esp8266 News - Page 20 of 21 - CNX Software

May 29, 2015May 28, 2015 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

ESP8266 SDK 1.1.0 is Now Released Under an MIT License

ESP8266 is the now famous dirt-cheap Wi-Fi SoC used for IoT applications. It can be used by hobbyists and companies alike. But for the later, there was a licensing issue as Espressif ESP8266 SDK was initially released under the GPLv3 license. GPL code is great and lots of open source projects are released under the most common open source license. But since proprietary, closed source software has still its place in the market place, some other more permissive licenses such as LGPL are used for library, and Android for example has an Apache License 2.0. So previously, if you developed an application using ESP8266 SDK, you’re code would have to be GPL too, since the license is viral. It would also cause issues if you had released your application under an Apache or MIT license. But now, all is well, as Espressif released ESP8266 SDK 1.10 under an MIT license, […]

April 25, 2015April 25, 2015 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

$10 Digistump Oak ESP8266EX Board is Arduino Compatible, Connects to the Cloud, and More (Crowdfunding)

A few years ago, I wondered why adding Wi-Fi to Arduino had to be rather expensive ($40+), and why there weren’t any low cost and small form factor Wi-Fi boards for embedded applications. But we’re now in 2015, embedded is “dead” giving rise to IoT, and I’m left wondering how it’s possible to make IoT Wi-Fi modules that cheap, and whether people will ever stop churning out cheap Wi-Fi boards, as I’m flooded with such news weekly… So when I saw yet another ESP8266 board on Kickstarter I was about to dismiss it, but since it was made by Digistump, that has an active community with their other products like DigiSpark Pro or DigiX, I decided to have a closer look. Digistump Oak hardware specifications: MCU – Espressif ESP8266EX 32-bit microprocessor @ 80MHz (overclockable up to 160MHz) with 1MB ROM (~300KB available for user code), 64KB RAM, 512 bytes EEPROM […]

April 18, 2015April 18, 2015 by Jean-Luc Aufranc (CNXSoft) - 15 Comments

NodeMCU is both a Breadboard-Friendly ESP8266 Wi-Fi Board and a LUA based Firmware

NodeMCU is a LUA based interactive firmware for Expressif ESP8622 Wi-Fi SoC, as well as an open source hardware board that contrary to the $3 ESP8266 Wi-Fi modules includes a CP2102 TTL to USB chip for programming and debugging, is breadboard-friendly, and can simply be powered via its micro USB port. Let’s checkout the hardware first. The latest version of the board (V1.0) has the following specifications and features: Wi-Fi Module – ESP-12E module similar to ESP-12 module but with 6 extra GPIOs. USB – micro USB port for power, programming and debugging Headers – 2x 2.54mm 15-pin header with access to GPIOs, SPI, UART, ADC, and power pins Misc – Reset and Flash buttons Power – 5V via micro USB port Dimensions – 49 x 24.5 x 13mm The hardware documentation for the board can be found on nodemcu-devkit repo, including schematics and PCB layout designed with Altium Designer, […]

April 3, 2015 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

ESP8266 Wi-Fi Module is Now Supported in Arduino IDE

ESP8266 revolutionized the IoT world by offering an ultra low cost Wi-Fi solution either standalone or connected to a micro-controller board via SPI or UART. There are plenty of tutorials on the web to play with the Wi-Fi module, but it’s only recently an Arduino IDE has added support for ESP8266. If you want to try it, you can download the binary for Linux, Windows, or Mac OS X. Since my computer is running Ubuntu 14.04, I download and extracted arduino-1.6.1-linux64.tar.xz to install it in my PC. Now simply run the arduino script to start the IDE, and select to Tools->Board->Generic ESP8266 board. I don’t own an ESP8266 module myself, but Olimex tried it on their ESP8266-EVB: They connected a serial debug board and selected Tools->Port->/dev/ttyUSB0 in the IDE Selected Tools-> Programmer->esptool Loaded Blink example, and modified it to turn on and off the relay on their evaluation board. If […]

February 18, 2015 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Freetronics Introduces an Arduino Shield for ESP8266 ESP-01 Wi-Fi Module

ESP8622 has drastically brought down the price of adding Wi-Fi to MCU boards such as Arduino UNO, but you need to add some cables, and take care of 3.3V to 5V conversion for the UART pins either with a divider made of 2 resistors, or a FET level shifter, and you may not be able to access all I/O of ESP8622 on the popular ESP-01 version of the module. For a neater solution, Freetronics had designed ESP-01 WiFi Module Shield that takes care of all these small issues. Key features of the shield: 3.3V regulator dedicated to the module Logic level shifters on TX/RX lines: compatible with both 3.3V and 5V Arduino models Selectable TX/RX pins: use D0/D1 for hardware serial, or D2 – D7 for software serial CH_PD pin on ESP-01 module pre-biased for correct operation mode Extra ESP-01 pins broken out for your own connections Prototyping area with […]

January 27, 2015 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Olimex ESP8266-EVB Wi-Fi Evaluation Board Includes a Relay, an UEXT Connector

Olimex announced open source hardware ESP8266 modules last month, and the company has just announced the availability of ESP8266-EVB board with an ESP8266 module, a relay, an UEXT connector for other compatible Olimex modules, and headers for access to GPIOs. ESP8266 evaluation board specifications: MOD-WIFI-ESP8266-DEV Wi-Fi module with soldered connectors Female connectors for MOD-WIFI-ESP8266-DEV 10A/250VAC Relay Expansions 16-pin header (CON3) with access to some GPIOs, ADC, SDIO, RESET, and power signals. UEXT connector to connect modules and sensors from Olimex, or access I2C, UART, SPI, and extra GPIOs Misc – User Button which can also be pressed at boot time to enter bootloader mode for firmware upgrade. Power Supply – 5V/1A recommended; DCDC power converter to 3.3V to supply ESP8266 and UEXT modules with up to 1.5A current Dimensions – 57x50mm (4 mounting holes) You’ll also need 5V power supply, and a USB to serial board (3.3V) in order to […]

December 31, 2014May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 17 Comments

Olimex Introduces Open Source Hardware ESP8266 Wi-Fi Modules, Evaluation Board Coming Soon

ESP8266 has become popular as module based on this SoC make it incredibly cheap to add Wi-Fi to all sort of things, the SDK available, and a community has gathered around the solution. Olimex has jumped on the bandwagon, and is now provided two open source hardware ESP8266 modules: MOD-WIFI-ESP8266 which makes it easy to interface to other Olimex boards thanks to its UEXT connector, and MOD-WIFI-ESP8266-DEV with two rows of 0.1″ connectors and an unsoldered UEXT pad, is better suited if you want to integrate it with your own baseboard, or experiment with a breadboard. An evaluation board called MOD-WIFI-ESP8266-EVB will be launched a little later. Both modules share most specifications: SoC – Espressif Systems ESP8266 32-bit RISC processor with 802.11 b/g/n support(32-pin QFN package), Wi-Fi – 802.112 b/g/n with WEP, TKIP, AES, and WAPI engines, Wi-Fi direct (P2P), and soft-AP. On-board antenna and u.FL connector Expansion MOD-WIFI-ESP8266 – […]