debian News - Page 65 of 83 - CNX Software

April 29, 2016April 29, 2016 by Jean-Luc Aufranc (CNXSoft) - 18 Comments

NanoPC-T3 Octa-core Cortex A53 Single Board Computer Sells for $60

FriendlyARM launched NanoPC-T2 single board computer based on Samsung 5P4418 quad core Cortex A9 processor about 3 months ago, and the company has now an update based on Samsung S5P6818 Octa-Core A53 processor with the exact same interfaces and features including Gigabit Ethernet, WiFI, and Bluetooth, HDMI 1.4a, 30-pin expansion headers, etc… NanoPC-T3 specifications: SoC – Samsung S5P6818 octa core Cortex A53 processor @ up to 1.4GHz with Mali-400MP GPU System Memory – 1 or 2GB 32bit DDR3 RAM Storage – 8GB eMMC flash, and 1x SD card slot Connectivity – Gigabit Ethernet (RTL8211E), 802.11 b/g/n WiFi and Bluetooth LE 4.0 (Ampak AP6212) with on-board chip antenna and IPX antenna connector Video Output / Display I/F- 1x HDMI 1.4a, LVDS, MIPI DSI, parallel RGB LCD Audio I/O – HDMI, 3.5mm audio jack, on-board microphone Camera – 1x DVP interface, 1x MIPI CSI interface USB – 2x USB 2.0 type A host […]

April 26, 2016April 26, 2016 by Jean-Luc Aufranc (CNXSoft) - 35 Comments

Orange Pi Plus 2E Development Board with Gigabit Ethernet, 2GB RAM & 16GB eMMC Flash to Sell for $35

Shenzhen Xunlong has been pretty busy churning out new boards over the last few months and years, but is still not active on the software side. However these days, it’s not that bad thanks to Armbian community which provides Debian based images, and supports Allwinner H3 boards pretty well. The company is now about to launch Orange Pi Plus 2E, based on Orange Pi Plus 2 which comes with 2GB RAM, but at a lower cost, by removing SATA, the need for a USB hub chip, and the camera connector, while still managing to upgrade the eMMC flash capacity to 16 GB. Orange Pi Plus 2E specifications with differences in bold or stricken through: SoC – Allwinner H3 quad core Cortex A7 @ 1.3 GHz with ARM Mali-400MP2 GPU up to 600 MHz System Memory – 2GB DDR3 Storage – 16GB eMMC, micro SD card slot, SATA interface (via a […]

April 2, 2016May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 22 Comments

Low Cost Development Boards Linux Benchmarks – Raspberry Pi vs Banana Pi vs Orange Pi vs ODROID

LoveRPi, a distributor and reseller of electronic boards and accessories, has run benchmarks from the Phoronix Suite on several low cost development boards: $46* Banana Pi M2 based on Allwinner A31s quad core Cortex A7 processor @ 1.0 GHz with Armbian (Ubuntu 14.04) $74* Banana Pi M3 based on Allwinner A83T octa core Cortex A7 processor @ 1.80 GHz with Debian 8.3 $32 ODROID-C1+ based on Amlogic S805 quad core Cortex A5 processor @ 1.5 GHz with Ubuntu 14.04 $40 ODROID-C2 based on Amlogic S905 quad core Cortex A53 processor @ 2.0 GHz with Ubuntu 16.04 $74 ODROID-XU4 based on Samsung Exynos 5422 quad core ARM Cortex-A15 @ 2.0GHz quad core ARM Cortex-A7 @ 1.4GHz with Ubuntu 15.10 $10 Orange Pi One based Allwinner H3 Cortex A7 processor @ 1.2 GHz with Armbiam (Debian 8.3) $15 Orange Pi PC based on Allwinner H3 Cortex A7 processor @ 1.3 GHz with […]

March 22, 2016March 1, 2017 by Jean-Luc Aufranc (CNXSoft) - 36 Comments

NanoPi M1 Allwinner H3 Development Board with HDMI, CVBS, Ethernet and 3 USB Ports Sells for $11 (Sort of)

FriendlyARM has been very busy since the beginning of the year, as they’ve already released NanoPi 2 Fire, NanoPC-T2, and NanoPi-M2 boards, all based on Samsung S5P4418 processor so far in 2016. But they’ve not stopped, as the company has now launched NanoPi M1 board powered by Allwinner H3 processor with a similar form factor as NanoPi-M2, similar features as Orange Pi One, except they added two extra USB ports, an AV port with composite video and stereo audio, an on-board microphone, and an IR receiver. NanoPi-M2 board specifications (highlights show improvements or differences over Orange Pi One): SoC – Allwinner H3 quad core Cortex A7 @ 1.2 GHz with an ARM Mali-400MP2 GPU up to 600 MHz System Memory – 512 MB DDR3 (1GB as option) Storage – micro SD card slot Video & Audio Output – HDMI and 3.5mm jack for CVBS (composite + stereo audio) Connectivity -10/100M […]

