automation News - Page 34 of 60 - CNX Software

November 8, 2019 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Tuya helps you easily Design & Manufacture your own Smart Home Solutions

I was recently informed about LSC Smart Connect 3 door sensor selling on Action discounter with over 600 stores across the Netherlands, Belgium, France, Germany, Luxembourg, Austria, and Poland. The door sensor is based on ESP8266, and people have bought a few and flashed their own open source firmware converting the device into a multi-purpose sensor device with ESPNOW protocol that enables direct and low-power control of Espressif devices without the need of a router. The module inside the door sensor is called TYWE3S, which one document on the FCC website refers to as “Tuya WiFi module” and further mentions “TYWE3S is a low-power consumption module with built-in Wi-Fi solution designed by Hangzhou Tuya Technology Corporation” that is based on ESP8266 WiSoC with 1MB flash, 50 kB RAM. One person in the LetsControlIt forum thread linked above explains the stock firmware can be updated over-the-air via a Raspberry Pi 3/3+ […]

November 7, 2019November 7, 2019 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

NVIDIA Jetson Xavier NX SoM Delivers up to 21 TOPS for AI Workloads at the Edge

NVIDIA has just announced Jetson Xavier NX system-on-module, with the company claiming it is the “world’s smallest, most powerful AI supercomputer for robotic and embedded computing devices at the edge” with a 70x45mm “Jetson Nano” form factor, and delivering either up to 14 TOPS at 10 Watts or 21 TOPS at 15 Watts. The company expects the module to be used in small commercial robots, drones, intelligent high-resolution sensors for factory logistics and production lines, optical inspection, network video recorders, portable medical devices, and other industrial IoT systems. Jetson Xavier NX specifications: SoC – NVIDIA Xavier with 6-core NVIDIA Carmel ARM v8.2 64-bit CPU, 6MB L2 + 4MB L3 caches, and a 384-core NVIDIA Volta GPU with 48 Tensor Cores, 2x NVDLA deep learning accelerators delivering up to 21 TOPS at 15 Watts System Memory – 8 GB 128-bit LPDDR4x @ 51.2GB/s Storage – 16 GB eMMC 5.1 flash Video […]

October 23, 2019October 23, 2019 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Nordic Semi nRF52833 WiSoC Supports Bluetooth 5.1 Direction Finding, Works up to 105ºC

Nordic Semiconductors had added a new member to their RF52 multi-protocol wireless SoCs with nRF52833 that supports Bluetooth 5.1 direction finding and can operate in a wider temperature range between -40ºC and +105°C. The company also introduced nRF52833 DK development kit for Bluetooth Low Energy, Bluetooth mesh, Thread, Zigbee (802.15.4), and 2.4GHz proprietary applications, and some companies have already announced nRF52833 modules. Nordic Semi nRF52833 Bluetooth 5.1 SoC Key features and specifications: MCU Core – Arm Cortex-M4F @ 64 MHz Memory – 128 KB RAM Storage – 512 KB Flash Connectivity Bluetooth 5.1 @ 2 Mbps/1 Mbps/500 kbps/125 kbps 802.15.4 (Thread/Zigbee) @ 250 kbps 2.4 GHz proprietary @ 2 Mbps / 1 Mbps NFC-A tag TX power – Programmable from +8 dBm to -20 dBm in 4 dB steps Sensitivity Bluetooth 5: -103 dBm at 125 kbps; -98 dB at 500 kbps; -95 dBm at 1 Mbps; -92 dBm at […]

October 22, 2019 by Jean-Luc Aufranc (CNXSoft) - No Comments

Imagination iEW220 Low Power Dual-band 802.11n WiFi IP Solution Targets IoT, Automation and Wearables

Imagination-low-power dual-band WiFi IP solution

Imagination Technologies is better known for their PowetVR GPUs and as the previous owner of MIPS technology, but they do have other products as well and the company just announced their second generation 802.11n WiFi IP designed for low power applications Ensigma iEW220 is an IEEE 802.11a/b/g/n 1X1 SISO Wi-Fi IP solution comprised of RF, baseband and MAC, and supporting both 2.4GHz and 5GHz spectrum. iEW220 specifications: RF Features Dual-band 2.4 and 5 GHz RF including PA Power efficient AGC Optimized PLL power consumption Customized PA to minimize Tx power consumption Power optimized DAC/ADC design Integrated transmit/receive switch for RF Single pin RF antenna interface IEEE 802.11 PHY Support (2.4/5 GHz) IEEE 802.11b DSSS/CCK (up to 11 Mbps) IEEE 802.11a/g OFDM (up to 54 Mbps) IEEE 802.11n OFDM MCS 0-7, (20/40 MHz channels, up to 72.2/150 Mbps) Station, soft AP and Wi-Fi direct with up to four associated devices Tx […]

