IoT

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Broadcom unveils 2nd generation WiFi 7 chipsets: BCM6765, BCM47722, BCM4390

Broadcom unveils 2nd generation WiFi 7 chipsets: BCM6765, BCM47722, BCM4390

Broadcom WiFi 7 Gen2: BCM6765, BCM47722, BCM4390

Broadcom has announced its second generation WiFi 7 chipsets: the BCM6765 residential WiFi 7 access point chip, the BCM47722 enterprise WiFi 7 access point chip with dual IoT radios that support simultaneous operation for Bluetooth Low Energy (BLE), Zigbee, Thread, and Matter protocols, and the BCM4390 low-power Wi-Fi 7, Bluetooth, and 802.15.4 combo chip designed for use in mobile devices. This follows the introduction of Broadcom’s first WiFi 7 chipsets in April 2022 with residential and enterprise WiFi 7 access point chips, and a WiFi 7 client chip, but the second generation access point chipsets support 320 MHz 2-stream Wi-Fi operation and add extra features, and the BCM4390 optimized costs bringing WiFi 7 to lower-prices phones and devices. BCM6765 residential Wi-Fi access point chip highlights: CPU – Quad-core ARMv8 CPU with 10Gbps Ethernet PHY WiFi 7 Dual 2×2 tri-band (2.4, 5, and 6 GHz) capable radios that support simultaneous operation […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 10 Comments on Espressif ESP Thread Border Router board combines ESP32-H2 & ESP32-S3 wireless chips

Espressif ESP Thread Border Router board combines ESP32-H2 & ESP32-S3 wireless chips

ESP Thread Border Router Zigbee Gateway

Espressif Systems has launched the ESP Thread Border Router/Zigbee Gateway board based on ESP32-H2 (802.15.4) and ESP32-S3 (WiFi + BLE) modules following the contention of the Thread Interoperability Certificate V1.3 for the board and associated ESP Thread Boarder Router SDK built on top of the ESP-IDF framework and the open-source OpenThread protocol stack. The ESP Thread Border Router supports the protocol functions of the 1.3 Thread standard such as bidirectional IPv6 connectivity, Service Discovery Delegate, Service Registration Server, Multicast Forwarding, NAT64, and more, as well as product-level features such as a Web GUI for device configuration, automatic RCP (Radio Co-Processor) upgrade, RF coexistence, and so on. ESP Thread Border Router/Zigbee Gateway board specifications: Wireless modules ESP32-S3-WROOM-1 wireless module SoC –  ESP32-S3 dual-core Tensilica LX7 microcontroller @ 240 MHz with 2.4 GHz 802.11n WiFi 4 and Bluetooth 5.0 LE connectivity Memory – 2MB PSRAM Storage – 4MB SPI flash PCB antenna […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on $5 Ai-M62-12F-Kit RISC-V development board features BL616 WiFi 6, BLE 5.2, and Zigbee MCU, plenty of I/Os

$5 Ai-M62-12F-Kit RISC-V development board features BL616 WiFi 6, BLE 5.2, and Zigbee MCU, plenty of I/Os

Ai-M62-12F-Kit

Ai Thinker Ai-M62-12F-Kit is a development board based on Bouffalo Lab BL616 RISC-V microcontroller with 2.4 GHz WiFi 6, Bluetooth 5.2 LE, and an 802.15.4 radio (Zigbee/Thread), plus thirty I/O pin for expansion. We had already covered the tiny Sipeed M0S module based on BL616 MCU earlier this year along with its M0S dock board that exposed eight GPIO pins via a 12-pin header, and the “NodeMCU” Ai-M62-12F basically offers the same features but with many more I/Os thanks to two 15-pin headers, as well as an RGB LED and two user-programmable LEDs. Ai-M62-12F-Kit specifications: MCU – Bouffalo Lab BL616 32-bit RISC-V (RV32IMAFCP) microcontroller @ up to 320 MHz (384 MHz overclocked) with 480KB SRAM, 4MB flash, 2.4 GHz WiFi 6, Bluetooth 5.2 dual mode, and 802.15.4 radio (Zigbee) Antenna – PCB antenna USB – 1x USB Type-C port for power and programming I/Os – 2x 15-pin headers with Storage […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Nordic Semi nRF7001 is a 2.4GHz WiFi 6 companion IC for nRF52, nRF53, and nRF91 wireless chips

Nordic Semi nRF7001 is a 2.4GHz WiFi 6 companion IC for nRF52, nRF53, and nRF91 wireless chips

nRF7001 2.4GHz WiFi 6

Nordic Semi nRF7001 is the second nRF70 Series WiFi 6 companion IC. It is designed to add 2.4 GHz WiFi 6 connectivity to Nordic Semi nRF52 and nRF53 wireless SoCs and nRF91 cellular IoT system-in-package and support both client and access point mode. The nRF7001 follows the introduction of the nRF7002 dual-band (2.4GHz/5GHz) WiFi 6 companion IC last year, and target power or cost-optimized use cases where 5 GHz WiFi 6 may not be required or even suitable. Nordic Semi nRF7001 key features specifications: Complies with 802.11a/b/g/n/ac/ax 2.4 GHz band Wi-Fi 6 Station (STA) 1x Spatial Stream (SS) 20 MHz channel bandwidth 64 QAM (MCS7), 86 Mbps PHY throughput OFDMA (Downlink and Uplink) BSS coloring Co-existence interfaces, including Bluetooth LE Low-power and secure Wi-Fi for the IoT Target Wake Time (TWT) Security – WPA3 Host interface – SPI / QSPI Package – 6×6 mm QFN Since the nRF7001 is based […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on CompuLab UCM-iMX93 – A miniature NXP i.MX 93 module with WiFi 5 & Bluetooth 5.3

