automation News - Page 13 of 60 - CNX Software

March 30, 2023March 30, 2023 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

SONOFF TX Ultimate “T5” smart touch wall switch support gestures, custom covers

Sonoff TX Utimate TX Smart Touch Wall Switch

SONOFF TX Ultimate smart touch wall switch, also known as the SONOFF T5, is another wireless switch from the company with up to 3 gangs, RGB color edge lights around the 86x86mm switch, as well as support for gestures and custom covers. Gestures like swipe left or right are possible because the full area of the SONOFF T5 switch acts as a touch sensor, and the RGB LEDs around the device enable ambient lights in the room at night. The switch can also provide haptic feedback to the user during use with a built-in speaker and vibration motor. SONOFF TX Ultimate specifications: Model numbers – T5-1C-86, T5-2C-86, T5-3C-86 depending on the number of buttons Wireless – 2.4 GHz Wi-Fi Input and Output power 1-gang: 100-240V~50/60 Hz up to 5A 2-gang: 100-240V~50/60Hz up to 10A (5A per gang max) 3-gang: 100-240V-50/60 Hz up to 15A (5A per gang max) Dimensions – […]

March 16, 2023March 17, 2023 by Jean-Luc Aufranc (CNXSoft) - 16 Comments

SONOFF MINIR4 review – A Tiny WiFi Smart Switch tested with eWelink app/web, and R5 controller

In this post, we’ll review the SONOFF Mini Extreme, also known as MINIR4, WiFi smart switch based on ESP32 wireless MCU by installing it into a wall-mounted light switch box and controlling it with both the eWelink mobile app for Android and the SONOFF R5 scene controller. SONOFF MINIR4 Installation We’ve already gone through the specifications, unboxing, and teardown in the announcement, so I’ll get straight to the installation part. Note this review was done with a light switch “box” (about 11x6cm) in Thailand, so your mileage may vary. The first challenge is that contrary to the similarly-sized SONOFF ZBMINI Extreme Zigbee switch, the MINIR4 WiFi switch requires a neutral cable, and most lights in Thailand are wired without a neutral wire, so I had to get the neutral wire from the outlet switch box underneath. When I call those “boxes” there are really holes in the wall here… Wiring […]

March 10, 2023March 11, 2023 by Paisit Wongsongsarn - 4 Comments

Review of SONOFF ZBCurtain Zigbee Smart Curtain Motor

Recently, Sonoff has released a new Zigbee product – called ZBCurtain – that turns your ordinary curtains into smart curtains. With this product, you can experience new benefits when using your curtains, such as automatic opening/closing, remote control through your mobile device, or setting up advanced automation to control your curtains based on factors such as temperature, humidity, or even using input from the other sensors. These smart capabilities provide benefits for your home or workplace, such as increased safety, energy savings, and convenience. The Sonoff Zigbee Curtain Motor (or ZBCurtain for shorts) can be integrated with your existing ordinary curtains, transforming them into smart curtains that can be controlled remotely via your smartphone, your voice commands, or even from a traditional remote controller. ZBCurtain Unboxing Within the package, we can find a wireless remote control, main motor units with a 3.5-meter long cable, and mounting brackets to attach the […]

March 9, 2023 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

SONOFF iHost Smart Home Hub enables local control of SONOFF, Tasmota, Matter home automation devices

SONOFF iHost is a Smart Home Hub that enables local control of SONOFF smart switches, lightbulbs, Zigbee sensors, and so on without having to require a connection to the cloud (e.g. eWelink). Future software upgrades will also add more devices such as the ones flashed with Tasmota firmware and any device compatible with the Matter IoT protocol. The gateway is based on either a Rockchip RV1109 SoC with 2GB RAM or a Rockchip RV1126 with 4GB RAM and offers 10/100M Ethernet, WiFi, Bluetooth LE, and Zigbee 3.0 connectivity, as well as a USB 2.0 port to allow for more connectivity. SONFF iHost Smart Home Hub specifications: SoC and Memory Rockchip RV1109 dual-core Arm Cortex-A7 @ 1.5 GHz with RISC-V MCU @ 400 MHz, 2D graphics engine, 1.2 TOPS NPU, 5MP H.264 and H.265 hardware video decoder and encoder, and 2GB DDR4 Rockchip RV1126 quad-core Arm Cortex-A7 @ 1.5 GHz with […]

