low power News - Page 18 of 41 - CNX Software

April 4, 2023August 5, 2024 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

ESP32-S3 based 1.28-inch round touchscreen display supports Arduino programming

ESP32-S3 Round Display 1.28-inch touchscreen

Makerfabs “ESP32-S3 Round SPI TFT with Touch 1.28″ is a small ESP32-S3 with a 1.28-inch round color touchscreen display, a microSD card, support for USB and battery power, and two “Mabee” extension connectors. The board joins other ESP32-S3 round display boards such as the Lilygo T-RGB board or Seeed Studio’s Round Display for XIAO, but with a thinner design, and a square PCB with trimmed corners instead of a round PCB like the other two. ESP32-S3 Round SPI TFT with Touch 1.28″ (E32S3128GC) specifications: Wireless MCU – Espressif Systems ESP32-S3R8 dual-core Tensilica LX7 microcontroller @ 240 MHz with vector extension, 512KB SRAM, 8MB PSRAM, Wi-Fi 4 & Bluetooth 5.0 dual-mode (Classic + BLE) connectivity Flash – 128 Mbit (16MB) W25Q128JV SPI flash, microSD card slot Display – 1.28-inch round LCD with 240×240 resolution (GC9A01 SPI driver), touchscreen controller (CST816S) USB – 1x USB Type-C port Expansion 1x 4-pin Mabee I2C […]

March 31, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

STMicro STLINK-V3PWR debugging & programming probe supports power measurement

STMicro STLINK-V3PWR is a new in-circuit debugging and programming probe made for STM32 microcontrollers and that is said to provide accurate power measurement. The probe is especially useful for battery power IoT and wireless applications and is able to measure current values from nanoamps up to ~500mA with up to ±0.5% accuracy. The STLINK-V3PWR can also power the target over a single USB cable up to 2A. STMicro STLINK-V3PWR key features and specifications: 1‑Quadrant source measurement unit: Programmable voltage source from 1.6 to 3.6 V Output current rating 500 mA with over-current protection (OCP) at 550 mA Programmable sampling rate from 1 SPS to 100 kSPS Dynamic measurement 100 nA to 550 mA current 160 nW to 1.65 W power measurements 50 kHz bandwidth 1.6 MHz acquisition / 2% accuracy Compatible with EEMBC ULPMark tests Auxiliary output voltage source from 1.6 to 3.6 V under up to 2 A (no current measurement, OCP at 2.5 A) Debugging of […]

March 29, 2023March 29, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

XIAO ESP32S3 board gets some senses with a camera and microphone module, plus a round touchscreen display

Last week, we wrote about the new XIAO ESP32S3, a tiny ESP32-S3 board from Seeed Studio. The company has now launched the XIAO ESP32S3 Sense adding a camera and microphone module connected through a board-to-board connector, as well as the Round Display for XIAO that can help people easily create wearable devices with a touchscreen based on any board from the XIAO family. XIAO ESP32S3 Sense XIAO ESP32S2 Sense specifications: Wireless MCU – Espressif Systems ESP32-S3R8 dual-core Tensilica LX7 microcontroller @ 240 MHz with 512KB SRAM, 8MB PSRAM, Wi-Fi 4 & Bluetooth 5.0 dual-mode (Classic + BLE) connectivity Storage – 8MB SPI flash, microSD card slot Antenna – External u.FL antenna USB – USB Type-C port for power and programming Camera – OV2640 camera sensor up to 1600×1200 resolution Audio – Built-in digital microphone Expansion I/Os 2x 7-pin headers with 1x UART, 1x I2C, 1x SPI, 11x GPIO (PWM), 9x […]

March 27, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Tiny RASynBoard combines Renesas RA6M4 MCU with Syntiant NDP120 ML accelerator, WiFi & BLE module, and some sensors

Avnet RASynBoard is a tiny board that packs a lot of features in a 30x25mm form factor with a Renesas RA6M4 Cortex-M33 microcontroller, a Syntiant NDP120 Neural Decision Processor, a Renesas (Previously Dialog Semi) DA16600 Wi-Fi 4 & Bluetooth 5.1 combo module, and a 6-axis inertial measurement unit (IMU) and digital microphone from TDK. The RASynBoard is offered as part of an EVK with the Core Board described above plus an IO board with headers, a Pmod connector, a MikroE Shuttle Click header, a microSD card slot for storage, and a built-in debugger, plus two buttons and an RGB LED. RASynBoard specifications: Main microcontroller – Renesas RA6M4 Arm Cortex-M33 microcontroller @ 200 MHz with 1 MB flash memory, 256 KB SRAM ML accelerator – Syntiant NDP120 Neural Engine based on Syntiant Core 2 Deep Neural Network, Arm Cortex M0 and HiFi 3 DSP Wireless module – Renesas DA16600 2.4 […]

