indiegogo News - Page 16 of 21 - CNX Software

November 20, 2014November 23, 2014 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

$249 Jolla Tablet Runs Sailfish OS 2.0 on a Quad Core Intel Processor (Crowdfunding)

After launching the Jolla phone last year, Jolla has now unveiled the Jolla Tablet running the company’s Sailfish OS, and just like Nokia N1, powered by a quad core Intel processor. Instead of directly using a pre-order system like with the Jolla smartphone, they’ve decided to launch an Indiegogo campaign, and price the tablet much more aggressively than the phone, as perks started at just $189 for early backers. Jolla tablet specifications: SoC – Unnamed Intel 64-bit quad core processor @ 1.8 GHz, which should be Z3740(D), Z3745(D) or Z3560 processor. System Memory – 2GB DDR3L-RS Storage – 32GB eMMC + micro SD slot up to 32GB Display – 7.85″ IPS display, 2048 x 1536 resolution, 5-point capacitive touch Camera – 5.0MP rear camera, 2.0MP front-facing camera Audio – 3.5mm audio jack + speaker(s)? Connectivity – Dual band 802.11 a/b/g/n Wi-Fi, GPS Sensors – Accelerometer, light sensor, and proximity sensor. […]

November 19, 2014November 19, 2014 by Jean-Luc Aufranc (CNXSoft) - 22 Comments

DWA8 ESP8266 Wi-Fi Module Features a 10-bit ADC, Up to 8 GPIOs, 4 PWM Outputs, and More (Crowdfunding)

Espressif ESP8266 based ESP-01 module may now cost $3, but it’s limited to only two GPIOs, so a Dooao, a Chinese company based in Beijing, has decided to make a new ESP8266 module with more GPIOs, PWM signals, SPI, UART. and a 10-bit ADC. Dooao DWA8 module specifications: SoC – Espressif Systems ESP8266 32-bit RISC processor @ 80 MHz with 120KB RAM (40KB usable), built-in 802.11 b/g/n support. Wi-Fi – 802.112 b/g/n, STA/AP/STA+AP modes, WEP/WPA-PSK/WPA2-PSK security Interfaces: Up to 8x GPIOs Up to 4x PWM SPI (master & slave) up to 40MHz UART with hardware FC up to 4Mbps 1x channel 10bit ADC Power supply – Single 3.3V (2.8 to 3.6V) Power consumption – Max: 70 mA @ 3.3V (230 mW); typical: 12mA; standby < 200 uA; “soft power off” < 10uA. Dimensions – 27.13 x 17 x 2.3 mm (a bit larger than ESP-01) Temperature Range – Operating: -40 […]

November 6, 2014November 6, 2014 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Robotics News – Hack-E-Bot and RiQ Educational Robots, and Maker Club 3D Printed Robots (Pre-Orders / Crowfunding)

I’ve come across several robotic projects this week, so instead of picking one up, or writing a post for each, I’ll summarize the three products into one post. Two of the projects are educational robots based on Arduino, with the sub $50 Hack-E-Bot, or the more advanced RiQ robot, and Maker Club is a company providing the electronics for robotics kit, and you print the plastic parts with your 3D printer. Hack-E-Bot Robot Hack-E-Bot is an affordable open source robot that hopes to encourage children to learn about engineering, electronics, and programming. The robot is powered by Adafruit’s Trinklet Arduino compatible board, connected to a breadboard, and some add-on boards sensors. The basic version comes with a Sonar sensor, but more add-on boards are on the way including bump sensors, a buzzer, colored lights, a claw, a servo scanner, and so on. The project is listed on CrowdSupply, and has […]

October 29, 2014 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Zero+ IoT Wi-Fi Board is Programmable with Lisp (Crowdfunding)

There have been so many low cost Wi-Fi modules and boards with GPIO headers announced this year, especially on crowdfunding sites, and from the hardware point of view, Zero+ (Zero Plus) board looks very much like many other Ralink RT5350 boards such as Vocore or AsiaRF AWM002, but what makes it different is that it can be programmed with Lisp from a web-based IDE. But let’s go through Zero+ board specifications first: SoC – Ralink/Mediatek RT5350 MIPS processor @ 360MHz with dual band 802.11n Wi-Fi with data Rate up to 150Mbps System Memory – 32 MB RAM Storage – 8MB to 16 MB SPI Flash (for firmware) Expansions Headers – 2x headers with access to I2C, SPI, USB, 2x UART, JTAG, and 14x GPIOs USB – 1x USB host port, 1x micro USB for power Misc – 2x buttons Dimensions – 36 x 25mm (possibly module dimensions only, not full board). I’m […]

