camera News - Page 22 of 65 - CNX Software

June 21, 2022February 10, 2023 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Ingenic T31-based WiFi AI camera development kit promises over a year of battery life

Ingenic T31 AI camera devkit one-year battery life

We’ve previously seen WiFi security cameras promising a year of battery life with products like the Eufy EverCam, but the Ingenic T31-based Smart Video Application Development Kit by Innophase may allow for the development of even more power-efficient WiFi AI security cameras with AI processing last can last over one year. The development kit combines Ingenic T31 MIPS & RISC-V camera SoC with Innophase Talaria TWO INP101x ultra-low-power (57µA @ DTIM10) Wi-Fi & BLE wireless module, that is estimated to last 14.4 months on a 3,000 mAh battery while operating at a 99.3% idle, 0.7% video capture ratio. Development kit content: Board with Ingenic T31 MIPS processor @ 1.5 GHz and RISC-V low-power core, H.265 encoder, 512Mbit or 1Gbit on-chip memory fitted with 2M pixel Full-HD camera @ 30fps USB Debug board Microphone and speaker InnoPhase Talaria TWO SDIO Adapter Board Fitted with INP1014 LGA module with 2.4GHz WiFi 4, […]

June 14, 2022June 18, 2022 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Open-source hardware USB Type-C industrial camera features Lattice Crosslink NX FPGA

Gaurav Singh, acting as Circuit Valley, has designed an open-source hardware USB 3.0 Type-C industrial camera with three boards: one to capture data through a CMOS sensor, another based on a Lattice Crosslink NX FPGA to handle image processing, and finally, a board equipped with an Infineon FX3 USB 3.0 controller for sending the video data to the host. This design allows the DIY camera to be extremely flexible, as for instance, you could keep the FPGA and USB board, and simply change the sensor board for a better/different camera. A 3D printable enclosure is also provided, and the camera supports C-mount lenses, so the lens can also be easily changed as required. Here’s what the final result looks like. Camera specifications: Sensor board Sensor for example Sony IMX290, IMX327, or IMX462 Oscillator FPGA/Host board interface – High-density connector with I2C, 4-lane MIPI with clock, I2C, a few other control […]

May 31, 2022May 31, 2022 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

4K USB AI camera is powered by Rockchip RV1126 SoC with 2.0 TOPS NPU

ThinkCore TC-RV1126 is a USB AI camera powered by Rockchip RV1126 quad-core Cortex-A7 processor with a 2.0 TOPS NPU and equipped with a Sony Starvis IMX415 CMOS image sensor with 4K resolution (3840 x 2160). The Linux-powered camera module features a USB Type-C port compatible with UVC & UAC protocols so that it can work without drivers on Windows, Android, Linux, Mac OS, and most other operating systems with a USB stack. TC-RV1126 camera specifications: SoC – Rockchip RV1126 quad-core Arm Cortex-A7 @ 1.5 GHz + RISC-V MCU @ 400 MHz, 2D graphics engine, 2.0 TOPS NPU with support for INT8/ INT16, 14M ISP System Memory – 2x DDR3 chip (128M x 16), so that should be 512MB RAM (TBC) Storage – 1 Gbit (128MB) SPI NAND flash Camera Image sensor – Sony Starvis IMX415 1/2.8-inch 8MP CMOS sensor with night vision Capture up to 3840×2160 @ 30 fps Supported […]

May 27, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

DepthVista USB 3D ToF camera supports close range depth measurement, far-range object detection

DepthVista is a USB Time-of-Flight (ToF) camera designed for precise 3D depth measurement in close range mode (1.2m) and person and/or object detection in far-range mode up to 6 meters away. This ToF camera combines a 3D depth camera capable of 640 x 480 @ 30fps, and an Onsemi AR0234 color global shutter sensor supporting HD and FHD at up to 30fps, plus an 850nm VCSEL (vertical-cavity surface-emitting laser) for safety and the ability to operate in complete darkness. e-con Systems’ DepthVista (See3CAM_TOF_25CUG) specifications: Depth camera 3D camera technology: Time-of-Flight Depth range Near mode – 0.2m to 1.2m Far mode – 1m to 6m Illumination: 850nm pulsed laser (Indoor) Accuracy: Up to 1% depending on environmental conditions Output format: Y16 (raw 12-bit) Resolutions Depth – 640 x 480 @ 30fps IR – 640 x 480 @ 30fps Depth + IR – 640 x 960 @ 30fps FOV – 84.29° (H) […]

