gateway News - Page 17 of 35 - CNX Software

October 27, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

CompuLab IOT-GATE-RPI4 gateway targets industrial control and monitoring

Compulab IOT-GATE-RPI4 CM4 industrial gateway

Compulab IOT-GATE-RPI4 is another industrial gateway based on the Raspberry Pi CM4 module that offers a different feature set and form factor compared to solutions like TECHBASE iModGATE-AI gateway or QWave Systems CatsPi Industrial carrier board. Designed with industrial control and monitoring in mind, the IOT-GATE-RPI4 gateway offers multiple RS485, RS232 and CAN FD ports, Ethernet, 4G LTE/4G, WiFi 802.11ac, and Bluetooth 5.0 connectivity, as well as a wide -40°C to 80°C operating temperature range, plus a wide input voltage from 8V to 36V as well as PoE support. Compulab IOT-GATE-RPI4 specifications: SoM – Raspberry Pi Compute Module 4 (CM4) with SoC – Broadcom BCM2711 quad-core ARM Cortex-A72 @ 1.5GHz plus VideoCore IV GPU with H.265 (4Kp60 decode), H.264 (1080p60 decode, 1080p30 encode) System Memory – 1GB to 8GB LPDDR4 Storage – 16GB to 128GB eMMC flash soldered on-board Secondary Storage – 64GB – 256GB NVMe flash via optional module […]

October 6, 2021December 18, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

MediaTek unveils Filogic 830 & Filogic 630 WiFi 6/6E chips

MediaTek has recently introduced the Filogic connectivity family with two parts, namely the Filogic 830 Wi-Fi 6/6E system-on-chip (SoC), and the Filogic 630 Wi-Fi 6E network interface card (NIC) solutions. The WiFi 6/6E tri-band (2.4, 5, and 6 GHz) chips are Wi-Fi Alliance EasyMesh certified, and designed for home, business, and enterprise router and repeater devices, home automation bridges, IoT gateways, as well as consumer devices such as laptops, TVs, IP cameras, etc… The MediaTek Filogic 830 is a complete 12nm SoC with a quad-core Cortex-A53 processor clocked at up to 2 GHz per core delivering over 18,000 DMIPs, hardware acceleration engines for Wi-Fi offloading and networking, dual 4×4 Wi-Fi 6/6E for up to 6Gbps connectivity, two 2.5Gbps Ethernet interfaces, and various other peripheral interfaces, but MediaTek did not provide any details about those. The company also says the chip includes FastPath low latency technology for gaming and AR/VR applications. […]

September 27, 2021November 15, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

ZB-GW03 ESP32-based Ethernet Zigbee gateway works with Tasmota firmware

ZB-GW03 is an Ethernet Zigbee Gateway compatible with eWelink mobile app and with a design similar to SONOFF ZBBridge gateway but replacing ESP8266 SoC by ESP32 SoC, and adding an Ethernet port. The ZB-GW03 gateway is apparently based on the same Silicon Labs EFR32MG21 Zigbee Arm Cortex-M33 chip and has been hacked to run Tasmota open-source software for people preferring more flexibility and/or integration with OpenHAB or Home Assistant open-source home automation frameworks via Zigbee2MQTT. ZB-GW03 gateway specifications: Main MCU – Espressif Systems ESP32 dual-core Tensilica TX6 processor @ 240 MHz with WiFi 4 and Bluetooth connectivity Zigbee MCU – Silicon Labs EFR32MG21 Arm Cortex-M33 MCU @ 80 MHz with Zigbee 3.0 connectivity Connectivity 10/100M Ethernet, WiFi, and Bluetooth via ESP32 Zigbee 3.0 via Silabs MG21 MCU with support for 128 nodes, up to 200+ meter range One 2.4 GHz Zigbee antenna One 2.4 GHz PCB antenna for WiFi Misc […]

September 27, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Geniatech GTW410 – An ultra compact IoT gateway based on Snapdragon 410E SoC

After writing about Azulle Ally Snapdragon 450 mini PC, I was reminded there are other small form factor Snapdragon devices such as Geniatech GTW410 based on the earlier Snapdragon 410E quad-core processor. While the GTW410 is marketed as an “Embedded IoT Gateway”, it could also serve as an entry-level industrial mini PC with up to 2GB RAM, 16GB eMMC flash, as well as HDMI, Ethernet, and USB ports. Geniatech GTW410 specifications: SoC – Qualcomm Snapdragon 410E (APQ8016) quad-core ARM Cortex A53 processor @ 1.2 GHz with Adreno 306 GPU System Memory – 1 or 2 GB LPDDR3 @ 533MHz Storage – 8 or 16 GB eMMC 5.0 flash + micro SD 3.0 (UHS-I) slot Video Output – HDMI 1.3 up to 1080p @ 30 Hz Connectivity – 10/100M Ethernet, Integrated 802.11 b/g/n, Bluetooth 4.1, GPS with on-board antenna, optional Zigbee USB – 2x USB 2.0 host ports, 1x micro USB […]