September 22, 2019 by Jean-Luc Aufranc (CNXSoft) - No Comments

PUCK 2 Bluetooth to IR Bridge Allows you to Control Appliances from your Android or iOS Phone

We’ve already seen there are several solutions to control IR appliances such as air conditioners or (dumb) televisions via your smartphone thanks to solutions such as ZaZa Remote that adds an IR transmitter to your 3.5mm audio jack or more recently via your USB-C port. If you don’t quite like having extra hardware connected to your smartphone WiFi to Infrared bridges such as the compact and omnidirectional Broadlink RM Mini 3 are cost-effective solutions, although you’d need one in every room where you wish to control appliances. I’ve recently noticed an even smaller “smartphone to IR” solution with PUCK v2 Bluetooth to IR bridge. The full technical details about PUCK 2 have not been made available, but we do know it’s a Bluetooth 4.2 to infrared remote bridge that transforms any iOS or Android device into a remote. The infrared LED has a range of about 4.5 meters, while Bluetooth […]

September 6, 2019September 6, 2019 by Stephen Vicinanza - 3 Comments

Mastak Modular Air Quality Monitor Kit Supports CO2, Dust, Formaldehyde, Ozone and other Sensor Modules

The Mastak Indoor Air Quality Monitor Kit Medium Systems Limited, a UK company has released the Mastak, SoMs designed in a mechanical range that allows for indoor air quality monitoring, with a data IoT cloud service, and communications that include NB-IoT, 5G, WiFi, BLE, and LTE-M. The system is a new addition to the air monitoring market place. There have been reports on other air quality monitors in past articles that covered quick start and user experience with Sonoff SC WiFi, vThings WiFi CO2 Monitor, and the ANAVI Gas Detector. The Specs The ecological modules are all compatible and contain processor, peripherals and the sensors for data monitoring and collection, as well as the necessary power electronics. The modules were designed too and allow the user to arrange the systems into custom arrangements and place in unique form factors. There are a number of options also, for even further expandability […]

August 31, 2019 by Stephen Vicinanza - 6 Comments

Pi-oT Raspberry Pi Add-on Board Targets Commercial & Industrial IoT Automation (Crowdfunding)

USA Based Startup Builds RPi Add-on Pi-oT, a Cleveland based startup has launched a Kickstarter campaign for a Raspberry Pi add-on for commercial and industrial IoT automation. The unit is a full mountable chassis with fan and DIN-rail that extends the Pi’s GPIO with 26-pin terminal connectors and provides 5x relays, 8x ADCs, and power outputs. We have reported on a variety of uses for the Raspberry Pi SBC, from home automation to development in IoT, to hobby projects, and in education settings. It is not surprising to see an automation module developed for IoT industrial applications around the popular and powerful SBC. The Choices The Kickstarter campaign has passed its low initial target and is set to ship at the end of October. There is an early launch discount on the unit’s price of $40 for commercial and $50 for industrial backers. That early bird type special is 15% […]

August 25, 2019 by Ayo Ayibiowu - 4 Comments

ESP32-MeshKit is a Development Kit for ESP32 Mesh Networking

The ESP8266 was a jewel in its peak, it ruled the maker’s world in the need for creating a low-cost WiFi module. Being Arduino compatible also furthered its glory then the ESP32 came in. ESP32 offered so much more than the ESP8266, and most importantly it was also affordable. With support for Bluetooth and WiFi, ESP32 was to open a new frontier for the development of Internet of Things applications. A major drawback of the affordable ESP32 was the lack of official support of mesh network for the chip, something that was easily possible with the ESP8266. Mesh network allows you to build a network of nodes that can communicate with each other, self heal, and many more possibilities. But thankfully, back in 2018, Espressif Systems released the ESP Mesh Development Framework (ESP-MDF) which sits on top of the IoT Development Framework (ESP-IDF), the official development framework for the chip. […]