kickstarter News - Page 30 of 46 - CNX Software

August 25, 2016 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Dot is a Location Aware Bluetooth Beacon Used as a Digital Post-it, for Home Automation, and More (Crowdfunding)

Dot physical push notification is another Bluetooth beacon, but the company – Iota Labs – has designed and promote it in a location aware device that gets triggered when you move in a specific area with your smartphone. For example, somebody can leave a dot with a message such as “remember to take the trash out” in the kitchen, and once you walk pass you’ll receive a notification, or you can use a dot to automatically turn on the light if you enter a room at night. The full technical specifications have not been made available but here’s what we know: MCU – Nordic Semi nRF51822 (or similar) ARM SoC with Bluetooth radio Connectivity – Bluetooth 4.0 LE with a range up to around 45 meters Misc – RGB LED Battery – Replaceable battery good for 6 months to one year Android and iOS apps will allow your to configure […]

August 24, 2016August 27, 2016 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

ReSpeaker WiFi IoT Board is Designed for Voice Interaction (Crowdfunding)

More and more devices are supporting voice interaction nowadays from your smartphone to devices like Amazon Echo, but so far, I had not seen development boards specifically designed for that purpose, and that’s exactly what Seeed Studio ReSpeaker board does by combining audio capabilities, WiFi connectivity, and I/O headers. ReSpeaker Core board specifications: WiFi Module – Acsip AI7688 Wi-Fi 802.11 b/g/n module based on Mediatek MT7688 MIPS SoC Storage – micro SD card slot USB – 1x micro USB port for programming and power Audio – 3.5mm AUX port, WM8960 audio codec, 2-pin header for external speakers Expansion – 2x 8-pin expansion headers for I2C, GPIO and USB 2.0 host connected to MT7688, built-in microphone. MCU – Atmel ATMega32U4 @ 16 MHz Misc – 12x RGB LEDs, 8x touch sensors, 3 push buttons Power Supply – 5V DC Dimensions – 70mm diameter Weight – 70 grams The board runs OpenWrt, […]

August 18, 2016August 18, 2016 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Teensy 3.5 & 3.6 Boards Feature NXP Kinetis K64 & K66 MCUs (Crowdfunding)

Paul Stoffregen has been making Teensy USB MCU development boards since 2008, and has just launched the latest Teensy 3.5 & 3.6 boards powered by NXP (previously Freescale) Kinetis K64 & K66 ARM Cortex-M4 MCUs with a micro USB port for power and programming, a micro SD slot, and several I/Os. Boards specifications: MCU Teensy 3.5 (T3.5) – NXP Kinetis K64 ARM Cortex M4 MCU @ 120 MHz with FPU, 512KB flash, 192 KB RAM, 4K EEPROM Teensy 3.6 (T3.6) – NXP Kinetis K66 ARM Cortex M4 MCU @ 180 MHz with FPU, 1MB flash, 256KB RAM, 4K EEPROM Storage – micro SD card port USB – 1x USB Full Speed (12 Mbit/sec) Port; T3.6 only: 480 Mbit/sec host port Connectivity – 10/100M Ethernet mac 62x I/O Pins (42 breadboard friendly) 25x Analog Inputs to 2 ADCs with 13 bits resolution 2x Analog Outputs (DACs) with 12 bit resolution 20x […]

July 27, 2016July 27, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

RuuviTag Open Source Bluetooth & NFC Sensor Beacon is Based on Nordic Semi nRF52832 SoC (Crowdfunding)

I’ve recently featured Puck.js Bluetooth 4.2/5.0 Beacon on CNX Software, but there’s another similar option with RuuviTag, also powered by the latest Nordic Semi nRF52832 ARM Cortex-M4 SoC, and RuviiTag+ version that includes multiple sensors: 3-axis accelerometer, and temperature, humidity, and pressure sensor. RuuviTag & RuuviTag+ specifications: SoC – Nordic Semi nRF52832 ARM Cortex-M4F micro-controller @ 64 MHz with Bluetooth Smart and NFC Connectivity Bluetooth 4.2 Smart, Bluetooth 5.0 Ready; over 500 meters line of sight range (with -4dBm power); up to 1.4 km with +4 dBm Integrated NFC antenna Expansion – 8x through holes with 6x GPIOs, and 2x power signals Sensors On-chip temperature sensor RuuviTag+ – Bosch BME280 environmental sensor (pressure, humidity, and temperature), STMicro LIS2DH12 3-axis accelerometer Misc – User/reset button, 2x LEDs, 10-pin SWD debug connector Battery – CR2450 / CR2477 battery up to 10 years depending on application Dimensions – N/A Temperature Range – -40°C […]