May 25, 2022May 25, 2022 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Microchip SAMA7G54 is a single-core Arm Cortex-A7 microprocessor for low power AI camera & audio applications

Microchip has just announced the 1 GHz SAMA7G54 single-core Arm Cortex-A7 microprocessor (MPU) with MIPI CSI-2 and parallel camera interfaces, as well as up to four I2S, one SPDIF transmitter and receiver, and a 4-stereo channel audio sample rate converter. The company specifically launched a single-core processor to offer a lower power solution for AI camera and audio solutions, and the chip is coupled with the MCP16502 power management IC that has been optimized to provide the best power/performance ratio for the SAMA7G54. Microchip SAMA7G54 specifications: CPU – Arm Cortex-A7 based MPU @ up to 1GHz with 256KB L2 cache Memory – DDR2/DDR3/DDR3L/LPDDR2/LPDDR3 up to 533MHz Storage – Quad SPI, Octal SPI, 3x SD/eMMC Camera I/F – MIPI CSI-2 (2-lane up to 1.5 Gbps each) and 12-bit parallel camera Up to 8 Mpixel @ 30 fps Audio – Up to 4x I2S, PDM, SPDIF (Rx/Tx), 4 stereo channel ASRC Networking […]

May 3, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

Axiomtek AIE900-XNX – A 5G connected fanless Edge AI system for AMR, AGV, and computer vision

Axiomtek AIE900-XNX is a fanless Edge AI computing system powered by NVIDIA Jetson Xavier NX system-on-module designed for autonomous mobile robots (AMR), automated guided vehicles (AGV), and other computer vision applications. The system delivers up to 21 TOPS thanks to the 6-core NVIDIA Carmel ARM v8.2 (64-bit) processor, NVDLA accelerators, and 384-core NVIDIA Volta architecture GPU found in the Jetson Xavier NX module. The AIE900-XNX Edge AI computer also comes with a 5G module for high-speed cellular connectivity and supports SerDes, PoE, and MIPI CSI cameras for video processing. Axiomtek AIE900-XNX specifications: NVIDIA Jetson Xavier NX system-on-module with CPU – 6-core NVIDIA Carmel Armv8.2 64-bit CPU with 6 MB L2 + 4 MB L3 cache GPU – 384-core NVIDIA Volta GPU with 48 Tensor Cores AI Accelerator – 2x NVDLA System Memory – 8GB 128-bit LPDDR4x onboard Storage – 16GB eMMC flash Storage – M.2 Key M 2280 with PCIe […]

April 28, 2022June 22, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

Orbbec Persee+ 3D AI camera runs Ubuntu or Android on Amlogic A311D processor

Orbbec Persee+ is a 3D depth camera running Linux with AI capabilities thanks to Amlogic A311D hexa-core processor equipped with a 5 TOPS NPU (Neural-network Processing Unit). The Persee+ is designed to help researchers, engineers, and hobbyists implement advanced uses for 3D imaging. Orbbec has been around for several years with the first product we covered here being the Orbbec Persee 3D depth camera running Ubuntu or Android on Rockchip RK3288 processor and unveiled in 2015. Last year, the company introduced the Zora P1 Amlogic A311D development board for Orbbec 3D cameras, so in a way, the Orbbec Persee+ is born from the work done on the Persee camera and Zora P1 over the years. Orbbec Persee+ 3D AI camera specifications: SoC – Amlogic A311D hexa-core processor with 4x Cortex-A73 cores, 2x Cortex-A53 cores, Arm Mali-G52MP4 GPU, 5 TOPS NPU System Memory – 4GB RAM Storage – 8GB (specs) / […]

April 27, 2022April 27, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

Axzez Interceptor carrier board for RPi CM4 gets 8-port PoE+ board

The features-rich Axzez Interceptor carrier board for Raspberry Pi CM4 has gotten the Interceptor PoE board with eight PoE+ ports for connecting up to sixteen PoE IP cameras making it usable as a network video recorder. We first wrote about the Interceptor last January noting its impressive I/O capabilities with five SATA ports, four Gigabit Ethernet, two HDMI ports, RS-485 terminal block, and more. It also had two 40-pin FFC connectors “for future expansion”. Those connectors have now found a “meaning to life” with the Interceptor PoE board, as up to two can be connected to the FFC connectors. Some of the features of the new Interceptor PoE Board include: 8x fast PoE+ ethernet ports IEEE 802.3AF-2003 and 802.3AT-2009 compliance Each port has activity/link and status LEDs Input voltage range – 44-57V Optional 48V power boost that can support up to two Interceptor PoE+ boards (Powered from 12V ATX power […]