automotive News - Page 10 of 33 - CNX Software

August 24, 2022August 25, 2022 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

WiCAN ESP32-C3 CAN Bus platform is available in USB-CAN and OBD-II form factors (Crowdfunding)

WiCAN is an ESP32-C3 CAN bus adapter that works over USB, Wi-Fi, and Bluetooth LE, and designed for car hacking and general CAN bus development. The device is available in USB-CAN and OBD-II form factors and comes with firmware that works with RealDash to create nice-looking dashboards with the data. RealDash can be installed on Android, iOS, and Windows 10 operating systems. WiCAN specifications: Wireless module – ESP32-C3-MINI-1 with ESP32-C3 RISC-V microcontroller with 2.4GHz WiFI 4 and Bluetooth 5.0 connectivity, 4 MB flash, PCB antenna CAN 2.0 A/B interface up to 1 Mbps Host interface WiCAN-OBD – OBD-II connector WiCAN-USB – Mini USB port for USB-to-UART up to 6 Mbps Power Supply WiCAN-ODB – 7.5V to 16V (Vbat) WiCAN-USB – 7.5V to 36V via screw-terminal connector Power Consumption – <= 1 mA in battery-saving mode The CAN Bus adapter also supports firmware updates over WiFi, and can be used either […]

July 25, 2022July 25, 2022 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

EM PRO mini – An AMD Ryzen Embedded R1102G fanless mini PC

E.E.P.D. EM PRO mini “eNUC-BoxPC” is a mini PC powered by a 6-watt AMD Ryzen Embedded R1102G dual-core processor and designed for a variety of applications such as thin client, network monitoring, production data acquisition, digital signage, point-of-sale, building management systems, and so on. The embedded fanless mini PC ships with up to 16 GB DDR4 RAM, supports M.2 SATA or NVMe storage, and offers two mini DisplayPort video outputs, three USB 3.1 ports, and two Gigabit Ethernet ports, as well as serial ports. The mini PC offers 8V to 32V input voltage suitable for automotive applications and can operate in the 0°C to 50°C temperature range, although a wider range can be worked on upon request. EM PRO mini specifications: SoC – AMD Ryzen Embedded R1102G dual-core processor @ 1.2 GHz / 2.6 GHz (Turbo) with 3CU Radeon Vega 3 graphics @ 1.0 GHz; TDP: 6W System Memory – […]

July 16, 2022July 23, 2022 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

CANDuino v3 – A Microchip ATmega168PA board with CAN bus, Arduino Nano form factor

CANduino v3 is the third revision of MassiveButDynamic’s CAN bus board with Arduino Nano form factor based on Microchip ATmega168PA 8-bit AVR microcontroller, Microchip MCP2515 CAN controller with an SPI interface, and Microchip MCP2551 CAN transceiver suitable for 12V and 24V systems. The CANDuino v3 board is now slightly narrower in order to give access to two rows on each side when installed on a breadboard, comes with a USB Type-C port to reduce the number of cables needed, and the CAN bus function can be deactivated via a jumper in order to use the CANduino as a normal Arduino Nano. CANDuino v3 specifications: MCU – Microchip ATmega168PA 8-bit AVR microcontroller @ up to 16 MHz with 16KB flash, 512 bytes EEPROM, 1 KB SRAM CAN Bus CAN L/H header and CAN bus termination Microchip MCP2515 CAN controller connected to the AVR microcontroller over SPI. Supports CAN V2.0B at 1 […]

July 14, 2022July 14, 2022 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

can2040 project adds software CAN bus to Raspberry Pi RP2040 microcontroller

Raspberry Pi RP2040 can2040 software CAN Bus

The can2040 project is a software CAN bus implementation for the Raspberry Pi RP2040 microcontroller that leverages programmable I/Os (PIO) to achieve reading and writing CAN 2.0B data frames at rates up to 1Mbit per second. Kevin O’Connor, the developer of the project, further explains the implementation uses only one of the two RP2040 PIO hardware blocks, so it is possible for a single Raspberry Pi RP2040 chip to have two separate CAN bus interfaces. Some processing also happens on one of the Arm Cortex-M0+ cores of the microcontroller with the processing time dependent on the amount of bus traffic, and a fully saturated CAN bus at the fastest supported rate of 1Mbit/s may use up to around 30% of that core when clocked at 125MHz, so that should still leave plenty of room for other tasks that may run on the system. I could not find any information about […]

