compulab

Posted on by Jean-Luc Aufranc (CNXSoft) - 3 Comments on Fedora 20 “Heisenbug” Release Makes ARM a Primary Architecture

Fedora 20 “Heisenbug” Release Makes ARM a Primary Architecture

Fedora has been supporting ARM architecture for a while now, but it was only as a secondary architecture without official support. With the recent Fedora 20 release, nicknamed “Heisenbug”, the ARM architecture, more exactly ARMv7 hard float and greater, is promoted to a primary architecture meaning ARMv7 will have the same status as x86 and x86_64 architectures with packages officially build and supported by the Fedora community. What it does not mean however, due to the nature of ARM architecture, is that you can simply download an ISO to install on any ARM platforms, like you would do on an Intel or AMD computer. It’s a little more complicated than that, as it is platform specific, but instructions are available for the Beaglebone Black, Compulab Trimslice, the Wandboard, Calxeda Energycore Midway and Highbank, and Versatile Express in QEMU. You can download images with MATE, KDE, XFCE, LXDE, SOAS desktops, as […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 18 Comments on $99 (and up) Compulab Utilite ARM based Computer Runs Ubuntu or Android

$99 (and up) Compulab Utilite ARM based Computer Runs Ubuntu or Android

If you’re ready to tinker it’s possible to run Linux in one of the low cost ARM based set-top boxes or mini PCs currently available, although if you need Linux with 3D acceleration and video playback, your only realistic option is to go with solutions based on Freescale i.MX6. Compulab has been developing a mini desktop computer based on Freescale i.MX6 Solo, Dual or Quad that will run either Ubuntu or Android, so you don’t need to mess around to run Ubuntu on cheap ARM hardware. The device is expected to sell for $99 and up starting in August according to Fanlesstech. Compulab Utilite will have the following specifications: SoC – Freescale i.MX6 single / dual / quad core Cortex-A9 up to 1.2GHz, with Vivante GPU, and Video Processing Unit supporting multi-stream 1080p H.264, VC1, RV10, DivX HW decoding System Memory – Up to 4GB DDR3-1066 Storage – 1MB SPI […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Compulab CM-T335 CoM with TI Sitara AM335x Sells for $27

Compulab CM-T335 CoM with TI Sitara AM335x Sells for $27

Compulab, an Israeli company specialized in embedded computing, has just released CM-T335, a family of low cost computer-on-module powered by Texas Instruments Sitara AM335x SoC, and sells for as low as $27 per unit for the AM3352 version (no GPU) for 1k orders. The module is available in commercial, extended and industrial grades, and features up to 512 MB RAM, and 1 GB Flash. Specifications: SoC –  Texas Instruments AM3352 CPU @ 275MHz, or AM3354 @ 600MHz + PowerVR SGX530 GPU System Memory – 128MB to 512MB DDR3-1066, 16-bit bus width Storage – 128MB to 1GB on-board NAND flash, 8bit, SLC Display – 24-bit Parallel display interface – up to 1366 x 768 Touchscreen – 4/5/8-wire resistive touch-screen support, capacitive touch-screen support through SPI interface Connectivity: Ethernet – 1000Base-T Ethernet interface implemented with AM335x integrated MAC and the Atheros AR8033 RGMII PHY WiFi – 802.11b/g/n implemented with TI WL1271 chipset […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 5 Comments on $89 Compulab CM-iGT CoMs Feature AMD G-Series APUs

$89 Compulab CM-iGT CoMs Feature AMD G-Series APUs

Compulab, an Israeli company specialized in embedded computing, has recently introduced computers-on-module based on AMD G-Series APUs that will sell for as low as $89 per unit (for 1k orders) depending on selected features and options. The module is available in commercial, extended and industrial grades, and supports up to 4GB RAM, and 32 GB Flash. Here are the specifications of these modules: CPU  – AMD G-Series Processor: G-T16R single-core @ 600MHz, G-T40E dual-core @ 1GHz or G-T56N dual-core @ 1.65GHz GPU – Integrated GPU Radeon HD 6250 supporting the following standards: DirectX 11, OpenGL 4.0, OpenCL Video Processing Unit – UVD 3 engine with native H.264, VC-1, MPEG2, and DivX, 1080p Blu-Ray playback support System Memory –  2GB – 4GB DDR3-1066, 64-bit Storage: On-board BIOS flash, 1MB, reprogrammable On-board SSD, up to 32GB, MLC, through SATA interface Interfaces: Display – Up to two DisplayPort interfaces, up to two HDMI […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on AMD Embedded G-Series mini-PC, motherboard and thin client

AMD Embedded G-Series mini-PC, motherboard and thin client

AMD announced its embedded processor G-Series at CES 2011. Here are some products that will be soon available based on this platform. Futjisu Mini-ITX mainboards – models D3003-S1 and D3003-S2 The D3003-S1 motherboard will feature an AMD Single-Core T44R (1.2GHz/9W) and the D3003-S2 an AMD Dual-Core T56N (1.6GHz/18W). Both models will have an onboard ATI graphics card with VGA, DVI, LVDS (D3003-S1 only) and diplayport  (D3003-S2 only) outputs, HD Audio,  dual GbE LAN, serial ATA III RAID, mSATA socket support, USB 2.0, 8 Bit GPIO connector and be designed for fanless operation. Mass production of the boards will start in April 2011. Check the preliminary specifications for details. CompuLab’s fit-PC3 mini-PC Compulab already manufactures the fit-PC2 and fit-PC2i based on the Intel Atom platforms running Linux, Windows XP and Windows 7. The Israel-based company  will embed AMD Embedded G-Series processor in its latest fit-PC3 mini-PC. This “miniature fanless industrial PC” […]

Exit mobile version
EmbeddedTS embedded systems design