crowd supply News - Page 23 of 26 - CNX Software

May 7, 2018May 7, 2018 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

HiFive Unleashed RISC-V Linux Development Board Gets a $2000 FPGA Expansion Board

If you’re a RISC-V architecture’s enthusiast or represent a company working on products with the new ISA, you may have spent $999 or more on Hifive Unleashed RISC-V Linux development board a few months ago. You now have the opportunity to spend an extra $1,999 for HiFive Unleashed Expansion Board powered by a MicroSemi PolarFire FPGA programmed with a PCIe root port bridge, and allowing you to test all sorts of peripherals such as HDD’s & SSD’s, HDMI output, and audio cards, network adapters, graphics cards, and so on. Expansion board specifications: FPGA – Microsemi Low Power PolarFire FPGA with 300K Logic Element 4 Gbit DDR4 x16 SPI Flash for remote FPGA updates, QSPI Flash connected to GPIO 24 lane PCIe Switch x1 PCI Express card connector x16 PCI Express card connector with 4 lanes of PCIe gen2 connected SSD M.2 connector SATA connector HDMI connector eMMC Nand Flash uSD […]

May 2, 2018 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

XTRX SDR Mini PCIe Card Supports 10 MHz to 3.8 GHz Tuning Range, up to 120 MSPS Sample Rate

Fairwaves is a startup that aims to make deploying and operating mobile networks in rural regions profitable, and their latest project is called XTRX, a high performance Software Defined Radio (SDR) board packed into a mini PCIe card form factor. The project was launched on Crowdsupply earlier with year, got fully funded by around 700 backers, and the company is now working on fulfilling backers rewards by the end of August. XTRX board specifications: RF Chipset – Lime Microsystems LMS7002M FPRF (as found in LimeSDR Mini) FPGA Chipset – Xilinx Artix 7 35T RF Channels – 2 × 2 MIMO Sample Rate – ~0.2 MSPS to 120 MSPS SISO / 90 MSPS MIMO Tuning Range: 30 MHz – 3.8 GHz Rx/Tx Range: 10 MHz – 3.7 GHz 100 kHz – 3.8 GHz with signal level degradation PCIe Bandwidth PCIe x2 Gen 2.0 up to 8 Gbit/s PCIe x1 Gen 2.0 […]

April 9, 2018April 9, 2018 by Jean-Luc Aufranc (CNXSoft) - No Comments

TinyFPGA BX is a Tiny Open Source Hardware iCE40 FPGA Board that Fits into a Breadboard (Crowdfunding)

Last Friday, I wrote about Fipsy, a $10 breadboard-friendly FPGA board powered by Lattice Semi MachXO2 FPGA with 256 LUTs, but I then remember I had covered a board somewhat similar with TinyFPGA board last year based on either the same MachXO2-256 (TinyFPGA A1), or a slightly more powerful MachXO2-1200 FPGA (TinyFPGA A2). It happens the developer is now running a crowdfunding campaign on Crowdsupply for TinyFPGA BX board, which can be used with a breadboard, and is powered by Lattice Semi ICE40LP8K FPGA that will offer more flexibility thanks to 7,680 LUTs. TinyFPGA BX specifications: FPGA – Lattice Semi ICE40LP8K FPGA with 7,680 four-input look-up-tables, 128 KBit block RAM, Phase Locked Loop Storage – 8 MBit of SPI Flash Expansion 2x 14-pin header for I/Os, GND and Vin 21x solder pads on back of the board USB – 1x micro USB 2.0 FS port for programming Oscillator – 16 […]

February 4, 2018March 16, 2018 by Jean-Luc Aufranc (CNXSoft) - 19 Comments

SiFive Introduces HiFive Unleashed RISC-V Linux Development Board (Crowdfunding)

RISC-V free and open architecture has gained traction in the last couple of years. SiFive has been one of the most active companies with RISC-V architecture, introducing Freedom U500 and E500 open source RISC-V SoCs in the summer of 2016, before launching their own HiFive1 Arduino compatible board, and later the official Arduino Cinque board. That’s fine if you are happy with MCU class boards, but RISC-V is getting into more powerful processors, and recently got initial support o Linux 4.15, so it should come as no surprise the company has now launched HiFive Unleashed, the first RISC-V-based, Linux-capable development board. HiFive Unleashed key features and specifications: SoC – SiFive Freedom U540 with 4x U54 RV64GC application cores @ up to 1.5GHz with Sv39 virtual memory support, 1x E51 RV64IMAC Management Core, 2 MB L2 cache; 28 nm TSMC process System Memory – 8GB DDR4 with ECC Storage – 32MB […]