July 7, 2022July 7, 2022 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

CANBed M4 SAM E51 development board features MCP2542FD CAN transceiver

CANBed M4 development board based on Microchip SAM E51 Cortex-M4 microcontroller and MCP2542FD CAN transceiver provides a more powerful alternative to the CANBed RP2040 with a Raspberry Pi dual-core Cortex-M0+ microcontroller introduced last year. The board supports both CAN 2.0 and CAN FD with a 4-pin terminal block or a DB-9 connector, and offers expansion capabilities though two Grove connectors, and an 18-pin IO header. CANBed M4 specifications: MCU – Microchip ATSAME51G19A Arm Cortex M4 core @ up to 120 MHz with 512KB flash, 192KB RAM CAN Microchip MCP2542FD CAN transceiver with support for CAN 2.0 and CAN FD up to 2+ Mbps Input interface – DB-9 connector or terminal block 120 Ohm terminal resistor USB – 1x Micro USB port for programming Expansion I2C Grove connector UART Grove connector SPI header 18-pin I/O header with up to 12x GPIOs, UART, I2C, 4x analog inputs, 5V, and GND Misc – […]

July 1, 2022 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

AEC-Q100 qualified module features Allwinner T507-H processor for automotive applications

We first wrote about Allwinner T507 when we covered a module and devkit from Forlinx, but now MYiR Tech has designed its own AEC-Q100 qualified system-on-module (MYC-YT507H) and the MYD-YT507H development board based Allwinner T507-H processor. MYC-YT507H – Allwinner T507-H SoM Specifications: SoC – Allwinner T507-H with a quad-core Arm Cortex-A53 processor @ 1.5GHz, Arm Mali-G31 MP2 GPU with support for OpenGL ES 3.2/2.0/1.0, Vulkan1.1, OpenCL 2.0; 4K60 H.265/VP9/AVS2 video decoder, 4K H.264/MJPEG video encoder System Memory – 1 or 2GB LPDDR4 Storage – 8GB eMMC flash, 32Kbit EEPROM (or is it 32KB/256Kbit – see block diagram below) 222x castellated holes with 1.0mm pitch for carrier board connection Networking – 1x RGMII and 1x RMII Video 1x HDMI 2.0a up to 4Kp60 2x single-channel LVDS or 1x dual-channel LVDS or 24-bit RGB up to 1080p60 1x TV CVBS output with PAL/NTSC Camera – 1x DVP digital camera, 1x MIPI CSI […]

May 16, 2022August 9, 2022 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Embedded World 2022 – June 21-23 – Virtual Schedule

Embedded World 2020 was a lonely affair with many companies canceling attendance due to COVID-19, and Embedded World 2021 took place online only. But Embedded World is back to Nuremberg, Germany in 2022 albeit with the event moved from the traditional month of February to June 21-23. Embedded systems companies and those that service them will showcase their latest solution at their respective booths, and there will be a conference with talks and classes during the three-day event. The programme is up, so I made my own little Embedded World 2022 virtual schedule as there may be a few things to learn, even though I won’t be attending. Tuesday, June 21, 2022 10:00 – 13:00 – Rust, a Safe Language for Low-level Programming Rust is a relatively new language in the area of systems and low-level programming. Its main goals are performance, correctness, safety, and productivity. While still ~70% of […]

May 13, 2022May 13, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Allwinner T507 industrial processor powers automotive single board computer and module

Forlinx OKT507-C single board computer for automotive applications is powered by FETT507-C system-in-module equipped with Allwinner T507 industrial processor, 2GB RAM, and 8GB eMMC flash. Allwinner T507 offers the same features as Allwinner H616 for TV boxes with a quad-core Cortex-A53 CPU, a Mali G31 MP2 GPU, and the same I/Os, but the processor is AEC-Q100 certified, supports -40°C to +85°C temperature range, and Allwinner promises over 10 years of longevity. OKT507-C single board computer specifications: FETT507-C System on Module SoC – Allwinner T507 quad-core Cortex-A53 @ 1.5GHz with Arm Mali-G31 MP2 GPU with support for OpenGL ES 3.2/2.0/1.0, Vulkan1.1, OpenCL 2.0; (“2.25W power consumption under load”) System Memory – 2GB DDR3L Storage – 8GB eMMC flash Board-to-board connectors for carrier board connection Supply Voltage- 5 V Dimensions – 70 x 40 mm Temperature Range – -40°C to +85°C Carrier board Storage – MicroSD card slot Display I/F 1x LCD […]