September 24, 2021April 26, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

SolidSense N8 IoT Compact gateway supports Wirepas Massive

SolidRun “SolidSense N8 IoT Compact” is a Linux Edge gateway based on NXP i.MX 8M Nano Solo processor that offers Gigabit Ethernet, WiFi 5, Bluetooth 5.0, and optional 4G LTE Cat 4 & GPS connectivity, plus Wirepas Massive (previously Wirepas Mesh networking) via a module based on Nordic Semi nRF52832 wireless Cortex-M4 microcontroller. The gateway comes with 1GB RAM, 8GB storage, offers optional RS485 and CAN interfaces, and targets IoT applications such as smart metering, automation, asset tracking, safety & security, and smart buildings. SolidSense N8 IoT Compact gateway SolidSense N8 IoT Compact specifications: SoC – NXP i.MX8M Nano single core Arm Cortex A53 @ 1500MHz + Cortex M7 @ 650MHz System Memory – 1GB DDR3 Storage – 8GB eMMC flash, MIcroSD card slot Connectivity Gigabit Ethernet RJ45 port with optional PoE support 802.11 a/b/g/n/ac WiFi 5 and Bluetooth 5.0 Optional 4G LTE Cat 4 (Global) + GPS with fallback […]

August 17, 2021September 20, 2022 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

ZiGate-Ethernet – An ESP32 Ethernet, WiFi, and BLE Gateway with optional Zigbee connectivity

ZiGate Ethernet Raspberry Pi 4 enclosure

Frédéric Dubois, aka fairecasoimeme, has recently released ZiGate-Ethernet, an home automation gateway based on Espressif Systems ESP32 wireless SoC with Ethernet, WiFi, and Bluetooth LE connectivity. The gateway can also take an optional PiZiGate+ Zigbee module for support for a wider range of home automation gizmos, and everything is designed to fit in the official Raspberry Pi 4 enclosure. ZiGate-Ethernet specifications: Wireless module – ESP32-WROOM-32E with ESP32 dual-core processor, 16MB flash, PCB antenna Connectivity 10/100M Ethernet RJ45 port implemented through LAN8720 as on several other ESP32 Ethernet boards 2.4GHz WiFI 4 Bluetooth LE 4.2/5.x Zigbee through PiZiGate+ module with PCB antenna or optional external antenna USB – Micro USB port for power and programming Expansion – 16-pin GPIO header with up to 10x GPIO, 7x ADC, UART, 5V, 3.3V, and GND Misc- Reset and Flash button, ESP32/FTDI UART selection switch, Power Supply – 5V/500mA via micro USB port Dimensions – […]

August 16, 2021April 8, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

5G compatible Arm Pico-ITX SBC is expandable through multi-function I/O board

IBASE IBR215 SBC plus IO expansion board

IBASE IBR215 is a 2.5-inch Pico-ITX SBC powered by NXP i.MX 8M Plus quad-core ARM Cortex-A53 AI processor that supports 5G cellular connectivity via an M.2 3052 socket, and can be extended with an I/O expansion board with support for WiFi/BT, 4G/LTE, LCD, camera, NFC & QR-code functions. Equipped with up to 4GB RAM and 128GB flash storage, the single board computer has a ruggedized and fanless design that makes it suitable for industrial automation, smart home and buildings, smart cities and factories, retail environment, machine learning, and other industrial IoT applications. IBASE IBR215 specifications: SoC – NXP i.MX 8M Plus quad-core Arm Cortex-A53 processor @ up to 2.0 GHz with 512KB ECC cache, Arm Cortex-M7 @ up to 800 MHz, Vivante GC7000UL 3D GPU, Vivante GC520L 2D GPU, HiFi 4 DSP, 2.3 TOPS Neural Processing Unit (NPU) System Memory – 3GB DDR4 (optional 1/2/4GB) Storage 16GB eMMC flash (optional […]

August 14, 2021August 20, 2022 by Jean-Luc Aufranc (CNXSoft) - 19 Comments

NanoPi R2C is a cheaper dual GbE mini router with YT8521S Gigabit Ethernet PHY

FriendlyELEC’s NanoPi R2C is an updated version of NanoPi R2S dual GbE mini router that replaces Realtek RTL8211E Gigabit Ethernet transceiver with a Motorcomm YT8521S chip. NanoPi R2C mini router still comes with a Rockchip RK3328 quad-core Cortex-A53 processor, 1GB DDR4 memory, and a Realtek RTL8153 USB 3.0 to Ethernet controller for the second Ethernet port. NanoPi R2C specifications: SoC – Rockchip RK3328 quad-core Cortex-A53 @ 1.5 GHz with Arm Mali-450MP2 System Memory – 1GB DDR4 RAM Storage – MicroSD Slot, SPI flash footprint Connectivity 1x Gigabit Ethernet (WAN) up to 941 Mbps (measured) via MotorComm YT8521S Gigabit Ethernet transceiver 1x Gigabit Ethernet (LAN) up to 941 Mbps (measured) via Realtek RTL8153 USB 3.0 to Ethernet controller USB – 1x USB 2.0 Type-A host port, USB Type-C port Debugging – 3-pin 2.54mm pitch header for serial console Expansion – 10-pin GPIO header with GPIOs, I2C, UART, IR_Rx, 5V, 3.3V and GND […]