March 16, 2016March 16, 2016 by Jean-Luc Aufranc (CNXSoft) - 19 Comments

Accelerated 3D Graphics, Hardware Video Decoding, and Network Performance on Orange Pi One Board (Video)

I’ve just written Getting Started Guide for Orange Pi One, a $10 development board based on Allwinner H3 quad core Cortex A7 processor, where I explain how to install and configure Armbian distribution on the board. As promised, I’ve also tested 3D graphics acceleration, and hardware video decoding, and also included some Ethernet benchmarks. Since ARM Mali-400 GPU found in Allwinner H3 is only capable of OpenGL ES, as in most ARM SoCs, you can test 3D graphics acceleration by using es2gears (and not glxgears as I’ve seen some other do in the past):

es2gears
EGL_VERSION = 1.4 Linux-r3p0-04rel0
vertex shader info:
fragment shader info:
info:
1463 frames in 5.0 seconds = 292.425 FPS

es2gears

EGL_VERSION = 1.4 Linux-r3p0-04rel0

vertex shader info:

fragment shader info:

info:

1463 frames in 5.0 seconds = 292.425 FPS

The log shows the utility is using Linux-r3p0 Mali driver, and the gears are display at a high frame rate close to 300 fps. If I switch to full screen, the frame rate drops to about 43 fps, which should still be acceptable. CedarX is the infamous closed source and GPL violating media library released […]

March 16, 2016May 5, 2016 by Jean-Luc Aufranc (CNXSoft) - 34 Comments

Orange Pi One Board Quick Start Guide with Armbian Debian based Linux Distribution

Orange Pi One board is the most cost-effective development board available on the market today, so I decided to purchase one sample on Aliexpress to try out the firmware, which has not always been perfect simply because Shenzhen Xunlong focuses on hardware design and manufacturing, and spends little time on software development to keep costs low, so the latter mostly relies on the community. Recently, armbian has become popular operating systems for Linux ARM platform in recent months, so I’ve decided to write a getting started guide for Orange Pi One using a Debian Desktop image released by armbian community. Orange Pi One Unboxing But let’s start by checking out what I received. The Orange Pi One board is kept in an anti-static bag, and comes with a Regulatory Compliance and Safety Information sheet, but no guide, as instead the company simply asks users to visit www.orangepi.org to access information […]

March 10, 2016March 10, 2016 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

BeagleBone Enhanced Adds Gigabit Ethernet, More Memory & USB Ports, and Sensors (Crowdfunding)

It’s nice to see BeagleBone Black‘s open source hardware being leveraged by third parties, as we’ve already seen designs such as BeagleBone Green and BeagleBone Black Industrial 4G in the past, and now UK based SanCloud has decided to launch BeagleBone Enhanced on Indiegogo (flexible funding). BeagleBone Enhanced board specifications with bold highlights showing improvements over the BeagleBone Black Rev. C: SoC – Texas Instruments Sitara AM3358 Cortex A8 @ 1 GHz + PowerVR SGX530 GPU System Memory – 1GB DDR3 RAM @ 800 MHz Storage – 4GB eMMC flash + micro SD slot, optional 1MB SPI NOR flash USB – 2x USB 2.0 host port (A type), mini USB OTG port, 2x USB interfaces via expansion header Serial Port – UART0 via 3.3V TTL header Ethernet – Gigabit Ethernet Video Output – micro HDMI with EDID support, up to 1280×1024 resolution. Audio Output – Via HDMI Sensors Optional 6 […]

March 7, 2016March 7, 2016 by Jean-Luc Aufranc (CNXSoft) - 18 Comments

LeMaker Cello 96Boards EE Board Powered by AMD Opteron A1120 Processor Targets Server Applications

There are two versions of Linaro’s 96Boards specifications the Consumer Edition (CE) and the Enterprise Edition (EE) with higher hardware requirements, and while several boards mostly compliant with 96Boards CE are available such as DragonBoard 410c and Hikey boards, the only board announced to be compliant with 96Boards EE specifications was AMD Huskyboard based on Opteron A1100 series processor and is yet to be available for sale. LeMaker has now designed a similar EE boards called Cello. LeMaker Cello board specifications: Processor – AMD Opteron A1120 quad core Cortex A57 processor @ 1.7 GHz with 2MB L2 cache, 8MB L3 cache System Memory – 2x DDR3 SO-DIMM sockets Storage – 2x SATA 3.0 ports, micro SD slot Connectivity – 1x Gigabit Ethernet RJ45 port USB – 2x USB 3.0 ports Expansions x16 PCIe G3 slot 40-pin Low Speed (LE) expansion header Debugging – micro USB port for console access, 10-pin […]