gateway News - Page 27 of 35 - CNX Software

September 12, 2019February 16, 2020 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Habanero Qualcomm IPQ4019/IPQ4029 SoM Brings 802.11ac Wave2 WiFi to Linux Gateways and Routers

Last April, we first wrote about Qualcomm IPQ4019 quad-core Cortex-A7 processor with built-in 802.11ac Wave 2 WiFi, as it was found in Qualcomm Mesh Networking DevKit with support for Amazon Alexa. A few months later, we discovered router boards powered by either IPQ4019 or IPQ4029 processor such as Dakota DR40X9 or MikroTik RB450Gx4. The latter does not come with WiFi at all and instead leverages the hardware IPSec encryption built-into the processor. Habanero System-on-Module Today, we’ve come across the first IPQ4019 / IPQ4029 system-on-module we’ve countered so far, courtesy of 8devices with their Habanero and Habanero-I 802.11ac Wave 2 modules based on the respective processors. Habanero(-I) specifications: SoC – Qualcomm IPQ4019/IPQ4029 quad-core Arm Cortex-A7 processor @ 717 MHz with NEON, FPU, hardware-based NAT engine, and crypto accelerator System Memory – 512 MB DDR3L RAM Storage – 32MB NOR flash; up to 1 GB NAND flash on baseboard Connectivity QCA8075C 5-port […]

July 23, 2019January 9, 2020 by Ayo Ayibiowu - 6 Comments

N-Fuse Launches Raspberry Pi 3B+ LoRaWAN Gateway with PoE Support

PoE enabled Raspberry Pi 3B+ based LoRaWAN™ Gateway

Raspberry Pi is everywhere, and this small size single-board computer has reshaped technology and STEM education. The launch of the recent Raspberry Pi 4 is evident in the success and continuous growth. The Raspberry Pi 3B+ has seen so much success in several maker’s projects, while not the most powerful SBC in the market, but undoubtedly one of the most popular. I once put together an AI-powered mobile robot using just a Raspberry Pi 3B+, an RPLidar A2, and Raspberry Camera which was way capable of so many things. Another exciting Raspberry Pi end product is the “PoE enabled Raspberry Pi 3B+ based LoRaWAN Gateway” from n-fuse. The PoE enabled Raspberry Pi 3B+ based LoRaWAN Gateway as called by n-fuse is a LoRaWAN gateway based on the Raspberry Pi 3B+, the LRWCCx-MPCIE Concentrator, and the SBCPoE RPI Hat. It supports both the Europe 868Mhz and America 915Mhz frequency (you have […]

July 19, 2019July 19, 2019 by Ayo Ayibiowu - 2 Comments

MikroTik is Launching a new set of LoRa products this summer

MikroTik, the Latvian network equipment manufacturer, is reportedly launching a new set of IoT LoRa devices this summer. MikroTik who has been traditionally known for its wireless technologies, especially products related to wireless networking like routers, switches, antennas, and others, is going full fledged in support of LoRa network, the promising LPWAN technology for IoT applications. MikroTik announced a new LoRa based Gateway product in Vienna back in March 2019 during the MUM Europe MikroTik User Meetings. It was a combination of a wAP 2GHz outdoor AP with a LoRaWAN card inbuilt inside and will work just like every other LoRa gateways out there. The gateway is expected to support both public and private network server. According to MikroTik, they promised to cut down the high-end prices of LoRa gateway: We will undercut that price be a very very big difference, so our LoRa gateway will much much more affordable than […]

July 3, 2019July 3, 2019 by Tiwalade Joanna Okedara - 2 Comments

M2M-IoT GW-01 LoRaWAN Gateway is equipped with Orange Pi Zero H2+ SBC

M2M-IoT has developed a new LoRa gateway. The gateway, GW-01, is based on Orange Pi Zero H2+ board. While it is new, it has a lot of useful features. The new GW-01 gateway operates in the 868MHz or 915MHz LoRa frequencies and has -139 dBm sensitivity. Furthermore, the GW-01 is fully functional. It is also an open source low-cost solution to developing a LoRaWAN network. In addition, the gateway supports both OpenWrt, and Armbian distributions, and you’ll find documentation for both on Github. Another great thing about the gateway is that it has two boards. Also, the first board, which is on top, is based on SX1301. This 8 channel LoRa concentrator implements the LoRa physical interface. Now, the second board is at the bottom. It is also the model that the whole gateway was based on. This board is the OrangePi Zero H2+ 256MB (RAM) development board. The gateway […]

