display News - Page 31 of 40 - CNX Software

December 4, 2020December 4, 2020 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

$25 TTGO T5 4.7-inch e-Paper Display comes with ESP32 WiFi & Bluetooth SoC

We’ve very recently covered M5paper IoT development kit based on ESP32 WiSoC, and equipped with a 4.7-inch touchscreen e-Ink display together with a 1,150mAh battery all nicely packed into an enclosure. It looks great, but costs $69, so if you’d like to integrate this type of ESP32 connected display into your own project at a lower cost, you may be interested in TTGO T5 4.7-inch e-Paper display with 16 gray levels fitted with an ESP32-WROVER-E module with 16MB flash, and 8MB PSRAM. TTGO T5 key features and specifications: Display 4.7-inch ePaper display with 960×540 resolution, 16 gray levels , partial refresh support 6-pin FPC touchscreen connector Wireless module – ESP32-WROVER-E with ESP32-D0WDQ6 V3 dual-core processor, 16MB flash, 8MB PSRAM USB – 1x USB-C port Expansion – 4-pin connector with GPIOs, GND, 3.3V Misc – 1x reset button, 4x user buttons Debugging – USB-C port connected to USB to TTL CP2104 […]

November 26, 2020February 22, 2021 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

MorphESP 240 ESP32-S2 board integrates a 1.3-inch color display (Crowdfunding)

MorphESP 240 ESP32-S2 board with color display

We’ve already seen ESP32 platforms with a color display such as M5Stack, but MorphESP 240 is kind of cute with a 1.3-inch color display, features the more recent ESP32-S2 WiFi processor, and supports battery power & charging. MorphESP 240 specifications: Wireless Module – ESP32-S2-WROOM with Espressif Systems ESP32-S2 single-core 32-bit Xtensa LX7 microprocessor up to 240 MHz with 128 KB ROM, 320 KB SRAM, 16 KB SRAM in RTC, 4MB SPI flash, 802.11 b/g/n 2.4 GHz Wi-Fi connectivity Display – Onboard 1.3-inch ST7789 display with 240 x 240 resolution, connected over SPI USB – 1x Micro USB port for power/charging and programming Expansion – 16-pin and 24-pin headers with GPIO, I2C, UART, SPI, USB, and power signals Misc – WS2812B RGB LED connected to IO16, Reset button, boot mode switch, battery on/off switch Power Supply 5 V to 3.3 V regulator to feed additional modules JST connector for a battery […]

November 24, 2020November 24, 2020 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Raspberry Pi 400 kit ships with 7-inch or 13.3-inch touchscreen display

The Raspberry Pi Foundation has recently launched the Raspberry Pi 4 keyboard computer with impressive performance thanks to a well-designed cooling solution, and I think it’s a great tool for kids (and adults) who may want to carry a Raspberry Pi around. However, you’d still need a display in each location, so until the foundation releases the Raspberry Pi 4000 laptop next year (full disclose: I made that up!), it might be cool to have a portable display coming with the keyboard PC. That’s what Waveshare is offering with two kits combining a Raspberry Pi 400 together with a 7-inch or 13.3-inch HDMI touchscreen display and other accessories. Not quite as portable as a laptop but it gets close. Here’s the full list of accessories in the kits: Raspberry Pi 400 Kit with keyboard PC with UK keyboard (sadly the only layout option for now), power supply, HDMI cable, preloaded […]

November 13, 2020November 14, 2020 by Jean-Luc Aufranc (CNXSoft) - 22 Comments

WT32-SC01 is a thin 3.5-inch ESP32 color touchscreen display

Looking for an ESP32 board with a color touchscreen display? There is plenty of choices here, including Espressif Systems own ESP32-S2-Kaluga-1 multimedia devkit with a 3.2-inch display or M5Stack Core2 with a 2-inch display. But if you’d like a thinner and larger display, Tag Wireless WT32-SC01 is an ESP32-powered 3.5-inch color display with a 2-point capacitive touchscreen designed to be integrated into your own project or product. WT32-SC01 WiFi display specifications: Wireless Module – ESP32-WROVER-B module based on ESP32-D0WD dual-core processor up to 240 Mhz with 4MB SPI flash, 8MB PSRAM, 2.4GHz WiFi 802.11 b/g/n up to 150 Mbps, and Bluetooth 4.2 LE Display – 3.5-inch 480×320 display (SPI) with 2-pin capacitive touchscreen (I2C) Expansion – 2x 40-pin I/O pads with GPIO, I2C, VN/VP, I2S, UART, 5V, 3.3V, GND Misc – Reset button (6), power and UART LEDs Power Supply – 5V/1A via USB type-C port for display only, or […]

