ethernet News - Page 9 of 21 - CNX Software

September 27, 2021November 15, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

ZB-GW03 ESP32-based Ethernet Zigbee gateway works with Tasmota firmware

ZB-GW03 is an Ethernet Zigbee Gateway compatible with eWelink mobile app and with a design similar to SONOFF ZBBridge gateway but replacing ESP8266 SoC by ESP32 SoC, and adding an Ethernet port. The ZB-GW03 gateway is apparently based on the same Silicon Labs EFR32MG21 Zigbee Arm Cortex-M33 chip and has been hacked to run Tasmota open-source software for people preferring more flexibility and/or integration with OpenHAB or Home Assistant open-source home automation frameworks via Zigbee2MQTT. ZB-GW03 gateway specifications: Main MCU – Espressif Systems ESP32 dual-core Tensilica TX6 processor @ 240 MHz with WiFi 4 and Bluetooth connectivity Zigbee MCU – Silicon Labs EFR32MG21 Arm Cortex-M33 MCU @ 80 MHz with Zigbee 3.0 connectivity Connectivity 10/100M Ethernet, WiFi, and Bluetooth via ESP32 Zigbee 3.0 via Silabs MG21 MCU with support for 128 nodes, up to 200+ meter range One 2.4 GHz Zigbee antenna One 2.4 GHz PCB antenna for WiFi Misc […]

August 17, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Raspberry Pi 4 gets IEEE1588 Precision Time Protocol (PTP) with Real-Time HAT

Raspberrry Pi 4 PTP protocol with the real-time HAT

InnoRoute Real-Time HAT adds IEEE1588 Precision Time Protocol (PTP) to Raspberry Pi 4/3 via a Xilinx Artix-7 FPGA and three Gigabit Ethernet ports. The Precision Time Protocol (PTP) is used to very accurately synchronize clocks throughout a computer network to enable measurement and control systems. It is often found in embedded microcontrollers or processors from Texas Instruments, STMicro, and more recently, in Intel Elkhart Lake & Tiger Lake H processors. It can notably be used for Time-Sensitive Networking (TSN) and Audio Video Bridging (AVB). InnoRoute Real-time HAT specifications & key features: FPGA- Xilinx Artik-7 FPGA Some RAM Networking Gigabit Ethernet port 0 with IEEE1588/TSN signaling Gigabit Ethernet port 1 with input from Raspberry Pi 4 Gigabit Ethernet port 2 with PoE, without TSN Host interface – 40-pin Raspberry Pi header mostly for SPI and I2C interfaces used for configuration. Misc – 3x LEDs, JTAG and PMod connectors, EEPROM (for Raspberry […]

July 15, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Low-cost embedded router SBC offers 2.5 GbE, WiFi 6 through Qualcomm IPQ5018 SoC

Wallys Communication has been offering Qualcomm-based embedded router boards for several years, including the higher-end DR8072A with dual 2.5GbE and WiFi 6 connectivity, followed by a lower-cost WiFi 6 SBC based on IPQ6010 with Gigabit Ethernet ports. But if you’d like to benefit from the lower cost while keeping WiFi 6 and 2.5GbE, the company has now introduced a new model based on Qualcomm IPQ5018 dual-core Cortex-A53 SoC, also found in Xiaomi Mi AX6000 router, with DR5018 embedded router board. The blurry photo above reveals the board is also called AP.MP03, a name that looks like the typical name for Qualcomm reference designs. DR5018 specifications: SoC – Qualcomm Atheros IPQ5018 dual-core Arm Cortex-A53 processor @ 1.0 GHz System Memory – 512MB DDR3L Storage – 4GB or 8GB eMMC flash, 4MB Nor Flash, 128MB NAND flash Networking 4x Gigabit Ethernet Ports or 1x 2.5Gbps Ethernet port 1x Gigabit Ethernet Port On-board […]

July 2, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

UP Connect Plus adds 5G support, 3 GbE ports to UP Core Plus, UP Xtreme SBCs

AAEON UP Connect Plus is a carrier board with three Gigabit Ethernet (GbE) ports, and an M.2 slot plus a micro SIM card socket adding support for 5G cellular connectivity to the company’s Appolo Lake-based UP Core Plus and Whiskey Lake-powered UP Xtreme single board computers. UP Connect Plus specifications: Connectivity 3 Gigabit Ethernet RJ45 ports in two configurations: 3x Intel Ethernet Controller I211-AT 3x Intel Ethernet Controller I210-IT with wide temperature and TSN (Time-sensitive Networking) 5G cellular – M.2 3042/3052 colay socket with micro-SIM card port to support 4G/5G modules USB – 1x USB 3.0 Type-A port for UP Core Plus only PCIe – 1x 2 channel PCIe switch SBC connectors – 2x 100-pin high-speed docking connectors Power Supply – 12V/5V from the main board Power Consumption – Approximately 36 to 40 Watts with UP Core Plus + UP Connect Plus Dimensions – 90 mm x 56 mm Temperature […]

