bluetooth News - Page 27 of 72 - CNX Software

July 15, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Qualcomm QCM2290/QCS2290 SoM and Devkit target Industrial IoT applications

Last June, Qualcomm introduced several industrial IoT solutions that we did not cover at the time with Qualcomm QCM2290/QCS2290 IoT chip for camera applications, industrial handhelds, retail and tracking, Qualcomm QCS8250 WiFI 6 & 5G SoC for connected healthcare, digital signage, retail, and video collaboration, Qualcomm QCS6490/QCM6490 WiFI 6E & 5G SoC for connected healthcare, logistics management, retail, transportation, and warehousing, and Qualcomm QCS4290/ QCM4290 designed for cameras, industrial handhelds, and security panels with 4G LTE and WiFi 6 connectivity. Shortly after Qualcomm’s announcement, Thundercomm introduced the TurboX C2290/CM2290 system-on-module respectively based on Qualcomm’s quad-core Cortex-A53 QCS2290 SoC and QCM2290 SoC adding 4G connectivity. The module also offers WiF & Bluetooth, as well as MIPI display & camera interfaces, and the TurboX CM2290/C2290 development kit is also available to get started. TurboX CM2290 and C2290 SoM Specifications: SoC – Qualcomm Snapdragon QCM2290 or QCS2290 quad-core Cortex-A53 processor at up to […]

July 8, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

u-blox introduces WiFI 5/6 & Bluetooth 5 M.2 cards

u-blox is well known for its wireless modules be it WiFi, Bluetooth, GPS, or cellular connectivity that are soldered unto CPU modules or boards. But the company has now introduced two M.2 cards with WiFi 5 or WiFi 6 and Bluetooth 5.x that work with NXP i.MX evaluation and development boards. M2-JODY-W2 M.2 card The M2-JODY-W2 card comes with the following features: Connectivity Wi-Fi 5 1×1 SISO IEEE 802.11ac data rates up to 433 Mbit/s (PHY, MCS9), beamforming Supports 802.11d/e/h (DFS)/i/k/r/u/v/w/ai Wi-Fi 20, 40, and 80 MHz channels Bluetooth BR/EDR and Bluetooth low energy v5.0 supporting 2 Mbit/s Access point mode for up to 8 stations 2x u.FL antenna connectors Host interfaces SDIO & UART host interfaces PCM interface for Bluetooth audio Security Hardware encryption engines: AES and TKIP WPA, WAPI, WPA2, WPA3, WPS, and Easy Connect Dimensions – M.2 Type 2230 Key E form factor Certifications – Chipset is […]

June 22, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Posture correction smart sensor helps you sit or stand upright

It’s easy to adopt a bad posture either while sitting in front of a computer or while walking and your mobile, and over time this may lead to unaesthetic and/or painful postural disorders. To solve this issue, a posture correction smart sensor may be used in place of a posture belt with what looks like a GPS tracker placed on the back of the patient, and which notifies bad postures by vibrating and to your smartphone depending on a user-configured angle range. Specifications listed for the posture-correction-smart-sensor: Sensor – Unnamed Bosch gravity sensor Connectivity – Bluetooth 4.2 Misc Medical-grade gel patch to attach the device to the bag Vibration motor Battery – 200mAh; 30 minutes charge good for about 5 days when using it for about 8 hours per day Dimensions – 6 x 4 x 1.2 cm Weight – 16 grams. The device ships with a micro USB cable […]

June 19, 2021 by Saumitra Jagdale - 2 Comments

Digi ConnectCore 8M Mini SOM and Mini Development Kit for Industrial IoT Applications

Digi International has announced the Digi ConnectCore 8M Mini System-on-Module (SOM) which is an addition to its ConnectCore family modules. We saw the Android application development kit featuring earlier Digi Wireless modules based Freescale i.MX51 (ConnectCore Wi-i.MX51) and i.MX53 (ConnectCore Wi-i.MX53) in early 2012. The new Digi ConnectCore 8M Mini comes with a built-in Video Processing Unit specialising in vision use cases. The Digi ConnectCore 8M Mini SOM is an industrial i.MX 8M Mini quad-core system-on-module that comes with Arm Cortex-A53 cores, one Cortex-M4 core, and the Cortex-M0-based Digi Microcontroller Assist. This enables optimal power consumption while simultaneous maintenance of highly efficient performance. Main benefits of Digi Connect Core 8M Mini SOM Digi SMTplus form factor (40 x 45 mm) for flexibility and reliability while designing. Power management with both hardware and software support for low-power designs. Display and camera capabilities with graphics and video hardware acceleration make it suitable […]