May 14, 2019February 16, 2020 by Jean-Luc Aufranc (CNXSoft) - No Comments

BB-400 Neuron Edge Dual Ethernet Industrial Controller Combines Raspberry Pi CM3+ and Arduino MCU

bb-400 neuron edge industrial controller

While the Raspberry Pi boards are mostly promoted as tools to teach STEM to kids and adults alike, they have found their way in a fair amount of industrial products, including ModBerry M500 industrial computer, Janz Tec emPC-A/RPI3 industrial embedded controller, and Kunbus RevolutionPi RevPi Core among others. There’s yet another option with Brainboxes BB-400 Neuron Edge industrial controller that was announced last year with Raspberry Pi Compute Module 3, but recently got an upgrade to Raspberry Pi Compute Module 3+. The controller features two Ethernet ports and also includes an Arduino compatible microcontroller to control the system’s eight configurable digital inputs and outputs. BB-400 Neuron Edge industrial controller specifications: SoM – Raspberry Pi Compute Module 3+ with Broadcom BCM2837B0 quad-core , Cortex-A53 processor @ 1.2GHz, 1 GB LPDDR2, 32GB eMMC Flash storage MCU – Unnamed Microchip Atmel Arduino compatible microcontroller Connectivity Ethernet Uplink Port – 1x RJ45 jack, 10/100Mbps […]

May 2, 2019 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Semtech Releases Open Source Software for LoRa Gateways & Devices

Semtech has released open source software for LoRa-based gateways including LoRa Basic Station packet forwarder for Linux-based gateways, LoRa Basic MAC implementation of the LoRa Alliance’s LoRaWAN specification, and LoRa Basic loader bootloader capable of handling firmware updates. All three components are available for free under a revised 3-Clause BSD license. LoRa Basic Station supports LoRaWAN Classes A, B, and C, presents a unified radio abstraction layer supporting Concentrator Reference Designs v1.5 and v2, and implements various backend protocols. Apart from mbedTLS and libloragw/-v2, it does not rely on external dependencies, the code is written in C language only, and easily portable to Linux gateways and embedded systems. LoRa Basic MAC is a fork of IBM’s LMiC library, also implemented in C language, supports multiple regions selectable at compile and/or run time, and can handle Class A, Class B, and Class C devices. Basic MAC uses LoRa Basic loader to […]

March 20, 2019 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

RAK Wireless Launches RAK7258 Indoor LoRa Gateway for $149

RAK Wireless has just launched a new indoor LoRa gateway with their RAK7258 model featuring Semtech SX1301 8-channel digital baseband chip. The OpenWrt gateway supports Ethernet with PoE, 2.4GHz WiFi, optional NB-IoT, LTE Cat M, LTE 4G module, and is fully compatible with LoRaWAN 1.0.2. The gateway supports all main LoRa regions including EU433, CN470, EU868, US915, and AS923. RAK7258 gateway specifications: SoC – MediaTek MT7628 MIPS 24KEc processor @ 580 MHz System Memory – 128MB DDR2 RAM Storage – eMMC flash, microSD card slot Connectivity 10/100 Ethernet with PoE 802.11 b/g/n WiFi 4 with internal antenna LoRa via RAK833 mini PCIe card + RP-SMA antenna Cellular – Extended NB-IoT, Cat M, LTE 4G, supported by default; nano SIM card slot USB – 1x USB 2.0 host port Console – RJ45 RS-232 port Misc – 6x status LED Power Supply – 12V/2A (default) or 42-57V DC PoE Dimensions – 180 […]

March 4, 2019March 4, 2019 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Pycom Pygate is a 50 Euros 8-channel LoRa Gateway Board

Semtech SX1308 digital baseband Chip for indoor LoRaWAN pico gateways was announced a few years ago, but it took a while before multi-channel gateways integrated the new low cost chip, and 2019 appears to be the year where pico LoRa gateway will be launched. We covered the $69 The Things Indoor Gateway a few weeks ago, but there will be soon another option, although geared towards developers, with Pycom Pygate low-cost 8-channel gateway board that connects to LoRa or the company’s Pymesh network. Pycom Pygate gateway board preliminary features and specifications: Dual SX1257 transceivers for a total of 8 channels support Frequencies – 863-870 MHz and 902-928 MHz Baseband processor: Semtech SX1308 Ultra-low power standby mode Ethernet with PoE via the optional daughter board Powered via USB, LiPo Battery and Ethernet via the optional daughter board LiPo battery charging via the USB port USB to serial connection for the Pycom […]