micropython News - Page 8 of 27 - CNX Software

October 4, 2023October 3, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Inkplate 4 TEMPERA ePaper display supports ESPHome, Arduino, and MicroPython (Crowdfunding)

Years after years, Soldered Electronics keeps on churning out new ESP32-powered ePaper displays and the latest model is the Inkplate 4 TEMPERA with a recycled 3.8-inch e-paper touchscreen with 600×600 resolution and plenty of sensors and features for a device of that size. The InkPlate 4 TEMPERA comes with a frontlight, a gyroscope, an accelerometer, temperature, humidity, air quality, and gesture sensors, Wi-Fi and Bluetooth connectivity, a built-in battery, and a low-power operating mode. Inkplate 4 TEMPERA specifications: Wireless module – ESP32-WROVER-E with ESP32 dual-core microcontroller with Wi-Fi 4 & Bluetooth 4.0 connectivity Memory – 8MB PSRAM Storage – 4MB flash PCB antenna Storage – MicroSD card slot Display (ED038TH2) 3.8-inch 3-bit grayscale (black, white, and six shades of gray) ePaper display with 600 x 600 pixels resolution Refresh rate 0.18s partial refresh rate in 1-bit (B&W) mode 0.86s full refresh mode in either 1-bit or 3-bit modes Multi-point touchscreen […]

September 5, 2023September 4, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

STARLIGHT – A Raspberry Pi RP2040 board for rockets

STARLIGHT Raspberry Pi RP2040 rocket board

Circuit Wizardry’s STARLIGHT is a rocket control board based on Raspberry Pi RP2040 microcontroller and designed for small 75mm model rockets. The board features rocket control-specific I/Os such as Igniter and Ejection pins each connected to a MOSFET, two headers for 5V servos, plus some sensors and 3.3V or 5V GPIOs for expansion. STARLIGHT specifications: Microcontroller – Raspberry Pi RP2040 dual-core Arm Cortex-M0+ MCU @ 133 MHz with 264KB SRAM Storage – 16MB flash for firmware and flight data USB – 1x Micro USB port for programming Rocket control Igniter via 2-pin terminal block and AO3400 MOSFET (pulse current up to 30A) used with ignition systems to automatically light your engine. Ejection via 2-pin terminal and AO3400 MOSFET Servo control 2x 3-pin servo outputs for optional thrust loop vector control interface (X Axis and Y axis on board) Level shifter to allow the use of 5V servos with the 3.3V […]

August 3, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

eModGATE Moduino X0 – An ESP32-based industrial IoT controller with battery support

eModGate X0 ESP32 industrial IoT controller

TECHBASE eModGATE Moduino X0 is an industrial IoT control based on a choice of ESP32 modules from Espressif and Pycom, equipped with a battery slot for remote installations, and various interfaces to connect sensors or actuators via RS232, RS485, and/or digital I/Os. We first wrote about TECHBASE Moduino-X series ESP32 IoT endpoints almost six years ago with the X1 and X2 models, but since then the company has added more models such as the large X3 and X4 devices with more I/Os, and the new entry-level Moduino X0 that’s similar to the X1, but with battery support instead of a supercapacitor. eModGATE Moduino X0 specifications: ESP32 wireless module/board options ESP32-WROVER with ESP32 dual-core Tensilica LX6 processor @ 240 MHz, 8MB PSRAM, 4MB or 16MB SPI flash Pycom WiPy 3.0 with 4MB RAM, 8MB Flash Pycom SiPy with 512kB RAM, 4MB Flash, Sigfox Pycom LoPy with 4MB RAM, 8MB Flash, Wi-Fi/BT4.2, […]

July 29, 2023 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

12 Euros ESP32-S3-DevKit-LiPo board runs Linux 6.3

Olimex ESP32-S3-DevKit-LiPo is a new open-source hardware ESP32-S3 board with 8MB flash, 8MB PSRAM, as well as LiPo battery and JTAG support that can run Linux 6.3, or the more traditional Arduino or MicroPython firmware. The board is based on the ESP32-S3-WROOM-1-N8R8 module, features two USB-C ports for power, programming, and JTAG debugging, plenty of expansion with two rows of I/Os plus a pUEXT connector, Reset and Boot buttons, and a couple of LEDs. ESP32-S3-DevKit-LiPo specifications: Wireless module – Espressif ESP32-S3-WROOM-1-N8R8 with SoC – ESP32-S3 dual-core LX7 microprocessor @ up to 240 MHz with Vector extension for machine learning, WiFi 4 & Bluetooth 5 LE/Mesh Memory – 8MB OSPI PSRAM Storage – 8MB QSPI flash PCB antenna Dimensions – 25.5 x 18.0 x 3.1 mm USB 1x USB Type-C OTG port also used for JTAG/Serial 1x USB Type-C port for USB-serial programming and power Expansion 2x 22-pin GPIO headers pUEXT […]