July 26, 2016July 26, 2016 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Bagel is a Smart Bluetooth Tape Measure Compatible with Android and iOS Phones (Crowdfunding)

The tape measure is a pretty simple tool allowing you to measure length, and I assume most people will write results on a piece of paper. Battery powered Bagel tape measure changes that as it allows measurements with a string, through a wheel, or an ultrasonic sensors, store the data in its internal memory with voice to text memo, and also sends back data over Bluetooth to your smartphone. Bagel Labs tape measure specifications: Three measure modes – string (up to 3 meters), wheel (up to 10 meters), or ultrasonic sensor (0.3 to 5 meters) Storage – 32 MB flash for up to 100 measurements and voice memo (Both metric and imperial units supported) Connectivity – Bluetooth 4.0 LE Audio – Microphone for voice to text recording Display – 0.96″ OLED display; 128×96 resolution USB – 1x micro USB port for charging Misc – laser pointer for ultrasonic measurement; save […]

July 22, 2016July 22, 2016 by Jean-Luc Aufranc (CNXSoft) - 16 Comments

Superbook turns your Android smartphone in to a laptop for $99 (Crowdfunding)

Using a laptop shell with a smartphone is not a new concept, but products like Motorola Lapdock were eventually phased out. But some people think there’s a market here, that Lapdock may just have been ahead of it time, and with smartphone faster than ever, it now makes more sense to use them as laptop too. That’s probably why the Superbook, allowing you to connect your smartphone to a larger screen and keyboard via a USB OTG cable, has just launched on Kickstarter. Superbook specifications: Display – 11.6″ LCD display; 1366×768 resolution Keyboard – QWERTY keyboard with multi-touch trackpad USB – USB type-C port (smartphone with micro B USB are also supported via an adapter) Misc – Android-specific navigation keys (Home, Back, Menu, Recent) Custom Charging Port w/ Standard US charger Battery – Good for 8 hours or more Dimensions – 19.3 x 28.7 x 1.8cm Superbook also charges your smartphone. […]

July 20, 2016 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

Onion Omega2 is a $5 Linux WiFi IoT Board (Crowdfunding)

Onion Omega board was first introduced in 2015. The tiny OpenWrt Linux board featured an Atheros AR9331 processor with GPIO headers, and various baseboards and add-ons. The company has now launched a Kickstarter campaign for the second versions – Omega2 & Omega2 Plus – with a faster processor @ 580 MHz, compatible with docks and add-ons boards used for Omega, and a much lower price with $5 for the Omega2, and $9 for Omega2 Plus with more storage and memory. Omega2 & Omega2 Plus specifications: WiSoC – 580 MHz processor, possibly Mediatek MT7688 MIPS processor used in LinkIt Smart 7688 System Memory Omega2 – 64MB Omega2 Plus – 128MB Storage Omage2 – 16MB flash Omega 2 Plus – 32MB flash + micro SD slot Connectivity Built-in – 802.11 b/g/n WiFi with on-board and external antenna support Via add-on boards – Bluetooth 4.0 LE, GPS, and 2G/3G Expansion – 15x GPIO, […]

July 13, 2016July 14, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Puck.js Bluetooth 5.0 Ready Beacon is Programmable with JavaScript (Crowdfunding)

I first found out about Bluetooth LE tags in 2012 with SticknFind project, and since then many other companies have designed their own Bluetooth beacon mostly to find objects such as your keys or pets. Puck.js is also a Bluetooth 4.2 LE beacon, but has many more features including compatibility with the upcoming Bluetooth 5.0 standard, and some GPIOs programmable with JavaScript (Espruino implementation), and corresponding visual programming editor. Puck.js hardware specifications: Bluetooth Smart SoC – Nordic Semi nRF52832 ARM Cortex-M4F micro-controller @ 64 MHz Connectivity Bluetooth 4.2 LE/smart, Bluetooth 5.0 Ready; up to 80 meters range in open space On-chip NFC support Expansion – 8x through holes with 6x GPIOs, and 2x power signals Sensors – MAC3110 magnetometer, on-chip temperature sensor Misc – 1x tactile button, 4x LEDs (R, G, B, IR) Battery – CR2032 210mAh battery good for about a year (application dependent) Dimensions – 35mm diameter, 10mm […]