development board News - Page 277 of 277 - CNX Software

September 28, 2011November 1, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

CraneBoard: Low Cost Development Board based on TI AM3517

The CraneBoard is a low-cost, open-source hardware development platform based on the AM3517 Sitara ARM Cortex-A8 microprocessor. The CraneBoard was announced in December 2010, can be purchased for 199 USD and can be an alternative to the Beagleboard-xM. AM3517 is especially suited to industrial applications and would be a preferable platform if your project needs CAN or PoE support. The board has less RAM (256 MB vs. 512MB) and no camera port. Here are the features and specifications of the board (I highlighted the differences with Beagleboard-xM in green): AM3517 Sitara ARM Cortex-A8 – 600MHz Integrated 3D Graphics Accelerator RAM: 256 MB NAND Flash: 256MB Support for on-chip peripherals: 10/100 EMAC USB OTG utilizing on-processor PHY 3.3V I/O CAN Bus DDR2 Power over Ethernet and other power options including USB and DC MMC/SD Card Support Fully open-source four-layer PCB Fully Open Source Linux Board Support package (2.6.32) Based on existing […]

September 22, 2011September 22, 2011 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

99 USD OMAP3 Based Overo Computer On Module by Gumstix

Gumstix has manufactured its Overo COMS based on OMAP3503 and OMAP3530 since 2008. They have now announced a new low cost version named Overa Sand that sells for 115 USD per unit or less than 99 USD per unit for orders of 1,000 units or more. Overo Sand COM is Gumstix’s most basic computer-on-module with 256MB RAM and no on-board NAND. Here are the board specifications and features: Processor: Texas Instruments OMAP 3503 Applications Processor: – ARM Cortex-A8 CPU @ 600 Mhz Memory: 256MB RAM NO On-Board NAND Included Features: microSD card slot TPS65950 Power Management Expandability: via one 140-pin expansion board of Gumstix Overo series or custom, 140-pin expansion board via 27-pin camera board Connections: – (2) 70-pin connectors with 140 signals for: – I2C, PWM lines (6), A/D (6), 1-wire – UART, SPI, Extra MMC lines – Headset, Microphone – Backup battery – High Speed USB Host and […]

September 20, 2011September 20, 2011 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

First ARM-Based Arduino Board with Atmel SAM3U

Arduino announced Arduino Due board with a 32bit Cortex-M3 ARM processor on their blog before Maker Faire. The SAM3U processor from ATMEL runs at 96MHz with 256Kb of Flash, 50Kb of SRAM, 5 SPI buses, 2 I2C interfaces, 5 UARTS, 16 Analog Inputs at 12Bit resolution and more. Contrary to previous hardware release, they intend to open the process to the community early on and they plan to to be demo the board and give away some boards to a selected group of developers who will be invited to shape the platform while it’s been created. After Maker Faire, a small batch of Developer Edition boards on the Arduino store will be sold to members of the community who want to join the development effort. The final board will be released by the end of 2011. If you can’t wait there are some other Arduino-like projects with Cortex-M3 support based […]

September 14, 2011September 14, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

Ziilabs Unveils Low Cost Jaguar3 Android Tablet Reference Designs

Earlier this May, Ziilabs announced the ZMS-20 dual core processors targeted at Android Honeycomb tablets. They have now unveil the 3rd generation of Android Tablet reference designs based on ZMS-20 and ZMS-40 called Jaguar3. Here’s an excerpt of the press release: ZiiLABS, a pioneering media processor and platforms company (a wholly-owned subsidiary of Creative Technology Ltd), today introduced its JAGUAR3, the most powerful 3rd Generation Android 3.2 tablet series. JAGUAR3 is a series of ultra-slim, ultra-lightweight and stylish 10.1” tablet reference designs targeted at the OEM markets. With over a decade of designing experience in portable mobile devices, Creative provided the ergonomic and sexy design of this series of JAGUAR3 tablets. ZMS-20 StemCell Processors JAGUAR3’s superior performance, low power consumption and rich feature set comes from the dual-core 1.5GHz ARM Cortex-A9 based ZMS-20 StemCell Processors. ZMS-20 has another 48 StemCell Processing cores within, which effectively make it into a 50-core processor. […]

September 12, 2011September 12, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

Android 2.3.4 Release For ST Ericsson Snowball Development Board

Igloo Community – the team developing for ST Ericsson Snowball Nova A9500 development board – has released the first version of Android 2.3.4 for the board. It can be downloaded at http://igloocommunity.org/download/android/images/20110910/. Here are the main features for this release: Based on Android 2.3.4 HDMI/DVI-D display support Graphics acceleration with the Mali 400 GPU Bluetooth support Multimedia acceleration Ethernet connectivity microSD card support Sensors support ADB over ethernet (by default) and over USB OTG port and the Known issues: WLAN connectivity is disabled in the UI due to startup problems with the interface. Audio recording does not work Consecutive audio playback might not work Potrait mode does not work (rotating the device corrupts screen until rotated back) Might be a temporary problem, but the browser crashes on the default google page when loading finishes. Other pages seem to work fine, so interrupting loading or going through the search acts as […]

September 11, 2011September 11, 2011 by Jean-Luc Aufranc (CNXSoft) - No Comments

Advantech PCM-C3500 Series OMAP35xx SBC

Advantech announced the PCM-C3500 Series single board computers (SBC) powered by TI OMAP3503 or OMAP3530 processors with 128 to 256 MB SDRAM and 1 to 2 GB Flash (optional) . These heatsink-free boards are targeted for various low-power applications in industrial control, HMI/kiosk, medical, and portable applications.The boards will run Windows CE 6.0 (default), Embedded Linux 2.6 and Android 2.2. Here are the specifications for PCM-C3500 SBC: CPU – PCM-C3530: TI OMAP3530 @ 600 MHz / PCM-C3503: TI OMAP3503 @ 600 MHz DSP – Built-in 430-MHz TMS320C64x+™ DSP Core (PCM-C3530 only) 2D/3D Accelerators – OpenGLES 1.1 and 2.0, OpenVG1.0 (PCM-C3530 only) OS – WinCE6.0 English professional version as default, and Linux DRAM – PCM-C3530: 256 MB, PCM-C3503: 128 MB (Optional: 256 MB) Onboard Flash – PCM-C3530: Default 2 GB, (Optional: 0 GB, 1 GB) /PCM-C3503: Default 0 GB, (Optional: 1 GB, 2 GB) RTC Watchdog Power Management – Standard, idle […]