March 17, 2023March 17, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

WisDuo RAK11720 LoRaWAN & Bluetooth LE module features Ambiq Apollo3 Blue low-power MCU

RAKwireless WisDuo RAK11720 is a LoRaWAN and Bluetooth LE (module) equipped with Ambiq Apollo3 ultra-low-power BLE 5.0 microcontroller and a Semtech SX1262 LoRa transceiver. The Wisduo RAK11720 is pin-to-pin compatible with the STM32WL-based Wisduo RAK3172 LoRaWAN module, and provides an easy upgrade path for IoT applications that require Bluetooth LE connectivity and more memory. WisDuo RAK11720 specifications: MCU – Ambiq Apollo3 Blue AMA3B1KK-KBR-B0 Arm Cortex-M4F microcontroller locked at up to 96 MHz with 1MB flash, 348 SRAM, Bluetooth LE 5.0, and an active power consumption of less than < 6 μA/ MHz LoRa Semtech SX1262 sub-GHz radio transceivers LoRaWAN 1.0.3 specification compliant Supported bands: EU433, CN470, IN865, EU868, AU915, US915, KR920, RU864, and AS923-1/2/3/4 LoRaWAN activation via OTAA/ABP LoRa Point-to-Point (P2P) communication Long-range – greater than 15 km with optimized antenna Antennas – 2x IPEX antenna connectors or RF pads for LoRa and Bluetooth I/O expansion – UART, I2C, SPI, […]

March 16, 2023 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Renesas introduces 100 MHz RA4E2 and 200 MHz RA6E2 Arm Cortex-M33 MCUs for wearables, sensors, appliances

Renesas Electronics has added two new groups to its 32-bit RA family of microcontrollers (MCUs) with the 100 MHz RA4E2 and 200 MHz RA6E2 Arm Cortex-M33 microcontrollers designed for “high-performance applications” in small packages such as sensing, gaming, wearables, and appliances. The new microcontrollers are equipped with 40 KB SRAM, 128 KB or 256 KB flash, and integrate various on-chip interfaces such as CAN FD, USB, QSPI, SSI, and I3C interfaces to offer an easy upgrade path for products based on other members of the Renesas RA Family. Renesas RA4E2 MCU group Both the RA4E2 and the RA6E2 are the most cost-effective microcontroller groups of the RA family with integrated CAN FD, with the RA4E2 group especially well-suited to cost-sensitive applications and other systems requiring relatively high performance, low power consumption, and/or small package size. RA4E2 key features: CPU – Arm Cortex-M33 core with TrustZone @ up to 100 MHz […]

March 13, 2023March 12, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Aspinity AB2 AML100 Arduino Shield supports ultra-low-power analog machine learning

Aspinity AB2 AML100 analog machine learning Arduino Shield

Aspinity AB2 AML100 is an Arduino Shield based on the company’s AML100 analog machine learning processor that reduces power consumption by 95 percent compared to equivalent digital ML processors, and the shield works with Renesas Quick-Connect IoT platform or other development platforms with Arduino Uno Rev3 headers. The AML100 analog machine learning processor is said to consume just 15µA for sensor interfacing, signal processing, and decision-making and operates completely within the analog domain offloading most of the work from the microcontroller side that can stay its lowest power state until an event/anomaly is detected. Aspinity AB2 AML100 Arduino Shield specifications: ML chip – Aspinity AML100 analog machine learning chip Software programmable analogML core with an array of configurable analog blocks (CABs) with non-volatile memory and analog signal processing Processes natively analog data Near-zero power for inference and events detection Consumes <20µA when always-sensing Reduces analog data by 100x Supports up […]

March 8, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Toradex Verdin AM62 – An entry-level Sitara AM623/AM625 SoM for Industry 4.0, Smart Cities, Healthcare…

Toradex Verdin AM62 is a system-on-module based on Texas Instruments AM62 Cortex-A53/M4 processor with up to 1GB LPDDR4 RAM and 8GB eMMC flash that is the most affordable system-on-module from the company’s Verdin family. The module also comes with a Gigabit Ethernet PHY and an optional WiFi 5 and Bluetooth 5 module and exposes various interfaces through its edge connector such as dual Gigabit Ethernet, MIPI DSI and LVDS display interfaces, a MIPi CSI-2 camera interface, and CAN FD, and more. Toradex Verdin AM62 specifications: SoC – Texas Instruments Sitara AM623/AM625 with up to 4x Arm Cortex-A53 cores @ 1.4GHz, 1x Arm Cortex-M4F @ 400MHz, optional 3D GPU with support for OpenGL 3.x/2.0/1.1 + extensions, Vulkan 1.2 (AM625 only) System Memory – Up to 1GB LPDDR4 (16-bit) Storage – Up to 8GB eMMC flash Networking Texas Instruments DP83867IRRGZR industrial-grade Gigabit Ethernet PHY Optional Wi-Fi 5 and Bluetooth 5 module (AzureWave […]