IoT News - Page 43 of 182 - CNX Software

March 9, 2023March 9, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Microchip unveils Single Pair Ethernet (SPE) 10BASE-T1S and 100BASE-T1 Ethernet devices

Microchip has introduced a range of industrial-grade Single Pair Ethernet (SPE) devices for IIoT and industrial Operational Technology (OT) networks for low-speed Ethernet edge devices and a simplified cabling infrastructure for latency-sensitive applications. Microchip LAN8650/LAN8651 10BASE-T1S single pair Ethernet Controllers The LAN8650 and LAN8651 10BASE-T1S MAC-PHY Ethernet controllers come with an SPI for integration into basic microcontrollers rather than higher-end MCUs with a MAC. They can be used to connect sensors, actuators, and other devices over a simple twisted-pair cable. Microchip LAN8650/LAN8651 specifications: High-performance 10BASE‑T1S single-pair Ethernet PHY Compliant with IEEE Std. 802.3cg-2019 (10BASE-T1S) 10 Mbps over a single balanced pair of conductors Half-duplex point-to-point link segments up to at least 15m Half-duplex multidrop mixing segments up to at least 25m with up to at least 8 PHYs Integrated Media Access Controller (MAC) Host interface – SPI Supports time-sensitive networking (TSN) by timestamping frame ingress and egress EtherGREEN Energy Efficiency […]

March 6, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Elfin-EW11 is a compact WiFi to RS485 unit with Modbus TCP support

Elfin EW11/EW11A is a small WiFi to RS485 unit with Modbus TCP/IP support that works either in the 5 to 18V DC (EW11) or the 5 to 36V DC (EW11A) input range. The WiFi to RS485 adapter is offered with either an internal or external WiFi antenna, the RS485 interface is exposed through an RJ45 port, and an RJ45 to terminal block cable is usually included, as well as a DIN Rail mount. Elfin EW11/EW11A specifications: MCU (I’m not sure which one is used, and the specs depend on where you look..) Unnamed Arm Cortex-M3 microcontroller @ 96 MHz with 2MB flash, 128KB SRAM (on the product page) OR Unnamed microcontroller @ up to 160MHz with 2MB flash, 352KB SRAM (on Aliexpress) Networking Wireless – 2.4 GHz WiFi 4 with up to WPA2PSK security, station, AP, or station+AP modes; internal or external WiFi antenna depending on the model. Wired – […]

March 4, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

IoT board supports WiFi, Bluetooth, NB-IoT, Cat-M and GNSS with ESP32-S3 and SIM7080G modules

LILYGO T-SIM7080G-S3 is an ESP32-S3 WiFi and Bluetooth IoT board with a SIMcom SIM7080G LTE Cat-M (eMTC), NB-IoT, and GNSS module for low-power long-range connectivity and asset tracking. The board also comes with a 18650 battery holder, a solar panel input, a microSD card slot, a camera port, and several I/Os and provides an alternative to the TTGO T-Beam ESP32 board that relies on LoRaWAN for long-range connectivity instead. LILYGO T-SIM7080G-S3 specifications: Wireless modules Espressif ESP32-S3-WROOM-1-N16R8 module with ESP32-S3 dual-core LX7 microprocessor @ up to 240 MHz with Vector extension for machine learning, 16MB flash, 8MB PSRAM, WiFi 4 and Bluetooth 5 LE/Mesh SIMCom SIM7080G global multi-band Cat-M and NB-IoT module with GNSS Bands: Cat-M – B1/B2/B3/B4/B5/B8/B12/B13/B14/B18/B19/B20/B25/B26 /B27/B28/B66/B85 NB-IoT – B1/B2/B3/B4/B5/B8/B12/B13/B18/B19/B20/B25/B26/B28 /B66/B71/B85 Data rate Cat-M – Uplink: 1,119 Kbps, downlink: 589 Kbps NB-IoT: Uplink: 150 Kbps downlink: 136 Kbps LTE RF Power Class: 5 (Typ. 21dbm) GNSS – GPS, GLONASS, […]

March 3, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

SparkFun Thing Plus Matter – MGM240P board supports Matter, Zigbee, OpenThread, and Bluetooth Low Energy 5.3

SparkFun Thing Plus Matter – MGM240P board targets the development of applications using the Matter IoT protocol and features the MGM240P module based on Silicon Labs EFR32MG24 Arm Cortex-M33 wireless microcontroller with an 802.15.4 radio for Zigbee and OpenThread plus a Bluetooth Low Energy (BLE) 5.3 radio. The board also offers two rows of I/Os for upto 21 GPIOs and a Qwiic connector for expansion, another EFRM32 MCU acting as a J-link debugger, a microSD card, and can be powered via USB-C or a LiPo battery. SparkFun Thing Plus Matter – MGM240P specifications: MGM240P wireless module SoC – Silicon Labs EFR32MG24 microcontroller CPU – 32-bit Arm Cortex-M33 @ 39 MHz (MCU/module specs say up to 78 MHz, but maybe it’s clocked lower in this board for some reason, maybe lower power consumption?) Memory/Storage – 1536kB Flash Memory, 256kB RAM Wireless – 802.15.4 wireless protocols (Zigbee and OpenThread) and Bluetooth Low […]