March 8, 2023 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Home Assistant compatible “ESP 360 Remote” controls infrared and 433MHz appliances over WiFi (Crowdfunding)

ESP 360 Remote is an ESP32-based IR and 433 MHz RF remote with built-in sensors used to control home appliances over WiFi and that also integrates with Home Assistant open-source home automation framework. The open-source hardware design is comprised of a mainboard with an ESP32-WROOM-32E module, temperature, humidity, and light sensors, and a board on the top with nine infrared LEDs, one IR receiver, as well as a 433 MHz (or 315 MHz) RF receiver and transmitter with the receivers used for learning the code from the remote controls. ESP 360 Remote specifications: Wireless module – ESP32-WROOM-32E with ESP32 dual-core microcontroller 4MB flash 2.4 GHz WiFi and Bluetooth LE connectivity, built-in PCB antenna, fully compatible with ESPHome firmware Control interface 9x High Power IR LEDs to control devices in all directions (hence the 360 name) IR receiver to learn remote control codes 433 MHz (or 315 MHz) RF transmitter 433 […]

March 6, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Elfin-EW11 is a compact WiFi to RS485 unit with Modbus TCP support

Elfin EW11/EW11A is a small WiFi to RS485 unit with Modbus TCP/IP support that works either in the 5 to 18V DC (EW11) or the 5 to 36V DC (EW11A) input range. The WiFi to RS485 adapter is offered with either an internal or external WiFi antenna, the RS485 interface is exposed through an RJ45 port, and an RJ45 to terminal block cable is usually included, as well as a DIN Rail mount. Elfin EW11/EW11A specifications: MCU (I’m not sure which one is used, and the specs depend on where you look..) Unnamed Arm Cortex-M3 microcontroller @ 96 MHz with 2MB flash, 128KB SRAM (on the product page) OR Unnamed microcontroller @ up to 160MHz with 2MB flash, 352KB SRAM (on Aliexpress) Networking Wireless – 2.4 GHz WiFi 4 with up to WPA2PSK security, station, AP, or station+AP modes; internal or external WiFi antenna depending on the model. Wired – […]

February 27, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

8K AI embedded computer gets 4K HDMI input, WiFi 6, dual GbE interfaces, and more

Firefly EC-A3588Q 8K AI Embedded Computer

Firefly EC-A3588Q is a fanless 8K AI embedded computer powered by a Rockchip RK3588 processor and fitted with up to 32GB RAM, SATA or NVMe storage, offering dual Gigabit Ethernet, WiFi 6, Bluetooth 5.0, and optional 5G/4G cellular connectivity, dual 8K video outputs, etc… It is a higher-end and larger version of the Firefly EC-R3588SPC industrial mini PC based on the Rockchip RK3588S processor that adds a 4K HDMI input port, a VGA output port, gets two GbE interfaces and support for WiFi 6/Bt 5.0, offers more USB ports, and replaces some terminal blocks with DB9 interfaces for RS232, RS485, and CAN Bus interfaces. Firefly EC-Q3588Q specifications: SoC – Rockchip RK3588 octa-core processor with CPU – 4x Cortex-A76 cores @ up to 2.4 GHz, four Cortex-A55 cores @ up to 1.8 GHz GPU – Arm Mali-G610 MP4 quad-core GPU with OpenGL ES3.2 / OpenCL 2.2 / Vulkan1.1 support AI accelerator […]

February 26, 2023February 28, 2023 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

ePulse Feather ESP32 development board is optimized for low power consumption (in deep sleep)

Thingpulse ePulse Feather is an ESP32 development board following Adafruit’s Feather form factor and optimized for low power with 12 to 27 uA deep sleep power consumption. The board is based on the ESP32-WROVER with 8MB Flash and 8MB SPRAM and comes with a USB-C connector for charging the battery and programming through a CH9102F UART chip, as well as the I/Os headers provided by the Feather form factor. The board can be especially useful in battery-operated WiFi remote controls for home automation or other purposes that sleep most of the time until the user presses one of the buttons. ThingPulse ePulse Feather specifications: Wireless module – Espressif Systems ESP32-WROVER-E-N8R8 module with ESP32-D0WD-V3 or ESP32-D0WDR2-V3 dual-core microcontroller @ 240 MHz with 8MB QSPI flash, 8MB QSPI PSRAM USB – 1x USB Type-C port for power/charging and programming via CH9102F UART to TTL chip. Expansions – 12-pin + 16-pin headers with […]