IoT News - Page 40 of 190 - CNX Software

October 8, 2023October 7, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

M5Dial – An ESP32-S3 smart rotary knob with a touchscreen display

M5Stack M5Dial is a WiFi and Bluetooth-connected smart rotary knob with a round 1.28-inch touchscreen TFT display powered by an ESP32-S3 board, more precisely, the M5Stamp S3 IoT module. The user-programmable device comes with a rotary encoder recording the position and direction of the knob, an RFID module, an RTC, a buzzer, and under-screen buttons, as well as two Grove connectors for expansion enabling all sorts of projects. M5Dial specifications: Wireless MCU module – M5Stack M5Stamp S3 with SoC – Espressif Systems ESP32-S3FN8 dual-core 32-bit Xtensa LX7 microcontroller with AI vector instructions up to 240MHz, RISC-V ULP co-processor, 512KB SRAM, 2.4GHz WiFi 4 (802.11b/g/n), Bluetooth 5.0 BLE + Mesh, 8MB flash 2.4GHz 3D antenna USB – 1x USB Type-C port Expansion connectors for I/Os such as SPI, I2C, UART, ADC, and more Display – 1.28-inch TFT display with 240×240 resolution using GC9A01 driver, and FT3267 capacitive touchscreen controller RFID – […]

October 5, 2023October 5, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

UP Squared i12 Edge is a compact, yet feature-rich, fanless Alder Lake-P mini PC

UP Squared i12 Edge is a compact fanless mini PC powered by 12th Generation Intel Alder Lake-P processors from the Celeron 7305E penta-core CPU up to an Intel Core i7-1270PE 12-core processor, but still a good range of ports and features. Based on the UP Squared i12 SBC introduced earlier this year, the UP Squared i12 edge mini PC comes with up to 16GB LPDDR5 RAM and features a 64GB or 128GB SSD soldered on board, plus an M.2 2280 NVMe socket and a SATA port for additional storage. The system also has two gigabit Ethernet ports, optional WiFi and Bluetooth, three 4K-capable display interfaces (HDMI, DisplayPort, USB-C), and three USB 3.2 Gen 2 ports. UP Squared i12 Edge specifications: 12th generation Alder Lake-P SoC: Intel Core i7-1270PE 12-core/16-thread processor @ up to 3.30GHz (E-cores) / 4.50GHz )P-cores) with 96EU Intel Xe graphics – PBP: 28W, up to 64W MTP […]

September 24, 2023December 11, 2024 by Jean-Luc Aufranc (CNXSoft) - No Comments

EDATEC ED-IPC2100 industrial computer offers 4x RS485/RS232 ports

EDATEC ED-IPC2100 industrial computer with RS485 and RS232 ports

EDATEC has launched four more Raspberry Pi CM4-powered industrial computers with the ED-IPC2100 Series that mostly differ from the earlier ED-IPC2010 model with an extra M.2 Key-B socket for an SSD, an extra 10/100Mbps Ethernet port, and four COM ports with RS232 or RS485 interfaces depending on the exact model. The new ED-IPC2100 series industrial computer family ships with a Raspberry Pi Compute Module 4 with up to 8GB RAM, 32GB flash, optional WiFi 5 and Bluetooth 5.0, and offers a full-size HDMI video output, two Ethernet ports, and a few USB ports. The ED-IPC2120 model looks to offer some extra features such as an HDMI Touch FPC connector, MIPI CSI camera and DSI display connectors, and audio interfaces. ED-IPC2100-series specifications: SoM – Raspberry Pi CM4 SoC – Broadcom BCM2711 quad-core Cortex-A72 processor @ 1.5GHz with VideoCore VI GPU System Memory – 1GB, 2GB, 4GB, or 8GB LPDRR4-3200 RAM Storage […]

September 18, 2023September 17, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Realtek RTL8852BE based WiFi 6 and Bluetooth 5.2 module targets Smart Home, industrial and healthcare applications

Realtek RTL8852BE WiFi 6 LGA & M2 modules

Telit Cinterion WE310K6-P is a dual-band Wi-Fi 6 and Bluetooth 5.2 based on the Realtek RTL8852BE wireless controller and designed to be integrated into connected devices for Smart Home, medical, industrial, and smart city applications. The WE310K6-P wireless is available in either LGA or M.2 module form factors and can operate in the -40°C to +85°C temperature range which should make it suitable for a wide range of Linux devices. Telit Cinterion WE310K6-P specifications: Wireless chipset – Realtek RTL8852BE Wi-Fi WiFi 6 802.11 a/b/g/n/ac/ax (2.4GHz, 5GHz) with 20MHz, 40MHz, or 80MHz bandwidth Dual-stream spatial multiplexing up to 1201 Mbps data rate Tx output – 19 dBm @ 2.4 GHz, 18 dBm @ 5 GHz Wi-Fi 802.11 e, h, k, i support Security features such as WPA3 and integrated crypto hardware Bluetooth Version 5.2 Dual mode with Bluetooth 2.1 Classic Bluetooth Low Energy up to 2 Mbps Bluetooth LE Audio (CIS) […]