September 16, 2014 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

WeIO is an Open Source Hardware IoT Board Programmable from a Web Browser (Crowdfunding)

WeIO is an open source hardware board for the Internet of things with Wi-Fi connectivity and lots of I/Os designed by nodesign, a French based startup, in collaboration of 8devices, the makers of the Carambola boards. WeIO is powered by an Atheros AR9331 SoC running OpenWRT as well as an NXP LPC MCU for faster handling of I/Os and support for analog I/Os. One interesting aspect of this board is that it can be programmed via a web browser using HTML5 or Python, and it does not rely on the Cloud to store data. WeIO hardware specifications: SoC – Atheros AR9331 MIPS 24K Wireless SoC @ 400 MHz MCU – NXP LPC11xx ARM Cortex M0 MCU for analog I/O and real-time H/W interfaces System Memory – 64 MB DDR2 Storage – 16 MB flash + micro SD slot Connectivity – 802.11 b/g/n Wi-Fi with on-board antenna (AP and STA modes), […]

September 15, 2014September 15, 2014 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

$125 Com 1 Android Wear Watch Powered by Ingenic JZ4775 MIPS Processor (Crowdfunding)

If you’d like to get an Android Wear watch, but are not quite ready to spend $200+ for the models currently available, the Com 1 Android Wear smartwatch could be interesting as you may get one for as low as $125, albeit with higher risks since it’s part of a flexible funding Indiegogo campaign. The watch is powered by Ingenic JZ4775 MIPS processor, features a 1.6″ AMOLED display, and is IP67 rated (Water- and dust-proof). Com 1 watch hardware specifications: SoC – Ingenic JZ4775 XBurst (MIPS) processor @ 1.0 GHz with 2D graphics, and VPU (MPEG-2, MPEG-4, VC-1, H.264, VP8, RV9), 720p@30fps System Memory – 375 MB LPDDR1 Storage – 4 GB eMMC Display – 1.6” AMOLED touchscreen display, 320 x 320 resolution, 16.7 Million Colors , LED back light, Brightness: 300 cd/m^2. Connectivity – WiFi (802.11 a/b/g/n at 2.4/5 GHz), Bluetooth 4.0 + EDR (BLE Compliant), FM, and NFC Sensors – […]

September 1, 2014May 3, 2024 by Jean-Luc Aufranc (CNXSoft) - 15 Comments

xWifi Open Source Hardware Wi-Fi Module and Dock for the Internet of Things (Crowdfunding)

For some reasons, Wi-Fi modules are pretty popular this year. After modules such as VoCore, AsiaRF AWM002, and ESP8266, here’s come xWifi. This module is based on Mediatek MT7681 SoC which includes a TCP/IP stack like Espressif ESP8622 or TI CC3300, so it won’t run OpenWRT like VoCore or AsiaRF modules. The module only consumes about 350mW during transfer, it will be open source hardware, and the xWifi module plus a dock with a 10A relay, a humidity and temperature sensor, and a LED will go for as low as $17. xWifi module only specifications: SoC – Mediatek MT7681 802.11 b/g/n SoC with 32-bit RISC CPU. Support for Client/softAP mode. Package size 5×5 mm Storage – 512KB SPI Flash (for firmware) I/Os via headers: UART and SPI interfaces. 5x GPIOs PWM Power – 3.3V, GND Power Consumption – ~70mA @ 5V (during RX active) Dimensions – 14 x 17 mm The […]

August 20, 2014August 22, 2014 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Raspberry Pi Based Slice, and EzeeCube Quad Media Players Support Internal Hard Drives (Crowdfunding)

Slice is a media player based on Raspberry Pi Compute Module, and EzeeCube Quad is media hub powered by Freescale i.MX6 Quad, and an upgrade to EzeeCube based on i.MX6 dual, which was successfully funded. The underlying hardware between Slice and EzeeCube is much different, but both devices have a lot in common. They are both media players currently being crowd-funded respectively in Kickstarter and Indiegogo, both comes with an internal hard drive, run XBMC, targets typical end-users (rather than tinkerers) and are somewhat pricey. Slice Media Player When I first saw Slice, all I could see was an Raspberry Pi module, put in a case with an internal hard drive bay, and lots of pretty RGB LEDs, and with an air mouse sold for an inflated price of 114 GBP ($190 US) without hard drive or 179 GBP ($300 US) with a 1TB drive, with admittedly some cheaper early […]