e-con Systems News - Page 3 of 3 - CNX Software

March 18, 2016March 18, 2016 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

e-Con Systems Propus Nvidia Tegra K1 Development Board Features 3 MIPI-CSI Camera Interfaces

I mostly know e-Con Systems because of their camera modules, but the Indian company has also been manufacturing system-on-modules and development kits, and has just launched Propus development board based on their eSOMTK1 computer-on-module powered by Nvidia Tegra K1 quad core Cortex A15 processor, and including three camera interfaces with two 4-lane and one 1-line MIPI-CSI2 connectors. Propus specifications: Computer-on-module – eSOMTK1-F16G-R2G-WB-IM: SoC – Nvidia Tegra K1 4-plus-1 ARM Cortex-A15 processor @ up to 2.3 GHz with 192-core Kepler GPU. System Memory – 2GB 64-bit DDR3L SDRAM Storage – 16GB eMMC flash Connectivity – 802.11 a/b/g/n and Bluetooth 4.1 module with 2 u.Fl antenna connectors Sensors – 3D digital accelerometer and a 3D digital gyroscope (6 axis) Power Management IC (5V and 12V inputs) SoM connectors – 4x 100-pin board to board connectors Storage – SATA connect, micro SD slot Video Output – 1x HDMI 1.4 Audio – Audio Codec […]

August 19, 2015August 19, 2015 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Ascella USB 3.0 Camera Reference Design Kit Supports 4K Recording at 30 fps

Cypress Semiconductor and THine Electronics have recently introduced Ascella USB 3.0 camera reference design kit based on Cypress EZ-USB CX3 USB 3.0 camera controller and THIne THP7312 ISP that supports 13-megapixel resolution at 21 frames per second, and 3840x2160p recording at 30 fps using MJPEG compression. The kit is composed of 5 boards with an OV13850 13MP camera board, an LED board, the ISP board, Cypress CX3 board, and a debug board with USB 3.0 and a debug interfaces. Main specifications and features: Cypress EZ-USB CX3 ARM9 based Programmable MIPI CSI-2 to USB 3.0 Camera Controller THine THP7312 image signal processor based on a 32-bit RISC CPU OmniVision OV13850 Image sensor interfaced through a four-lane MIPI CSI-2 interface High Intensity LED Board for Low light environment SPI Flash for firmware storage Supports auto-focus, auto-exposure, auto-white-balance and the ability to select from 20 picture resolutions Support for streaming of live […]

April 23, 2015April 23, 2015 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

e-con Systems 13MP MIPI CSI-2 Camera Designed for Nvidia Jetson TK1 Board

e-con Systems has just introduced e-CAM130_CUTK1, a 13 MP MIPI CSI-2 camera board specifically designed for Nvidia Jetson TK1 development board powered by Nvidia Tegra K1 quad core Cortex A15 processor supporting up to Ultra HD (3840×2160) resolution @ 22 fps, or 1080p @ 30+ fps with MJPEG or YUV422 output. e-CAM130_CUTK1 camera board is comprised of a camera module and an adapter board that can be directly plug into Jetson TK1 board. Camera board key features and specifications: Camera Module e-CAM130_CUMI1820_MOD with S-mount lens holder based on Aptina AR1820HS sensor. Max S/N ratio: – 36.3 dB; Dynamic Range: – 65.8 dB Interface – 4-lane MIPI CSI-2 interface Resolution / Frame rate – VGA @ 90 fps, 720p @ 60 fps, 1080p @ 30 fps, UltraHD (3840×2160) @ 22 fps, 13MP (4224×3156) @ 14 fps. Values are the same for MJPEG or YUV422. Connector – 125-pin connector for Jetson TK1 […]

December 4, 2014May 1, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

e-con Systems Unveils eSOMiMX6 SoM based on μQ7 Form Factor, and Ankaa Development Kit

QSeven is one of the many standards for system-on-modules, and it defines both Qseven (Q7) 70x70mm modules, and smaller μQSeven (μQ7) 70x40mm modules. While there are quite a few SoMs following the larger form factor, few modules are based on micro Q7, and e-con Systems eSOMiMX6 has just launched one of these tiny modules with eSOMiMX6 system-on-module powered by Freescale i.MX6 processors, as well the corresponding Ankaa development kit comprised of the SoM and a baseboard. eSOMiMX6 module specifications: SoC – Freescale i.MX6 single, dual or quad Cortex A9 processor @ 800MHz to 1.2 GHz with Vivante GPUs System Memory – 256MB/512MB (Solo only), 1GB (default), or 2GB (dual/quad only) LVDDR3 RAM Storage – 4GB (default) to 64GB eMMC flash, 2MB SPI NOR flash, and SD/MMC + SATA II interfaces via MXM connector Display / Video Output: HDMI up to 1920 x 1080 Dual channel 24-bit LVDS 24-bit LCD RGB MIPI […]

June 1, 2012June 1, 2012 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

e-con Systems Unveils e-CAM51_USB 5MP USB Camera Module

e-con Systems, an embedded design services company specializing in the development of camera solutions, has just announced the launch of e-CAM51_USB USB Camera comprised of a 5-megapixel Autofocus Camera Module (e-CAM52_5640_MOD) based on OmniVision OV5640 CMOS image sensor.This camera module targets document camera visualizers, interactive teaching & meeting solutions, OCR, scientific research, telemedicine/health, biometrics and robotics applications. The e-CAM51_USB camera module supports GPIO and microphone with an integrated analog-to-digital converter (ADC). It does not require specific drivers since it is compliant with USB Video Class (UVC) and USB Audio Class (UAC). OmniVision OV5640 CameraChip sensor features automatic image control functions such as: Automatic exposure control (AEC) Automatic white balance (AWB) Automatic band filter (ABF) 50/60Hz automatic luminance detection Automatic black level calibration (ABLC) Most of these features are supported via the standard UVC protocol providing good applications interoperability on Linux and Windows. Some e-CAM51_USB features such as GPIO control, Auto […]