motor News - CNX Software - Embedded Systems News

July 31, 2024July 30, 2024 by Debashis Das - 3 Comments

STMicro EVLDRIVE101-HPD 1.9-inch motor driver board can drive 750W BLDC motors

ST EVLDRIVE101 HPD 750W Brushless DC motors Driver

STMicroelectronics has recently revealed the reference design for “EVLDRIVE101-HPD” their homegrown BLDC motor driver board that can drive up to a 750W BLDC motor. This compact 50 mm (1.9-inch) circular PCB combines STDRIVE101 3-phase, triple half-bridge gate-driver IC with an STM32G0 microcontroller, which is responsible for driving three-phase brushless motors. The driver board supports various motor-control strategies, including trapezoidal and field-oriented control (FOC), with both sensor’ed and sensorless rotor-position detection. Additionally, it has a wide operating voltage range of 5.5V to 75V and includes STL220N6F7 60V STripFET F7 MOSFETs, which have very low Rds(on) for high efficiency. Other features of the board include ultra-low power consumption in sleep mode, a single-wire debug interface, direct firmware update capability, and protection mechanisms such as under-voltage lockout, overtemperature protection, and cross-conduction prevention. All these features make this board suitable for applications like hairdryers, handheld vacuums, power tools, fans, drones, robots, and industrial equipment […]

March 1, 2024February 29, 2024 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

WeAct STM32G4 is a tiny board based on STMicro STM32G4 mixed-signal microcontroller

WeAct STM32G4 is a tiny development board based on a 170 MHz STMicro STM32G4 Arm Cortex-M4F mixed-signal microcontroller with DSP instructions and suitable for applications such as motor control, building automation, lighting, digital power meters, and more. Two versions of the board are offered one with an STM32G474CEU6 “Hi-resolution line” microcontroller equipped with 128KB RAM and 512KB flash, and the other with the lower-end STM32G431CBU6 “Access Line” MCU with just 32KB RAM and 128KB flash. The board also comes with a USB-C port for power and programming, three buttons, and two 24-pin headers. WeAct STM32G4 specifications: Microcontroller (one or the other) STMicro STM32G431CBU6 – Arm Cortex-M4F MCU @ 170 MHz with DSP instructions, 32KB RAM, 128KB flash, and math accelerator STMicro STM32G474CEU6 – Arm Cortex-M4F MCU @ 170 MHz with DSP instructions, 128KB RAM, 512KB flash, and math accelerator; high-resolution timer and complex waveform builder plus event handler (HRTIM) for […]

February 1, 2024January 31, 2024 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Renesas RA8T1 Cortex-M85 MCU targets motor control applications

It took a while before Renesas released its first Arm Cortex-M85 microcontroller (RA8M1) in October 2023, but the company has now launched the RA8T1 Cortex-M85 MCU for motor control just a few weeks after announcing the RA8D1 for HMI applications. The RA8T1 group is the third Cortex-M85 microcontroller family from Renesas with a feature set optimized for motor control and leveraging machine learning through Arm Helium technology and a DSP for predictive maintenance requirements for motors. Renesas RA8T1 key features and specifications: MCU core – Arm Cortex-M85 clocked at 480 MHz with Helium MVE (M-Profile Vector Extension) with 32KB I/D caches, 12KB data flash Memory & Storage 1MB SRAM including 128KB TCM 1MB to 2MB Flash memory 2x SD/MMC host interfaces (SDHI) Communication interfaces Ethernet MAC with DMA USB – 1x USB 2.0 Full Speed interface 2x CAN-FD Up to 6x SCI (UART, Simple SPI, Simple I2C) 2x SPI up […]

January 31, 2024January 31, 2024 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

NXP launches MCX A14x and MCX A15x Arm Cortex-M33 MCUs along with FRDM-MCXA153 development board

NXP has just announced the launch of the MCX A series Arm Cortex-M33 microcontrollers with the MCX A14x running up to 48 MHz and the MCX A15x running up to 96 MHz. The devices support up to 128KB flash and 32KB SRAM, offer I2C, I3C, and SPI sensor interfaces, and integrate support for BLDC/PMSM motor control. NXP first unveiled the NXP MCX general-purpose Arm MCU family with 30 times faster machine learning at Embedded World 2022, but at the time we had limited information although four series were planned with the MCX N Advanced series up to 250 MHz, the MCX A essential series up to 96 MHz, the MCX W Wireless series with Bluetooth LE, and the MCX L Low-power series. The MCX A series has just been launched, and the high-end MCX N also has its own product page with the N94x and N54x variants. We’ll focus on […]

