fpga News - Page 27 of 34 - CNX Software

July 7, 2016July 7, 2016 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

OpenCellular is Facebook’s (soon to be) Open Source Wireless Access Platform

A few months after Canonical and Lime Micro LimeSDR open source software defined radio aiming to be used as a development platform, but also as the base for low cost cellular or other wireless base stations, Facebook has announced their own open source wireless access platform with OpenCellular project whose goal is to lower the cost of Internet connectivity in remote areas where the infrastructure does not exist. This is how Marc Zuckerberg summarizes the project: We designed OpenCellular as an open system so anyone — from telecom operators to researchers to entrepreneurs — can build and operate wireless networks in remote places. It’s about the size of a shoe box and can support up to 1,500 people from as far as 10 kilometers away. Along with our solar-powered aircraft Aquila and high-bandwidth laser beams, OpenCellular is the next step on our journey to provide better, more affordable connectivity to […]

May 24, 2016May 24, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

LinkSprite O-board Altera Cyclone IV FPGA Development Board Targets OpenRISC Development

OpenRISC project‘s goal is to create a free and open processor for embedded system that include RISC instruction set architecture with DSP features, an open source implementations of the architecture, open source development tools and software, and simulators. You normally need FPGA board to emulate the processor before silicon is made available, so LinkSprite designed the O-board powered by Altera Cyclone IV FPGA to help with OpenRISC development and evaluation. O-board specifications: FPGA – Altera Cyclone IV E with 22K LUT (P/N: EP4CE22F17C8N) System Memory – 32MB SDRAM Storage – 1MB SPI FLASH, micro SD slot Connectivity – 1x Fast Ethernet (RJ45) USB – 1x micro USB for OTG HOST/SLAVE, 1 x micro USB for power supply, configuration, 2x UARTs, 2x JTAG… Expansion connectors – 2x 70-pin headers Power Supply – 5V via miro USB Dimensions – 96 x 40 mm The Wiki for the board explained how to get […]

May 9, 2016May 9, 2016 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Olimex iCE40HX1K-EVB Open Source Hardware Lattice FPGA Development Board To Sell for 22 Euros

Olimex has showcased a prototype of their small (5×5 cm) iCE40HX1K-EVB development board powered by Lattice Semi iCE40 FPGA, programmable with OLinuXino development boards via the UEXT interface, and compatible with Project Icestorm open source toolchain for Lattice iCE40. iCE40HX1K-EVB specifications: FPGA – Lattice Semi iCE40HX1K-VQ100 FPGA @ up to 533 MHz with 1280 gates, 160 Logic Array Blocks, and 64 kbit memory System Memory – 256Kx16 SRAM (Samsung K6R4016V1D-TC10 ) Storage – 2MB serial flash Expansion UEXT connector for programming 34-pin header to access FPGA I/Os Misc – 2x user buttons, reset button, 2x user LEDs Power Supply – 5V via power jack Dimensions – 5×5 cm (4-layer PCB) The company has also made four stackable add-on boards to connect to the 34-pin expansion header: iCE40-ADC fast 100Mhz ADC with BNC input connector for Digital Storage Oscilloscope (DSO) with up to 512 KB buffer iCE40-DAC fast 100Mhz DAC with […]

April 29, 2016April 29, 2016 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

LimeSDR Open Source Hardware Software Defined Radio Goes for $199 and Up (Crowdfunding)

Canonical and Lime Micro showcased SoDeRa software defined radio (SDR) a couple of months ago, with a promise to launch a crowdfunding campaign later this year. They’ve fulfill their promise, and launched the open source SDR, renamed to LimeSDR, on Crowdsupply. LimeSDR board specifications: FPGA – Altera Cyclone IV EP4CE40F23 Altera FPGA compatible with EP4CE30F23 System Memory – 256 MB DDR2 SDRAM RF Lime Microsystems LMS7002M RF transceiver with continuous coverage of the frequency range between 100 kHz and 3.8 GHz; 61.44 MHz bandwidth 4 x TxOut and 6 x RxIn U.FL connectors Power Output (CW): up to 10 dBm Wi-Fi, GSM, UMTS, LTE, LoRa, Bluetooth, Zigbee, RFID, Digital Broadcasting, configurable through apps. USB – 1x micro USB3 via CYUSB3014-BZXC Cypress Microcontroller for control, data transfer and power Misc – Status LEDs, RGB LEDs, 4x switches Power – USB or external power supply Dimensions – 100 mm x 60 mm The board […]