July 26, 2023July 26, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

RP2 Nano is a $6.6 Raspberry Pi RP2040 board with Arduino Nano form factor

ArtronShop RP2 Nano board features the Raspberry Pi RP2040 microcontroller in the Arduino Nano form factor in a way that’s much cheaper than the official Arduino Nano RP2040 Connect board. That’s possible because Thailand-based AtronShop did not include all the bells and whistles such as WiFi and Bluetooth connectivity, sensors, and used a smaller flash. So the RP2 Nano basically offers the same I/Os and features as the Arduino Nano, but the Microchip ATmega328 8-bit AVR microcontroller gives place to the more powerful Raspberry Pi RP2040 dual-core Cortex-M0+ MCU plus 2MB flash, and the board also adds an extra Grove connector for expansion. RP2 Nano specifications: MCU – Raspberry Pi RP2040 dual-core Cortex M0+ microcontroller @ 133 MHz with 264 kB of embedded SRAM Storage – 2MB SPI flash USB – 1x USB Type-C OTG port for power, data, and programming Expansion Arduino Nano headers (2x 15-pin headers) Up to […]

July 24, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

ButtonBoard is a 3cm round WiFi IoT board with BME280 and IMU sensors (Crowdfunding)

ButtonBoard round shap ESP8285 WiFi IoT board

ButtonBoard is a tiny round-shaped board based on the ESP-01F WiFi IoT module (ESP8285), equipped with a BME280 air pressure, humidity, and temperature sensor, an IMU sensor, and designed for wearables electronics projects. ButtonBoard specifications: Wireless module – ESP-01F module with ESP8285 Tensilica L106 microcontroller @ 80/160 MHz with 2.4GHz WiFi connectivity, PCB antenna; package: 11 x 10 mm USB – Micro USB port Sensors Bosch Sensortec BME280 pressure, temperature, and humidity sensor, and altimeter. IMU sensor Expansion – Through holes for up to 10x GPIOs, I2C, SPI, USART Misc – Reset button Power Supply – 5V via micro USB port; onboard power management Dimensions – About 3cm diameter The ButtonBoard can be programmed with the Arduino IDE via USB or WiFi, MicroPython, Lua, and Scratch, and they also mention support for ChatGPT through the current API, but I could not find any code samples at this time. They do […]

July 18, 2023July 18, 2023 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

ESP32-S3 based Arduino Nano ESP32 board supports Arduino and MicroPython programming

The Arduino Nano ESP32 is an ESP32-S3-based WiFi and Bluetooth microcontroller board designed for IoT applications for hobbyists and enterprise use cases. The new Nano board comes with 8 MB PSRAM and 16 MB flash storage and can be programmed with either the Arduino or MicroPython languages. It’s not the first ESP32 board from Arduino, as the Nano RP2040 Connect pairs a Raspberry Pi RP2040 MCU with an ESP32 module from u-Blox and the just-released Arduino UNO R4 WiFi marries a Renesas RA4M1 Arm Cortex-M33 MCU with an ESP32-S3-MINI-1 module. But the Arduino Nano ESP32 is different since it’s the first ESP32 board from Arduino where the Espressif chip is the only microcontroller onboard and handles both wireless connectivity and GPIOs. Arduino Nano ESP32 specifications: Wireless module – u-Blox NORA-W106-10B with MCU – ESP32-S3 dual-core Xtensa LX7 microcontroller @ up to 240 MHz with vector extensions, 512KB SRAM, 384KB ROM, […]

July 12, 2023July 12, 2023 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

smolOS brings a Linux-like command line interface to ESP8266 microcontroller

smolOS (pronounced small OS) is an open-source, lightweight MicroPython program that implements a POSIX-style (Linux-like) command line interface for the ESP8266 WiFi microcontroller. Krzysztof Jankowski (w84death) designed smolOS to be easy to use, allowing the listing and removing of files and also including the smolEDitor which, as its name implies, is a simple text editor. There are currently eight commands with the familiar ls, cat, and rm, plus ed to launch the text editor, welcome to show the welcome screen above, cls to clear the screen, mhz to set the processor speed to 80 or 160 MHz, and info to display some hardware and software information. The project looks to be a work in progress, and the developer highlights the editor is at the alpha stage of development, so more features may be implemented over time by Krzysztof himself or by the community of developers. I also assume other microcontrollers […]