September 16, 2023February 9, 2025 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Sparkfun launches cheaper no-code “DataLogger IoT” board compatible with Qwiic modules

Last May, SparkFun introduced the “Datalogger IoT – 9DoF” no-code platform with support for over 50 Qwiic sensor modules and a built-in 9-axis IMU sensor and magnetometer. Taking into consideration that some users may not make use of the built-in sensors, the company decided to launch a cheaper version called the “DataLogger IoT” that can still get data from Qwiic sensor and GPS modules without any programming thanks to the “no-code” Arduino firmware preloaded on the ESP32-WROOM-32E module. SparkFun DataLogger IoT specifications: Wireless module – ESP32-WROOM-32E with: ESP32 dual-core microcontroller 4MB flash 2.4 GHz WiFi and Bluetooth LE connectivity, built-in PCB antenna Storage – MicroSD card slot USB – 1x USB Type-C port for power and configuration via CH340C Expansion – 2x Qwicc I2C connectors for sensors and/or GPS module Misc Boot and Reset buttons Status and charging LED, WS2812 RGB LED Jumpers to enable/disable LEDs, I2C pull-up resistors, and […]

September 15, 2023September 18, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Cadence Neo NPU IP scales from 8 GOPS to 80 TOPS

Cadence Neo NPU (Neural Processing Unit) IP delivers 8 GOPS to 80 TOPS in single core configuration and can be scaled to multicore configuration for hundreds of TOPS. The company says the Neo NPUs deliver high AI performance and energy efficiency for optimal PPA (Power, Performance, Area) and cost points for next-generation AI SoCs for intelligent sensors, IoT, audio/vision, hearables/wearables, mobile vision/voice AI, AR/VR and ADAS. Some highlights of the new Neo NPU IP include: Scalability – Single-core solution is scalable from 8 GOPS to 80 TOPS, with further extension to hundreds of TOPS with multicore Supports 256 to 32K MACs per cycle to allow SoC architects to meet power, performance, and area (PPA) tradeoffs Works with DSPs, general-purpose microcontrollers, and application processors Support for Int4, Int8, Int16, and FP16 data types for CNN, RNN and transformer-based networks. Up to 20x higher performance than the first-generation Cadence AI IP, with […]

September 14, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Rockchip RK3588 AIoT gateway supports WiFi 6, 5G, RS232, RS485, LoRaWAN, BLE, and Ethernet

Dusun DSGW-380, also called Dusun Pi 5, is an industrial AIoT gateway powered by the Rockchip RK3588 octa-core processor with a 6 TOPS AI accelerator and supporting a wide range of connectivity options. The gateway comes with 8GB LPDDR4 memory, and up to 128GB eMMC flash, and operates in a wide -25 to +75°C temperature range. It supports dual gigabit Ethernet, RS232, and R485 wired connectivity and various wireless protocols including WiFi 6, Bluetooth LE, 5G, and LoRaWAN. Dusun DSGW-380 specifications: SoC – Rockchip RK3588 octa-core processor with CPU – 4x Cortex‑A76 cores @ up to 2.4 GHz, 4x Cortex‑A55 core @ 1.8 GHz GPU – Arm Mali-G610 MP4 “Odin” GPU @ 1.0 GHz Video decoder – 8Kp60 H.265, VP9, AVS2, 8Kp30 H.264 AVC/MVC, 4Kp60 AV1, 1080p60 MPEG-2/-1, VC-1, VP8 Video encoder – 8Kp30 H.265/H.264 video encoder AI accelerator – 6 TOPS NPU System Memory – 8GB RAM Storage – […]

September 6, 2023September 6, 2023 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Using SenseCAP T1000 LoRaWAN GPS Tracker for cattle tracking

SenseCAP T1000 Review Smart Agriculture Cattle Tracking

SenseCAP T1000 is a credit-size GPS tracker using LoRaWAN low-power long-range connectivity. Smart Agriculture is one specific application that can leverage IoT and LoRaWAN to analyze and manage soil, crops, and water, but also to track the location of livestock. This is an important aspect of farming, and we’ll use the SenseCAP T1000 LoRaWAN GPS tracker to track cattle in this article/review. SenseCAP T1000 unboxing The package contains the SenseCAP T1000 GPS Tracker device, which is about the size of a credit card, and a charging cable. Smart cattle tracking with SenseCAP T1000 LoRaWAN tracker Here are some of the benefits and features of Smart cattle tracking: Identify the location of the swarm in real-time Identify animals easily Increase efficiency and reduce human labor Secure your farm by using the tracker as an anti-theft device Weather change alerts Virtual fence to generate an alert when the animal leaves the designated […]