January 10, 2018January 10, 2018 by Jean-Luc Aufranc (CNXSoft) - No Comments

Tomu Arm Board Fits into a USB Connector, Adds Buttons, Two Factor Authentication to Your Computer (Crowdfunding)

We’ve covered many boards that claim to be the world’s smallest development board, and Tomu board does not claim anything like that, but it’s pretty small, as it’s made to fit into your computer’s USB board. It may be cool, but it could also potentially be useful, as the board exposes two (capacitive touch?) buttons, and two LEDs so you can use it as a computer accessory for example to add volume buttons, or as a Universal 2nd Factor (U2F) token supporting two-factor authentication (2FA) to login to compatible online services. Tomu board hardware specifications: MCU – Silicon Labs Happy Gecko EFM32HG309 ARM Cortex-M0+ up to 25 MHz with 64KB flash, 8KB RAM USB – 1x USB 2.0 FS port Misc – 2x buttons, 2x LEDs: 2 (red + green) Dimensions – 1.4mm thick (0.6mm thick PCB) Singapore based Sutajio Ko-usagi – the company behind the project – provides the […]

December 27, 2017December 27, 2017 by Jean-Luc Aufranc (CNXSoft) - No Comments

ALio Proto Board Supports Through Hole, DIP, and SMD Components (Crowdfunding)

Perfboards and stripboards are very useful to design your own simple electronic boards without having to design your own board from scratch. However, you have to select through hole or DIP components, as – while possible with some efforts – such boards are not designed for SMD components. AERD, an open source electronic development startup based in Indonesia, has designed ALio prototyping boards supporting both through hole and SMD components, as well as some common connectors/accessories such as micro SD card, USB connector, and so on. Three versions of the board (basic, embedded, Arduino) are available with the following specifications & features: Fits SMD and PTH components at the same time. Double layer bus (top and bottom) Other components/headers All versions – 1.1 mm pitch pad for micro SD/SD card breakout Embedded & Arduino only – mini & micro USB pads, 1x SPI breakout Arduino only – Arduino header, one […]

December 10, 2017 by Jean-Luc Aufranc (CNXSoft) - 15 Comments

Anavi Light pHAT Adds RGB Light Strip Support to Raspberry Pi Boards (Crowdfunding)

He works as a software engineer for his main job, but Leon ANAVI is apparently enjoying his hobby of designing open source hardware, as after RabbitMax Flex home automation HAT, and ANAVI Infrared pHAT with IR transmitter and receiver, he has come up with as third project: Anavi Light pHat, an add-on board for Raspberry Pi 3/Zero (W) that adds support for RGB light strips. Light pHAT specifications: Compatible with 40-pin Raspberry Pi header EEPROM with board manufacturer information and a device tree fragment Terminal block for a 12V RGB LED strip 3x 4-pin I2C headers for sensor modules 1x 3-pin header for PIR motion sensor 1x 4-pin UART header for debugging Dimensions – pHAT form factor You first need to connect the pHAT to your board, and then LED strip, and you can then control the lights using Home Assistant open source home automation platform, with the strip integrated […]

November 21, 2017 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Pi/104 Carrier Board for Raspberry Pi Compute Modules (Partially) Complies with PC/104 OneBank Specs (Crowdfunding)

The PC/104 consortium maintains various standards for embedded computer defining both the buses to use and form factors. PC/104 SBCs/boards are mainly used in rugged industrial computers, and stackable through ISA and PCIe buses. The standards were mostly designed for x86 processors, but in Q1 2015, the consortium added the OneBank option to PCI/104-Express & PCIe/104 Specification, Revision 3.0 in order to enable lower cost solutions and processors with PCIe and USB interfaces. This brought some lower powered Intel and ARM+FPGA based PC/104 compliant boards to the market such as Winsystems PX1-C415 based on Intel Apollo Lake E3900 SoC, or Sundance EMC²-Z7030 powered by Xilinx Zynq-7030 ARM+FPGA SoC. Adam Parker (Parker Microsystems) has decided to bring the PC/104 OneBank industrial standard to the Raspberry Pi world, by creating Pi/104 a carrier board for the RPi compute modules that (mostly) complies with PC/104 OneBank for factor, and exposes the required USB […]