kickstarter News - Page 18 of 48 - CNX Software

June 16, 2020August 24, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

CrowPi2 Raspberry Pi 4 Laptop Doubles as Electronics Learning Kit (Crowdfunding)

CrowPi2 Raspberry Pi 4 Laptop with Detachable Keyboard

CrowPi portable learning kit for Raspberry Pi 3 B+ and Pi Zero boards was launched in 2018. It comes with a 7″ display, several sensors, buttons, a breadboard, and more all packed in a small suitcase. Elecrow has now started a new crowdfunding campaign on Kickstarter to fund the second generation portable electronics learning kit: CrowPi2 which looks much more like a laptop than a suitcase found in the first model thanks to a large display, and a detachable keyboard placed on top of the electronic prototyping/learning area. It’s also more powerful thanks to the latest Raspberry Pi 4 SBC. CrowPi2 specifications: Compatible Raspberry Pi boards – Raspberry Pi 3B/B+, Raspberry Pi 4 Display – 11.6-inch 1920×1080 IPS screen Camera – 2MP camera Audio – Built-in microphone and stereo speaker; 3.5mm audio jack Keyboard – 2.4GHz detachable wireless keyboard (QWERTY only) with touchpad Sensors and Modules under the keyboard: Displays […]

June 7, 2020June 6, 2020 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

STM32 based Indoor Air Quality Sensor Connects to Raspberry Pi or Arduino (Crowdfunding)

Indoor Air Quality Sensor Raspberry Pi Arduino

Even before the COVID-19 lockdown, people spent most of their time indoors (around 90% according to some studies), so it’s important to monitor air quality and other metrics like light and sound levels in our homes, workplaces, schools, cars, etc… Metriful Sense indoor environment monitor does just that by reporting multiple metrics such as temperature, humidity, particle concentration, etc… over I2C to microcontroller or processor boards such as Arduino or Raspberry Pi. Sense hardware specifications: MCU – STMicro STM32G071KB Arm Cortex-M0+ microcontroller @ 64 MHz with 128 KB Flash, 36 KB SRAM Sensors Bosch Sensortec BME680 4-in-1 air quality sensor with relative humidity, barometric pressure, ambient temperature, and gas (VOC). Vishay VEML6030 ambient light sensor Knowles SPH0645LM4H-B MEMS microphone Optional – Shinyei PPD42 particle sensor unit I/Os – 10-pin unpopulated header with air particles sensor input, light and sound interrupt outputs, I2C, VPU pin for 3.3V/5V selection, GND, VDD, VIN […]

May 21, 2020May 21, 2020 by Jean-Luc Aufranc (CNXSoft) - No Comments

MARK AI Robot Kit Aims to Teach AI & Robotics to 12+ Years Old (Crowdfunding)

We’ve written about Kendryte K210 RISC-V AI processor, and Sipeed M1 module several times including in our getting started for Maixduino and GroveAI HAT boards for low-power AI inference such as object recognition or face detection using Arduino and Micropython programming. Shenzhen-based Tinkergen, a STEM Education owned by Seeed Studio, has now leveraged the low-cost processor to design MARK AI robot kit, where MARK stands for Make A Robot Kit, in order to processor an educational AI Robotics platform for children ages 12 years old and more. MARK will ship as a kit with the main parts and components including a chassis, a cover, two wheels, stepper motors, a pan-tilt camera with K210 processor, a 2.4″ LCD display, Grove & Arduino compatible MARKduino interface board, some sensors, and six AA batteries. Tinkergen offers pre-trained model to recognized objects like humans, books, pens, or smartphones, as well as traffic signs, numbers […]

May 4, 2020 by Jean-Luc Aufranc (CNXSoft) - No Comments

Pi-oT ESP Module Leverages ESP32, Screw Terminals for IoT & Automation (Crowdfunding)

Last year, we covered Pi-oT Raspberry Pi add-on board designed for commercial and industrial IoT applications with five SPDT relays and eight analog outputs housed in a DIN rail enclosure, although some noted it may not be suitable for all industrial applications due to the lack of 24V DC input and protected outputs. But there seems to be a market anyway, as the company has now come up with a similar product, except that Pi-oT ESP module replaces the Raspberry Pi board with an ESP32 board, namely ESP32-DevKitC-D32. Pi-oT ESP module key features and specification: Board – ESP32-DevKitC-D32 based on ESP32-WROOM-D32 module with ESP32 dual-core processor, 32Mbit SPI flash Relays – 4x Panasonic SPDT relays controlled via GPIO pins Screws terminals for Relay outputs 6x analog inputs configurable as GPIO if needed 2x analog outputs configurable as GPIO if needed 2x GPIO 5V input, 3.3V, and GND Power Supply – […]

