Chuwi LarkBox, GMK NucBox or ECS LIVA Q Series) could be equipped with four 2.5 gigabit Ethernet (2.5GbE) ports. I approached iKOOLCORE who kindly provided an R1 for review and I’ve looked at performance running both Windows 11 and Ubuntu 22.04 and dabbled with using hypervisors on this mini PC through Proxmox virtual environment. iKOOLCORE R1 specifications iKOOLCORE list the R1 specifications on their website as: Of note are the ‘EC, FCC, RoHS’ certifications indicating both European conformity and approval for use in the US. Technically ‘EC’ refers to an ‘EC declaration of conformity’ which is not a certificate, however, the ‘EC declaration of conformity’ is called a ‘CE statement’ or ‘CE certificate’ which is why you often see this abbreviated as ‘CE’. The rest […]

March 25, 2023April 15, 2023 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

Getting Started with GL-S200 Thread Border Router kit

Getting Started GL-S200 Thread Border Router

Last week we checked out the hardware for the GL.iNet GL-S200 Thread Border Router kit with three nRF52840 Thread Dev Boards, and I’ve now had time to work with the kit, so I’ll report my getting started experience in the second part of the review. GL-S200 Initial Set Up I connected the WAN port to my Ethernet Switch itself connected to my modem router and the LAN port to my laptop, so I could access the web interface using the default IP address (192.168.8.1). The GL-S200 uses the same Admin Panel as other GL.iNet routers such as the Beryl AX router we reviewed at the beginning of the year. You’ll be greeted by a wizard to let you select the language and set a new password for the Admin Panel, and once you’re done you’ll have access to the familiar GL.iNet Admin Panel 4.x.x. After completing the wizard, the system […]