June 21, 2021June 21, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

10BASE-T1L Ethernet chips enable up to 1.7 kilometer long Ethernet cables

The maximum length of Ethernet cables used to be 100 meters. While that may be more than enough for most applications, it does not cut it for industrial communication applications. So the 10BASE-T1L Ethernet physical layer standard (IEEE 802.3cg-2019) was approved by the IEEE on November 7, 2019 to allow for cables over one kilometer using a single twisted-pair cable. Analog Devices has launched two 10BASE-T1L Ethernet chips with ADIN1100 Ethernet PHY and ADIN1110 Ethernet MAC-PHY that allow for up to 1.7 kilometer long Ethernet cables. Let’s check out ADIN1100 specifications for reference: 10BASE-T1L IEEE Std 802.3cg-2019 compliant Cable Reach 1700 meters+ with 1.0 V pk-pk 1700 meters+ with 2.4 V pk-pk Auto-Negotiation capability Supports intrinsic safety applications MII, RMII & RGMII MAC interfaces MDIO Management Interface Unmanaged configuration using pin strapping including: Master/Slave selection Transmit amplitude PHY address 25 MHz crystal oscillator/25 MHz external clock input (50 MHz external […]

May 18, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

OpenMV PureThermal STM32H7 board overlays thermal map on RGB image

We’ve been writing about OpenMV open-source camera boards programmable with MicroPython at least since 2015, with the latest model OpenMV Cam H7 based on STM32H7 Cortex-M7 microcontroller introduced in 2018. But the company has now gone a step further with OpenMV PureThermal board equipped with a more powerful STM32H7 dual-core Arm Cortex-M7/M4microcontroller, and supporting FLIR Lepton 2 to 3.5 thermal imagers, allowing the system to overlay the thermal map on top of the image like an augmented reality app would do. It can do so on the integrated LCD display or on an HDMI display. OpenMV PureThermal features & specifications: MCU – STMicro STM32H7 Arm Cortex-M7 @ 480 MHz) and Cortex-M4 @ 240 MHz microcontroller Memory – 64MB SDRAM Storage – 32 MB of QSPI flash for the firmware, a microSD card slot for saving pictures and machine vision assets Display 800×480 touch Screen LCD DVI out for driving an […]

May 12, 2021May 12, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Gateworks GW7200 Dual Gigabit Ethernet industrial SBC, also supports WiFi, Cellular, and GPS

Gateworks GW7200 dual GbE industrial SBC

Gateworks GW7200 is a versatile dual Gigabit Ethernet industrial single board computer with an NXP i.MX8M Mini processor, 1GB to 4GB of RAM, mini PCIe expansion sockets for wireless connectivity, serial interfaces, industrial temperature range, wide range input voltage, and long-term supply. The board should be a better match to projects with industrial requirements, for example, an industrial IoT gateway than lower-cost dual GbE alternatives such as NanoPi R2S or Raspberry Pi CM4 IoT Router Carrier Board Mini. Gateworks GW7200 specifications: SoC – NXP i.MX 8M Mini quad-core processor @ 1.6GHz with Vivante 2D & 3D GPUs System Memory – 1GB to 4GB DDR4-2133 SDRAM Memory Storage – 8GB to 64GB eMMC flash, MicroSD card slot, serial configuration EEPROM Connectivity Dual GbE Ethernet ports supporting 802.3at/af and passive PoE Optional 802.11ac/n WiFi 5/4 via mini PCIe socket Optional Cellular (Cat M1, 4G, 5G) via mini PCIe socket + NanoSIM card […]

April 19, 2021April 19, 2021 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Dual Ethernet SigmaStar SSD201/SSD202 SBC supports 4-inch or 7-inch displays

SigmaStar SSD201/SSD202 are low-cost, highly integrated SoC’s with a dual Cortex-A7 processor, 64MB to 128MB on-chip RAM designed for Full HD smart displays, but we’ve also found SSD201 in a 4G LTE industrial gateway. There’s now a different type of board based on the SigmaStar processors with Wireless Tag/Industio IDO-SBC2D06-V1B-12W and IDO-SBC2D06-V1B-22W SBC’s powered respectively by SSD201 and SSD202, and both equipped with dual Ethernet and a connector for a 4-inch or 7-inch display. Specifications: System-on-Module (one or the other) IDO-SBC2D06-V1B-12W SBC – IDO-SOM2D01 module with SigmaStar SSD201 dual-core Cortex-A7 processor @ 1.2 GHz with 2D GPU, 64MB DDR2, 2Gbit SPI NAND flash IDO-SBC2D06-V1B-22W SBC – IDO-SOM2D01 module with SigmaStar SSD202 dual-core Cortex-A7 processor @ 1.2 GHz with 2D GPU, 128MB DDR3, 2Gbit SPI NAND flash Storage – MicroSD card slot Display – 4-lane MIPI DSI connector for 4-inch RGB565 display or 7-inch RGB888 display Audio – 2-pin Microphone connector […]