automation News - Page 24 of 60 - CNX Software

July 4, 2021July 4, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Relay expansion board for Raspberry Pi includes 4.3-inch touchscreen display (Crowdfunding)

PiRelay 8-Channel Raspberry Pi touchscreen display

There are plenty of multi-relay boards for Raspberry Pi, but since those are often combined with an HMI for control, SB Components decided to offer an all-in-one solution with an expansion board equipped with eight relays and a 4.3-inch touchscreen display connected to a Raspberry Pi via HDMI and USB. PiRelay 8 specifications: Relays 8x relays with 3.3V/5V trigger signal Input – 250V AC/7A, 30V DC/10A Screw terminal blocks NO (Normally Open) and NC (Normally Closed) modes available Isolation – EL357NC optocouplers with current transfer ratio (CTR) of 50-600% at IF=5mA, VCE=5V Display support – Optional 4.3-inch touchscreen display with 800 x 480 pixels resolution, HDMI input for video, USB for touchscreen support. It also comes with a 3.5mm audio jack, an HDMI audio output, a speaker connector, and mounting holes for the Raspberry Pi. 40-pin GPIO header to connect a Raspberry Pi SBC (Pi 4, Pi 3B+, Pi 3, […]

June 15, 2021June 15, 2021 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

EdgeBox-RPi4 industrial controller offers RS485, RS232 interfaces, isolated DI/DO

EdgeBox-RPI4 Raspberry Pi CM4 industrial controller

OpenEmbed EdgeBox-RPi4 is an industrial controller based on Raspberry Pi Compute Module 4 fitted with up to 4GB RAM, 32GB eMMC flash, and a 2.4/5GHz WiFi & Bluetooth 5.0 wireless module. The controller exposes isolated RS485 & RS232 serial interfaces, as well as isolated digital inputs and outputs through a 16-pin terminal block, and provides Gigabit Ethernet and optional WiFI and 4G LTE connectivity options. EdgeBox-RPi4 specifications: SoM – Raspberry Pi Compute Module 4 (CM4) with Broadcom BCM2711 quad-core Cortex-A72 processor running up to 1.5GHz in either two default configurations: 1GB RAM, 8GB flash, no wireless module 4GB RAM, 32GB flash, dual-band WiFi 5 and Bluetooth 5 module Storage – M.2 socket for NVMe SSD up to 2TB (See expansion) I/O interfaces via 16-pin terminal block Industrial-grade isolated 2x DI (Digital Inputs), 2x DO (Digital Outputs) Industrial-grade isolated RS485 interface RS232 interface Connectivity Gigabit Ethernet RJ45 port Optional WiFI 5 […]

June 4, 2021June 4, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

reServer 2-bay multimedia NAS is equipped with an Intel Core Tiger Lake SBC

Seeed Studio has just introduced reServer dual-bay multimedia NAS based on Intel Core i3/i5/i7 Tiger Lake 11th generation processor. The networked storage device is based on ODYSSEY X86 V2 single board computer that offers an upgrade to the ODYSSEY-X86J4105 and ODYSSEY-X86J4125 Gemini Lake SBC’s. reServer comes with up to to 64GB dual-channel memory, dual 2.5GbE, support for two 3.5-inch SATA drives, HDMI and DisplayPort video output, and some USB 3.0/2.0 ports. reServer (preliminary) specifications: SoC (one or the other) Intel Core i3-1115G4 dual-core/quad-thread processor with 48 EU Intel UHD Graphics @ 400 – 1250MHz; 28W TDP Unnamed Intel Core i5 with 80 EU Intel Iris Xe Graphics G7 @ 400-1300MHz; 28W TDP Unnamed Intel Core i7 with 96 EU Intel Iris Xe Graphics G7 @ 400-1300MHz; 28W TDP Co-processor – Microchip ATSAMD21G18 32-Bit Arm Cortex-M0+ microcontroller System Memory – Up to 64GB dual-channel DDR4-3200 SDRAM via two SO-DIMM sockets Storage […]

May 24, 2021September 25, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Qualcomm 315 5G IoT modem announced for 5G IIoT applications

Qualcomm has announced the Qualcomm 315 5G IoT modem just a couple of days after the company’s introduction of Snapdragon 778G 5G SoC and M.2 5G card reference designs based on Snapdragon X65/62 modem. Qualcomm Technologies say it is their first purpose-built Internet of Things modem solution equipped with 5G connectivity and optimized for Industrial IoT (IIoT) applications. Qualcomm 315 5G IoT modem Qualcomm 315 5G IoT modem specifications: CPU – Cortex-A7 core running Linux Cellular connectivity 5G Technology – 3GPP Rel.15 5G NR Peak speeds – Download: 1.54 Gbps; upload: 330 Mbps Modes – SA (standalone), TDD & FDD RF – Adaptive antenna tuning, power tracking Sub-6 GHz Specs – 100 MHz bandwidth, 4×4 MIMO DL, 64 QAM DL/UL 4G LTE Technology – Rel.15 Cat.13 DL, Cat.5 UL Peak speeds – Download: 400 Mbps; upload: 75 Mbps LTE Modes – TDD & FDD LTE RF – 700 MHz to […]