April 6, 2016April 6, 2016 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

PULPino Open Source RISC-V MCU is Designed for IoT and Wearables

lowRISC is not the only open source processor project based on RISC-V instructions, as researchers at ETH Zurich university and the University of Bologna have developed PULPino open-source processor based on RISC-V instructions set, optimized for low power consumption, and targeting wearables and the IoT applications. PULPino is a single core processor derived from the PULP project (Parallel Ultra-Low-Power Platform) featuring a quad core RISC-V SoC with new RI5CY Signal Processing ISA extensions designed by the universities. The core has an IPC (instructions per cycle) close to 1, full support for the base integer instruction set (RV32I), compressed instructions (RV32C) and partial support for the multiplication instruction set extension (RV32M). PULPino also features peripherals such as I2S, I2C, SPI and UART. PULPino has already been taped out as an ASIC in UMC 65nm at the beginning of the year, but the RTL code be run on Xilinx Zynq-7010 powered Zedboard, […]

April 1, 2016April 1, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Ultracker US360 360 Degrees Camera Features 4 Wide-Angle Lenses, Runs Android

We’ve already seen 360 degrees cameras with some rather expensive setups with multiple GoPros, as well as more affordable solutions (around $500) such as Gyroptic 360 Camera and ALLIe cameras. Taiwan based Ultracker Technology is now promising a 360 degree camera for around 300 dollars with their US360 model featuring four lenses for up to 1080p30 or 6144×1760 @ 6 fps video recording or live streaming. US360 camera specifications: FPGA implementation Camera Image Sensors – 4x 2.4 MP Sony Exmor CMOS Sensor Lens – 4x 2.3mm wide angle lenses View angle – 360° x 200° Image Settings Image Adjustment – Brightness, Contrast, Saturation, Sharpness, DWDR, AEC, AGC, AWB, Noise Reduction (2D/3D) Image Orientation – Flip, Mirror, 360˚ Rotation Photo format – JPEG Video Codec – H.264 or MJPEG Resolution & frame rate – 6144 x 1792 @ 6 fps , 1920 x 1080 @ 30 fps , 1280 x 720 […]

March 21, 2016March 21, 2016 by Jean-Luc Aufranc (CNXSoft) - No Comments

Avnet Introduces Zynq Based MicroZed Industry 4.0 / IIoT Ethernet Kit

There’s a lot of buzz around IoT, and the industrial sector is also trying to build smarter factories using protocols or standards part of Industry 4.0 or Industrial IoT (IIoT) depending on the country or group you belong too. Avnet has just launched MicroZed Industry 4.0 Ethernet Kit (I4EK) based on Xilinx Zynq-7000 ARM & FPGA SoC to address this market with support for the most common industrial protocols such as EtherCAT, Powerlink, PROFINET RT/IRT, EtherNet/IP, and Modbus-TCP. The “brain” of the development board is MicroZed module powered by Zilinx Zynq-7020 dual core Cortex A9 processor with FPGA fabric, and coupled with 1GB RAM, 128 MB SQPI flash, a Gigabit Ethernet port, and various I/Os. The module is connected to MicroZed FMC Carrier board with the following features: 2x 100-pin board-to-board MicroHeaders Xilinx PC4 header for download/debug – Accesses PL JTAG 5x Digilent Pmod compatible interfaces 39 user I/O 1x […]

February 16, 2016February 16, 2016 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

DAB Embedded OpenWrt Router Board Combines Atmel SAMA5D3 SoC and Altera MAX 10 FPGA

DAB Embedded, a Belgian engineering company specialized in research and development of electronic products, has designed DAB-OWT-SAM5 router board powered by Atmel SAMA5D36 Cortex-A5 processor and Altera MAX 10 FPGA, which runs OpenWrt or Windows Embedded Compact 7, and targets IoT applications. DAB-OWT-SAM5 board specifications: SoC – Atmel SAMA5D36 ARM Cortex-A5 processor @ 536MHz with Floating-Point Unit. FPGA – Altera MAX 10 FPGA with integrated ADC (Exact part number not disclosed) System Memory – Up to 512MB DDR2 Storage – Up to 2GB NAND flash, 1Mbit SPI flash, micro SD slot Connectivity – 2x Fast Ethernet ports, 802.11 b/g/n WiFi (Direct, station mode, and soft-AP) via Atmel ATWILC1000B module Display Interface – LVDS connected to FPGA USB – 1x USB 2.0 host, 1x USB 2.0 device Expansion Connectors Wired interfaces – RS232, CAN 2.0 A/B, KNX, RS-485/422, etc… Wireless connectivity – Zigbee, Z-Wave, KNX RF, etc… Power Supply – 5V DC […]