May 4, 2021May 4, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Ebyte E104-BT11 Bluetooth Mesh module features Silicon Labs EFR32MG21 MCU

Ebyte E104-BT11 is a Bluetooth Mesh module offered in four variants with support for gateways (G) and node (N) versions, as well as PCB or IPEX antenna versions. Interestingly it is based on Silicon Labs EFR32MG21 Cortex-M33 microcontroller also found in ITEAD Zigbee 3.0 USB dongle, so it’s not impossible that it could be repurposed for Zigbee or Thread with firmware from Silabs. Ebyte E104-BT11 module specifications: Wireless MCU – Silicon Labs EFR32MG21 Arm Cortex-M33 microcontroller @ up to 80 MHz with DSP and FPU, up to 1024 kB flash, up to 96 kB RAM, 2.4 GHz IEEE 802.15.4 for Bluetooth LE, Zigbee, or Thread Wireless connectivity Bluetooth Mesh/BLE support with default firmware, up to 10,922 devices supported Max Tx power – 20 dBm Rx sensitivity- -88 to -97 dBm (-97 dBm typ.) Max data rate – 1Mbps Antenna – PCB antenna up to 200-meter range, or IPX antenna up […]

April 22, 2021April 22, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

InfiniTime 1.0 firmware released for PineTime smartwatch

The PineTime smartwatch was unveiled and first launched in 2019, as a low-cost, open-source wearables development kit/platform for developers wanting to work on firmware development for the Nordic nRF52 powered device. Progress was made on various solutions such as ATCwatch Arduino firmware, and as time passed, the PineTime slowly became more like an “enthusiast-grade” end-user product. This is basically what it has become with the first stable release of InfiniTime firmware, which was selected as the default firmware in September 2020. The main features of InfiniTime 1.0 firmware include: Two clock faces – digital and analog Apps – Stopwatch, music control, navigation, heart rate, as well as Paddle and 2048 games User settings – Display timeout, time format, wake up conditions OTA upgrades via an open-source bootloader based on MCUBoot Heart rate monitoring and step counting Between 3 and 5 days of battery life depending on usage Firmware based on […]

March 30, 2021March 30, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Renesas RE01B Bluetooth 5.0 LE MCU harvests energy for battery maintenance-free IoT devices

EB-RE01B Bluetooth-5.0-Energy Harvesting Board

Nobody likes to change or recharge batteries in their IoT nodes, so any new development related to energy harvesting or batteryless devices is welcomed. Renesas RE01B is a new Bluetooth 5.0 Low Energy (BLE) Arm Cortex-M0+ MCU that consumes at little as 35 µA/MHz during operation and 600 nA during standby making it suitable for battery maintenance-free IoT devices, or even batteryless IoT devices thanks to its energy harvesting controller. Renesas RE01B microcontroller’s features and specifications: CPU – Arm Cortex-M0+ core up to 64MHz GPU – 2D graphics accelerator Memory – 256KB SRAM Storage – 1.5MB flash Connectivity – 2.4 GHz radio with Bluetooth 5.0 Low Energy; up to 400m range (Long Range) and 2 Mbps data rate I/Os 8x PWM outputs 7x 14-bit A/D converters (ADC, Analog inputs) SCI (UART), I2C, SPI Timers 1x 32-bit Timer, 3x 16-bit Timer, 2x 8-bit Timer 2x Watchdog Timer, 1-second event timer, stopwatch […]

March 21, 2021March 21, 2021 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Arduino WiFi & Bluetooth watch adds GPS, MicroSD slot, loses audio amplifier

LilyGO introduced the ESP32 powered T-Watch-2020 smartwatch last year with a slim form factor, a 1.54-inch LCD capacitive touch screen, WiFi & Bluetooth connectivity, and support for Arduino. In February, we noted TTGO T-Watch-2020 V3 with a built-in microphone to enable voice control, but the company has just listed TTGO T-Watch-2020 V2 adding GPS and a MicroSD card slot on its Aliexpress store for around $33. TTGO T-Watch-2020 V2 specifications: SoC – Espressif ESP32 dual-core wireless processor with 520KB SRAM System Memory – 8MB PSRAM Storage – 16MB QSPI flash, MicroSD card slot Display – 1.54-inch LCD capacitive touch screen Audio – Max98357 Class-D amplifier, buzzer/speaker Connectivity 802.11b/g/n WiFi 4 and Bluetooth 4.x/5.1 via ESP32 Quectel L76L module for GNSS (GPS, Beidou,GLONASS, QZSS) Sensors – BMA423 three-axis accelerometer with built-in step counting algorithm, activity recognition/tracking, advanced gesture recognition. Expansion – 13-pin 0.3mm pitch FPC expansion socket (shared with MicroSD card […]