November 20, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

SaraKIT – An Raspberry Pi CM4 board with ChatGPT-based voice control, motor control, and plenty of sensors (Crowdfunding)

SaraKIT is a carrier board for the Raspberry Pi CM4 system-on-module with BLDC motor controllers and a range of sensors for robotics, support for ChatGPT-based voice control through three microphones and a ZL38063 audio chip, and two MIPI CSI connectors for cameras. The versatile board can be used for voice-controlled products, robots, home automation systems, and interfacing with smart home or office devices. The company also developed various demos such as a Smartphone-controlled LEGO RC car, a self-balancing LEGO robot, a pan-and-tilt camera, various AI demos using MediaPipe such as face tracking and object detection, as well as audio demos using ChatGPT, Alexa, and/or Google Home. SaraKIT specifications: Support system-on-modules – Raspberry Pi Compute Module 4 (CM4) with future CM5 compatibility. MCU – Microchip dsPIC33 16-bit microcontroller with 32 KB SRAM for motor control and LSM6DS3TR sensor Audio Microchip ZL38063 (previously MicroSemi) audio processor for microphone arrays. 3x Knowles SPH0655 […]

November 4, 2023November 4, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Makeblock mBot Neo robot review with Smart World Add-on Pack

MakeBlock mBot Neo, also known as mBot2, is an educational robot that builds upon the previous generation mBot1 robot, and the company has sent us a review sample, following our earlier review of the Ultimate 2.0 10-in-1 educational robot kit, along with the Smart World Add-on Pack. The mBot Neo features a new ESP32-based CyberPi control board with WiFi connectivity for IoT and AI support. The robot is also equipped with a 2nd generation Ultrasonic sensor with improved object detection accuracy and status indicator, a built-in 4-ch RGB line sensor that can detect colors, as well as a new drive motor that comes with an encoder for more precise motion control. The mBot Neo robot kit is expandable with metal parts from other Makeblock models, mBuild modules and various electronic modules can be added making it also possible to build custom robots with third-party structural parts. The mBot Neo robot […]

September 22, 2023September 22, 2023 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

AMD Kria K24 Zynq Ultrascale+ system-on-module targets motor control and DSP applications

The AMD Kria K24 System-on-Module (SOM) with a custom-built Zynq UltraScale+ MPSoC and the KD240 Drives Starter Kit are designed for the development of cost-sensitive industrial and commercial edge applications. The new Kria K24 is about half the size of a credit card and uses half the power of the larger, but connector-compatible, Kria K26 SOM that was introduced in 2021 for computer vision applications when the company was still known as Xilinx. That means existing K26 carrier boards can be reused with the Kria K24 SOM without modifying the PCB, but note there’s only one 240-pin connector on the new module, plus an extra 40-pin connector. AMD Kria K24 specifications: MPSoC – Custom-built Zynq Ultrascale+ XCK24 Quad-core Arm Cortex-A53 processor up to 1.3 GHz Dual-core Arm Cortex-R5F real-time processor up to 533 MHz Mali-400 MP2 GPU up to 600 MHz FPGA fabric with 154K logic cells AMD Deep Learning […]

August 28, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

SemiDrive D9-Pro (D9360) Arm Cortex-A55/R5 processor powers industrial CPU module for motor control

MYD JD9360 SemiDrive D9 Pro Development Board

MYiR MYC-JD9360 is a CPU Module powered by SemiDrive D9-Pro (D9360) processor with six Arm Cortex-A55 application cores, a dual-core lock-step Cortex-R5 real-time core along with a PowerVR GPU, 4Kp30 H.265/H.264 VPU and a 0.8 TOPS NPU, and designed for motion control and industrial applications. The MYC-JD9360 CPU module also comes with 2GB LPDDR4, 16GB eMMC flash, 16MB QSPI Flash, 256Kbit EEPROM, and exposes I/Os such as PCIe 3.0, USB 3.0, CAN FD, and TSN-enabled Gigabit Ethernet through a 314-pin MXM connector. The company also provides the MYD-JD9360 development board to quickly get started with the module and evaluate the solution. MYiR MYC-JD9360 CPU module with SemiDrive D9-Pro SoC Specifications: SoC – SemiDrive D9-Pro (D9360) CPU Application – Hexa-core Arm Cortex-A55 processor @ 1.6 GHz Real-time – Dual-core lock-step Cortex-R5 cores @ 800MHz GPU – Imagination PowerVR 9XM GPU @ 100 GFLOPS VPU – 4Kp30 H.265/VP8/VP9 video decoder, 4Kp30 H.264 […]