September 1, 2020September 1, 2020 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

M5Stack Launches Core2 ESP32 IoT Development Kit with 2-inch Touch Display

M5Stack has just launched an upgrade to its M5Stack Core development with M5Stack Core2 based on the same Espressif ESP32 WiFI + Bluetooth SoC, but adding capacitive touchscreen support to the 2-inch TFT LCD, as well as a motion sensor and a microphone. The new version also adds 8MB PSRAM, a larger 390 mAh battery, and targets IoT terminals for Smart Home, industrial automation or robotics, STEM Education, and DIY prototyping. M5Stack Core2 specifications: SoC – Espressif ESP32-D0WD-V3 dual-core Xtensa LX6 processor clocked at up to 240MHz with 520KB SRAM, Wi-Fi, and dual-mode Bluetooth connectivity External Memory – 8MB PSRAM Storage – 16MB flash storage, MicroSD card slot up to 16GB Display – 2-inch IPS LCD screen with 320×240 resolution (ILI9342C driver), and touchscreen support (via FT6336U controller) Audio – 1W speaker (1W-0928), SPM4123 microphone, NS4168 I2S power amplifier Antenna – 2.4GHz 3D antenna USB – 1x USB Type-C port […]

August 19, 2020August 19, 2020 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Keyboard FeatherWing Brings Keyboard & Display to Adafruit Feather Boards

Solder Party is a brand new Swedish startup founded by Arturo182 who previously designed several maker boards including the tiny Serpente R2 CircuitPython prototyping board, and its first product, named Keyboard FeatherWing, brings a QWERTY keyboard and 2.6” color LCD with resistive touch screen to any boards compatible with Adafruit Feather for factor. That means you can build a portable device that runs Linux via the Giant Board, features an FPGA (Orange Crab), or a wide range of connectivity options including WiFi, Bluetooth LE, LoRa, etc… depending on your chosen board. The solution actually brings a bit more than just a keyboard and color, as shown by the list of Keyboard FeatherWing key features: Display – 2.6” 320×240 16-bit color LCD with resistive touch screen (SPI) Storage – MicroSD card slot (SPI) User Inputs controlled by a Microchip SAMD20 MCU QWERTY keyboard (I2C) 5-way button 4 soft tactile buttons Expansion […]

July 24, 2020July 24, 2020 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

12.5-inch 4K IPS Touchscreen Display Works with Raspberry Pi 4B and other 4K SBC’s

There are plenty of displays for the Raspberry Pi boards, but if you are looking for a high-resolution display with capacitive multi-touchscreen it may be challenging to find. DFRobot may have what you are looking for though with a 12.5″ 4K IPS touchscreen display. The company says it’s compatible with Raspberry Pi 4B SBC, but since it comes with a mini HDMI input port, it should really work with any 4K capable SBC’s or computers. Key features & specifications: 12.5-inch IPS Pro display with 4K UHD (3840×2160) resolution, 60 Hz refresh rate, HDR, 10-point touch 100% Color gamut, 400cd/㎡ brightness, 178° viewing angle Video Input – Mini HDMI input Audio – Built-in left and right loudspeaker, 3.5mm audio jack (output) USB – 2x USB Type-C ports both supporting touch/data and power Misc – Function menu button, power LED, power button Power Supply – Via USB-C port (USB-PD supported) Dimensions – […]

July 20, 2020July 20, 2020 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Waveshare Launches an Affordable 7-Color e-Paper Display

Most e-paper displays are black or white with sometimes red or yellow color being added to the mix. But E-Ink has recently launched several color e-Paper display at prices that will not make it affordable to most projects. Waveshare has launched its fair share of e-Paper displays in the past, and now the company is coming with a relatively affordable 5.65″ color e-Paper display with seven different colors for $74.99 plus shipping. Main features and specifications: Display 5.65″ display (114.9 × 85.8mm) Resolution – 600 × 448 pixels Viewing angle – >170° ACeP (Advanced Color ePaper) 7-color with black, white, green, blue, red, yellow, and orange Greyscale – 2 levels Full refresh time – 15s Dot pitch – 0.1915 × 0.1915mm Host Interface – 3-wire SPI or 4-wire SPI Operating voltage – 3.3V/5V Power Consumption 50mW (typ.) during refresh Standby current – <0.01uA (almost none) Dimensions – Board – 138.5 […]