CompuLab UCM-iMX93 – A miniature NXP i.MX 93 module with WiFi 5 & Bluetooth 5.3

Compulab UCM-iMX93 system-on-module

CompuLab UCM-iMX93 is a miniature system-on-module powered by the new NXP i.MX93 Cortex-A55 AI processor family with up to 2GB RAM and 64GB eMMC flash. The tiny 38x28mm features a Gigabit Ethernet PHY, a WiFi 5 and Bluetooth 5.3 wireless modules, and plenty of multimedia, communication, and peripheral interfaces through two 100-pin high-density connectors including display and camera interfaces, USB ports, CAN FD, and up to 79 GPIOs. UCM-iMX93 specifications: SoC – NXP i.MX9352 or i.MX9331 dual-core/single-core Arm Cortex-A55 @ 1.5 GHz (industrial) / 1.7 GHz (commercial) with Arm Cortex-M33 real-time core @ 250 MHz, Arm Ethos U65 microNPU System Memory – 512MB to 2GB LPDDR4 Storage – 8GB to 64GB eMMC flash Networking Gigabit Ethernet PHY Certified WiFi 5 (802.11ac) and Bluetooth 5.3 BLE module (NXP 88W8997) 2x 100-pin 0.4mm pitch high-density UCM connectors Display 4-lane MIPI-DSI up to 1920 x 1080 @ 60Hz 4-lane LVDS up to 1366 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on reTerminal DM – A Raspberry Pi CM4-powered 10.1-inch HMI controller

reTerminal DM – A Raspberry Pi CM4-powered 10.1-inch HMI controller

reTerminal DM 10-inch Raspberry Pi CM4 HMI terminal

Seeed Studio’s reTerminal DM is an upgrade to the Raspberry Pi CM4-powered reTerminal with a larger 10.1-inch touchscreen display and a greater range of features and interfaces for various industrial applications. Described as a “Panel PC, HMI, PLC, IIoT Gateway all-in-one device”, the new reTerminal DM notably supports 12V-24V variable DC input and optionally PoE power input, its front panel is rated IP65 for protection against liquids and dust, a range of wired and wireless connectivity options are offered, and it also includes some serial and digital input and output interfaces. reTerminal DM specifications: SoM – Raspberry Pi Compute Module 4 with Broadcom BCM2711 quad-core Cortex-A72 processor @ 1.5 GHz, up to 8GB RAM, up to 32GB flash Storage – Optional M.2 NVMe SSD via M.2 2280 Key-M slot Display – 10.1-inch display with 1280 x 800 resolution, 10-point capacitive touchscreen 400-nit brightness, 170° H/V viewing angle Video Output – […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 7 Comments on NXP i.MX 91 single-core Cortex-A55 SoC to power Linux-based cost-optimized edge devices

NXP i.MX 91 single-core Cortex-A55 SoC to power Linux-based cost-optimized edge devices

NXP i.MX 91 CPU

NXP has just unveiled the NXP i.MX 91 single-core Cortex-A55 processor following the introduction of the i.MX 93 in 2021, and designed for cost-optimized edge devices running Linux. The NXP i.MX 93 processor comes with up to two Cortex-A55 cores, a Cortex-M33 real-time core, and an Ethos U65 microNPU, but targeting entry-level Linux systems, the NXP i.MX 91 processor does without the real-time core and the AI acceleration, while still integrating NXP EdgeLock Secure Enclave, and the company highlights support for multiple wireless connectivity options through companion chips such as the IW612 that supports Wi-Fi 6, Bluetooth 5.2, 802.15.4, and the new Matter protocol. NXP i.MX 91 specifications: CPU – Arm Cortex-A55 running at up to 1.4GHz with 256KB L2 cache System Memory – Up to 2.4GT/s x16 LPDDR4 with Inline ECC Storage 3x SD 3.0, SDIO 3.0, eMMC 5.1 1x Octal SPI including support for SPI NOR and SPI […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 6 Comments on Link.ONE LTE-M, NB-IoT, and LoRaWAN all-in-one LPWAN devkit is programmable with the Arduino IDE

Link.ONE LTE-M, NB-IoT, and LoRaWAN all-in-one LPWAN devkit is programmable with the Arduino IDE

RAKwireless Link.ONE

RAKwireless Link.ONE is an all-in-one LPWAN development kit programmable with the Arduino IDE and based on nRF52840 Cortex-M4F 2.4 GHz multi-protocol wireless microcontroller, Semtech SX1262 LoRa RF transceiver, and Quectel BG77 LTE-M and NB-IoT module and comprised of components from the company’s WisBlock IoT prototyping platform. Besides the WisBlock modules, the kit includes everything to get started with four antennas for LTE-IoT, LoRaWAN, GNSS, and Bluetooth connectivity, a USB cable for power and programming, and a Monogoto SIM card with global coverage and 500MB of data valid for 10 years. Link.ONE hardware specifications: RAK19007 WisBlock base board with USB connector and Li-ion charger RAK4631 WisBlock core module with Nordic Semiconductor nRF52840 32-bit Arm Cortex-M4F microcontroller @ 64 MHz with 1 MB Flash, 256 KB RAM, Bluetooth Low Energy 5.0 protocol stack Semtech SX1262 LoRa/LoRaWAN RF transceiver with LoRaWAN 1.0.2 protocol stack (supports Class A & C), global coverage support: RU864, […]

UP 7000 x86 SBC