March 1, 2023March 1, 2023 by Jean-Luc Aufranc (CNXSoft) - 21 Comments

LILYGO T-TWR is an ESP32-S3 board with an SA868 Walkie-Talkie module

LILYGO T-TWR is an ESP32-S3 development board fitted with an SA868 Walkie-Talkie module and a UHF or VHF antenna, a speaker, a microphone, a small 0.96-inch OLED, and a 18650 battery holder, plus some I/Os for expansion. Equipped with an ESP32-S3-WROOM-1-16NR8 module, the T-TWR offers WiFi 4 and Bluetooth 5.0 connectivity, a dual-core processor with 16MB flash and 8MB PSRAM, and enables users to design their own Walkie-Talkie, while its expansion capabilities allow the control of devices. LILYGO T-TWR specifications: Wireless module – Espressif ESP32-S3-WROOM-1-N16R8 module with ESP32-S3 dual-core LX7 microprocessor @ up to 240 MHz with Vector extension for machine learning, 16MB FLASH, 8MB PSRAM, WiFi 4 and Bluetooth 5 LE/Mesh Display – 0.96-inch OLED with 128×64 resolution based on SSD1306 I2C display driver SA868 Walkie-Talkie module based on RDA1846S chip Bandwidth: 12.5 kHz/25 kHz Sensitivity: -124 dBm Support 1.6W or 1.8W mode. The latter is not recommended due […]

February 27, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

8K AI embedded computer gets 4K HDMI input, WiFi 6, dual GbE interfaces, and more

Firefly EC-A3588Q 8K AI Embedded Computer

Firefly EC-A3588Q is a fanless 8K AI embedded computer powered by a Rockchip RK3588 processor and fitted with up to 32GB RAM, SATA or NVMe storage, offering dual Gigabit Ethernet, WiFi 6, Bluetooth 5.0, and optional 5G/4G cellular connectivity, dual 8K video outputs, etc… It is a higher-end and larger version of the Firefly EC-R3588SPC industrial mini PC based on the Rockchip RK3588S processor that adds a 4K HDMI input port, a VGA output port, gets two GbE interfaces and support for WiFi 6/Bt 5.0, offers more USB ports, and replaces some terminal blocks with DB9 interfaces for RS232, RS485, and CAN Bus interfaces. Firefly EC-Q3588Q specifications: SoC – Rockchip RK3588 octa-core processor with CPU – 4x Cortex-A76 cores @ up to 2.4 GHz, four Cortex-A55 cores @ up to 1.8 GHz GPU – Arm Mali-G610 MP4 quad-core GPU with OpenGL ES3.2 / OpenCL 2.2 / Vulkan1.1 support AI accelerator […]

February 20, 2023February 19, 2023 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Sparkfun NanoBeacon low power Bluetooth 5.3 beacon module supports Bosch BME280 and BMA400 sensors

Sparkfun NanoBeacon is a module equipped with InPlay IN100 NanoBeacon Bluetooth 5.3 beacon SoC, a Qwicc connector, and a few GPIOs designed to work with Bosch Sensortec BME280 3-in-1 humidity sensor, measuring humidity, air pressure, and ambient temperature, and the BMA400 ultra-low power accelerometer sensor. The IN100 NanoBeacon SoC consumes less than 650nA in sleep mode, supports proprietary, Bluetooth, Google Eddystone, and Apple iBeacon beacon modules, and offers a long range of up to several hundred meters. Sparkfun NanoBoard specifications: Bluetooth Beacon SoC – IN100 NanoBeacon SoC (See datasheet for details) Memory – 4 KB SRAM + 4 Kbit OTP memory Bluetooth 5.3 compliant Beacon Modes: Proprietary, BT, Google Eddystone, and Apple iBeacon compliant 2.4GHz RF frequency band, MedRadio band (2.36GHz) Programming-free and firmware-less design Long-range transmission: up to several hundred meters Security Authentication of beacon ID Privacy of advertising payload Power consumption Sub-uW power consumption for multi-year operation on […]

February 18, 2023February 18, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

IoT Prototype Kit is powered by an Alder Lake-H COM Express module with up to Core i5-12600HE CPU

IoT Prototype Kit Intel Alder Lake-P module

ADLINK has launched an IP-i IoT Prototype Kit based on their Express-ADP COM Express Type 6 Basic “Alder Lake-H” module with either an Intel Core i5-12600HE 12-core (4P+8E) processor clocked at up to 4.5 GHz or a Core i3-12300HE 8-core (4P+4E) processor reaching up to 4.3 GHz. The kit also includes the Express-BASE6 R3.1 carrier board, a thick heatsink with an active fan, a debug board (DB30 x86), and various cables for SATA storage, a DB9 COM port, and I/Os, and the kit can be used to develop applications for industrial automation and control, medical ultrasound, image processing and analysis, high-speed video encoding and streaming, predictive traffic analysis, multi camera-based AI, etc… The Express-ADP module supports up to 64GB DDR5 memory, optional on-module NVMe storage, up to 4x 4K displays, multiple PCIe Gen4 and Gen3 interfaces, SATA 3.0, and so on. You’ll find detailed Express-ADP COM Express module specifications in […]