April 29, 2020April 29, 2020 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

Connect up to 32 Relays to Raspberry Pi with a Stackable 4-Relay Board (Crowdfunding)

People have been playing with off-the-shelf relays on Raspberry Pi boards ever since it was released in 2012, and over the years, some companies have maybe Raspberry Pi-specific relay boards such as Strawberry4Pi and Pi-OT. Two years ago, Sequent Microsystems introduced a stackable 8-Relay board enabling up to 64 relays to be connected to a single Raspberry Pi board. The 8-relay board only supported 24V/2.5A, and the company is now back on Kickstarter with a 4-relay board with 250V/10A line-switching relays that can offer up to 32 relays by stacking 8 boards connected to one Raspberry Pi board via the 40-pin I/O header. The board comes with four Songle 250V/10A relays, 3-pin pluggable connectors that accept 18 to 22 AWG wires, and a 5V/3A power supply is recommended. If you stack multiple relay board a beefier power supply may be required. Here are some power consumption numbers provided by the […]

April 16, 2020April 16, 2020 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

YARC Case Can House a Raspberry Pi Board with one HAT Expansion Board and Up to 3 Hard Drives (Crowdfunding)

There are plenty of enclosures for Raspberry Pi board and other compact x86 or Arm Linux SBCs, but many projects require expansion boards and it’s not always possible to use an off-the-shelf case. That’s with that in mind that Stefano Zorzi and other enthusiasts have created YARC (Yes, Another Raspberry Case), a hexagonal case that supports the most popular single board computers, even when an add-on board – such as a Raspberry Pi HAT – is attached to the board. There’s enough space for up to three 2.5″ hard drives. Those are the boards officially supported (tested?) with the case: Raspberry Pi B +, 2B, 3B, 3B +, 4B, A +, 3A + Hardkernel ODROID C1, C2 AAEON Up Board Asus Tinker board and Tinker board S Radxa Rock Pi 4 Orange Pi PC, Pi PC2, Pi PC Plus Basically any board with compatible mounting holes can be installed in […]

April 2, 2020April 2, 2020 by Jean-Luc Aufranc (CNXSoft) - No Comments

QuickDAQ.mikroBUS Development Board Leverages Visual Programming and MikroE Click Boards (Crowdfunding)

mikroBUS is a socket interface that allows you to connect MikroElektronik (MikroE) Click add-on boards that can be buttons, sensors, a servo controller, a wireless module, and practically anything you may think of since there are over 700 Click boards to choose from. We already covered several SBC with MikroBUS sockets starting with SolidRun HummingBoard Gate board that offered a single socket for 150+ Click boards at the time (2015). Other boards include Azure Sphere MT3620 with two MikroBUS sockets and MikroElektronika’s own Flip & Click board designed to take one Arduino shield and up to four Click boards. Another upcoming option is QuickDAQ.mikroBUS developer by EmbeddeTech in collaboration with MikroElektronika, powered by a Microchip PIC32 MCU, offering three MikroBUS sockets, and designed to work with “Virtuoso Low-Code Environment” that allows people to program the board using NodeRed-like visual programming and generate a Visual Studio project with code from the […]

March 10, 2020March 10, 2020 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

AirView Wireless Touchscreen Display Works with Phones, Laptops, Raspberry Pi, Etc. (Crowdfunding)

We’ve already written about several displays that take USB-C, HDMI or/and WiFi inputs to add a monitor to phones or computers including DUO add-on display and LAPSCREEN. AirView is another one of those and has launched on Kickstarter with a 13.3″ and 15.6″ Full HD versions featuring a touchscreen, built-in Miracast & AirPlay support, as well as HDMI and USB-C ports. It works with Android/iOS phones, traditional laptops & computers, SBC’s such as Raspberry Pi, and even game consoles. Two Airview models are available with the following hardware specifications: 15.6-inch model 1920×1080 resolution @ 60 Hz (4K model planned, but not available in KS) IPS display Multi-touch support Brightness – 250cd/m2 SRGB gamut – 98% Dimensions – 352 x 228 x 9.4 mm Weight – 1080 grams 13.3-inch model 1920×1080 resolution @ 60 Hz IPS display Multi-touch support Brightness – 300cd/m2 SRGB gamut – 100% Dimensions – 310 x 200 […]