May 20, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Sonoff & Tuya smart plugs found to transmit unencrypted passwords

There are many low-cost smart plugs based on ESP8266 that provide a convenient way to control lights or home appliances with your smartphone. But cybersecurity firm A&O IT Group found vulnerabilities in ITEAD’s Sonoff S26 and Ener-J Wi-fi (Tuya) smart plugs that would allow an attacker to easily access your wireless network. The first security vulnerability is pretty common and hard to exploit since it’s only a concern during the setup. Sonoff S26 starts itself into access point mode with ITEAD-1001xxxxxx SSID, and is set up through the eWelink app with the user not needing to know the password. But with older firmware is was needed, so ITEAD still shares the default password: 12345678 in the user manual, and it can be used to connect to the smart plug by anyone. But once configured, it’s not accessible anymore as the smart plug should be in client mode connected to your […]

May 13, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Arduino launches Portenta Machine Control industrial control unit

Arduino Portenta Machine Control is a low-power, industrial control unit powered by Arduino Portenta H7 board and designed to drive equipment and machinery through digital and analog I/O exposed through terminal blocks. The industrial control unit adds to the Arduino Pro family that was introduced in 2020 with support for the Arm Pelion IoT platform, the launch of the STM32H7-powered Arduino Portenta H7 industrial board, and joins another application-specific solution, namely the Arduino Edge Control board for smart agriculture launched last month. Arduino Portenta Machine Control specifications: Portenta H7 board with MCU – TMicro STM32H747XI Cortex-M7 @ 480 MHz + M4 @ 200 MHz MCU with 2MB dual-bank Flash memory, 1 MB RAM, Chrom-ART graphical hardware accelerator System Memory – 8MB SDRAM Storage – 16MB QSPI NOR Flash Connectivity – 10/100M Ethernet RJ45 port, WiFi & Bluetooth LE with u.FL antenna connector USB – 1x USB Programming Port I/O via […]

May 6, 2021May 11, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Z-Pi 7 Z-Wave gateway devkit works with Raspberry Pi and Orange Pi Zero boards

WiFi & Bluetooth are the most popular wireless protocols for home automation, alternatives like Zigbee and Z-wave have also been widely adopted, at least in some countries. And if you are interested in the latter, Aeotec has just introduced the Z-Pi 7 gateway development kit that lets you add Z-Wave connectivity to Raspberry Pi boards or Orange Pi Zero SBC with an expansion board connected over UART through the GPIO header. Aeotec Z-Pi 7 Z-Wave expansion board (ZWA025) specifications: Z-Wave connectivity Silicon Labs EFR32ZG14 Arm Cortex-M4 SoC @ 39 MHz with Series 700 and Gen7 technology Frequencies ZWA025-A: US Frequency 908.42 Mhz ZWA025-B: AU Frequency 921.42 Mhz ZWA025-C: EU frequency 868.42 Mhz TX Power – US: +9.3 dBm; EU: +4.8 dBm RX sensitivity – -97.5 dBm Range Indoor – US: 70+ meters; EU: up to 60 meters Outdoor – Up to 200 meters SmartStart native integration and S2 security. Z-Wave Plus Certified […]

May 4, 2021May 4, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Ebyte E104-BT11 Bluetooth Mesh module features Silicon Labs EFR32MG21 MCU

Ebyte E104-BT11 is a Bluetooth Mesh module offered in four variants with support for gateways (G) and node (N) versions, as well as PCB or IPEX antenna versions. Interestingly it is based on Silicon Labs EFR32MG21 Cortex-M33 microcontroller also found in ITEAD Zigbee 3.0 USB dongle, so it’s not impossible that it could be repurposed for Zigbee or Thread with firmware from Silabs. Ebyte E104-BT11 module specifications: Wireless MCU – Silicon Labs EFR32MG21 Arm Cortex-M33 microcontroller @ up to 80 MHz with DSP and FPU, up to 1024 kB flash, up to 96 kB RAM, 2.4 GHz IEEE 802.15.4 for Bluetooth LE, Zigbee, or Thread Wireless connectivity Bluetooth Mesh/BLE support with default firmware, up to 10,922 devices supported Max Tx power – 20 dBm Rx sensitivity- -88 to -97 dBm (-97 dBm typ.) Max data rate – 1Mbps Antenna – PCB antenna up to 200-meter range, or IPX antenna up […]