som News - Page 74 of 78 - CNX Software

June 13, 2013June 13, 2013 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Variscite DART-4460 SoM is Small, Very Small, and Powered by TI OMAP4460

Variscite announced DART-4460, a new system-on-module based on Texas Instruments OMAP4460, with up to 1GB LPDDR2 RAM and 8GB eMMC flash. The key differentiating point of this module is its size (17 mm x 52 mm), which could make it the world smallest dual core module, although Logic PD’s DM3730 / AM3730 Torpedo SOM might be the smallest of all in single core configuration. DART-4460 system-on-module specifications: SoC – Texas Instruments OMAP4460 dual core cortex A9 @ 1.5 GHz max + PowerVR SGX540 GPU System Memory – 512 to 1024 MB LP-DDR2 Storage – Up to 8 GB eMMC + 2x SD / MMC Video – 1080p30 H.264 Encode / Decode Camera Interfaces – 2x CSI, 1x CPI Display HDMI 1.3a 1920 x 1080 24-bit RGB 1400 x 1050 24-bit DSI 1400 x 1050 4-wire resistive touch Connectivity Wi-Fi 802.11 b/g/n Bluetooth 4.0 Audio – Headphone, digital microphone, S/PDIF, Line […]

June 3, 2013June 3, 2013 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Emcraft Systems STM32F4 SoM and Starter Kit Run uCLinux From On-Chip Flash

Emcraft has recently announced a new system-on-module based on STMicro STM32F437 Cortex M4 micro-controller, as well as a starter kit based on the module that can run uCLinux directly from STM32F437’s 2MB on-chip flash, allowing a faster boot time, and AFAIK, this is the only Linux-ready STM32 platform available on the market. Here are the specifications of Emcraft Systems SOM-STM32F4: MCU – STMicro STM32F437 Cortex M4 @ 168 MHz with 256KB RAM and 2MB flash External Memory – 16MB PSRAM External Storage – 16MB NOR Flash Ethernet PHY (Optional) Connectors – 2x SoM Connectors with access to I/Os: USB, Ethernet, I2C, SPI, UART, LCD I/F, ADC, DAC, GPIO… Dimensions – 30 mm x 46 mm To speed-up development and for evaluation, the company also provides a starter kit composed of the STM32F4 SoM, and a baseboard (SOM-BSB-EXT) with the following main features: USB interface using USB-UART bridge connected to UART […]

June 2, 2013 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Critical Link MityARM-5CSX CoM Powered by Altera Cyclone V SoC

Earlier this week, I wrote about EnSilica eSi-ZM1, a system-on-module based on Xilinx Zynq7000 Extensible Processing Platform that comes with a dual core ARM Cortex A9 and FPGA fabric. It turns out Xilinx is not the only game in town, and Altera’s Cyclone V SoC, announced last December, also includes a dual core ARM Cortex A9 processor with Altera FPGA logic, and Critical Linux recently announced MityARM-5CSX computer-on-module based on this platform. Target applications include machine vision, scientific imaging, motor control, medical imaging and instrumentation, test and measurement, industrial instrumentation, as well as a military & aerospace. MityARM-5CSX specifications: SoC – Altera Cyclone V SX-U672 with FPGA logic and dual-core ARM Cortex-A9 up to 800MHz System Memory – 1GB DDR3 RAM, and 256MB DDR3 FPGA RAM (optional) Storage – 32MB QPSI NOR flash FPGA I/O fabric: PCIe hard core Up to 145 user-programmable I/O lines (including several 875MHz SerDes lanes) […]

May 30, 2013February 26, 2014 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

EnSilica eSi-ZM1 System-on-Module Features Xilinx Zynq XC7Z020 SoC

EnSilica has introduced the eSi-ZM1 SoM powered by Zynq ZC7Z020 SoC featuring 2 ARM Cortex A9 core, and an Artix-7 FPGA with 85K logic cells. The module also comes with 1GB RAM, 1GB NAND flash, and 16MB QSPI Boot Flash. ZC7Z020 SoC is notably used in ZedBoard development board, so if you have developed an application around this board, and want to commercialize it, using eSi-ZM1 module with your own custom baseboard could be an option. eSi-ZM1 system-on-module specifications: SoC – Xilinx Zynq XC7Z020 dual-core Cortex A9 processor @ 666 MHz, 85 K logic cells, 560 KB block RAM, and 220 DSP Slices. CLG484 package type System Memory – 1 GB, 1.35 V, 32-bit wide DDR3 SDRAM @ 533 MHz Storage: 1 GB, 1.8 V, 8-bit wide NAND FLASH 16 MB QSPI flash 1 or 2 Kb I2C EEPROM (and not 1MB as mentioned in the block diagram ) uSD card […]

May 25, 2013May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

Olimex A20-OLinuXino Prototype, AllWinner A20 SoM In The Work

Yesterday, Olimex showed their new A20-OLinuXino board. This AllWinner A20 board is still a prototype, and there are currently 3 of them only, but the good news is that it appears to be working, 50 developer edition boards will be manufactured shortly, and mass production should start in June. AllWinner A20 dual core Cortex A7 can clearly be seen in the middle of the board, but if you look close to the top left, you’ll see a marking: “A10-OLINUXINO-MICRO”. That’s because, as planned, they managed to design one PCB for both AllWinner A10 and A20 processors, and they’ll sell both versions. Olimex A10/A20-Olinuxino boards have the followings specifications: SoC – AllWinner A10 Cortex A8 processor or AllWinner A20 dual core Cortex A7 processor, both running @1Ghz System Memory – 512MB or 1GB DDR3 memory depending on model Storage – 4GB NAND Flash (optional), 2x microSD card slot, and SATA connector […]

March 19, 2013 by Jean-Luc Aufranc (CNXSoft) - No Comments

iWave Systems Launches RainboW-G12M-Q7 SoMs Powered by TI Sitara AM389x/DM816x Processor

iWave Systems, an embedded systems company based in Bangalore, India, has unveiled new Qseven Modules powered by Texas Instruments Sitara AM389x/DM816x ARM Cortex-A8 microprocessor clocked up to 1.5 GHz. Rainbow-G12M-Q7 modules target applications such as Single-Board computers, network and communication processing, industrial automation, human machine interface (HMI), medical electronic devices, video surveillance systems and interactive Point-of-Service (PoS) kiosks. Here are the modules specifications: CPU – TI AM389x/DM8168 ARM Cortex-A8 based Sitara Processor operating up to 1.5 GHz Memory: 1GB DDR3 SDRAM 128 MB NAND Flash On-Board Micro SD slot 230-pin Qseven Edge Connector: 1x PCIe v2.0 1x HDMI 1.3 2x SATA LVDS channel 1 x USB 2.0 Host | 1x USB 2.0 device I2S Port SD/SDIO SPI & I2C ports Expansion Connector: Gigabit Ethernet HD Video IN/OUT Ports Analog Video OUT Audio IN/OUT ports UART, GPIOs Form factor – Qseven R1.20 compatible (70mm x 70mm) Temperature Range – 0 to […]

March 17, 2013May 29, 2017 by Jean-Luc Aufranc (CNXSoft) - No Comments

BDD Group Announces AllWinner A10 Computer-on-Module

BDD Group (Black Dragon Development Group), a US based technology startup, has recently announced an AllWinner A10 Computer-on Module (CoM) targeting the industrial embedded market with support for Linux, Android and WinCE operating systems. The company did not provide complete specifications for the CoM/SoM, and they basically listed A10 specifications and added an RTC: SoC – AllWinner A10 ARM Cortex-A8 CPU + Mali-400 GPU VPU – Support for 2160P video decoding, 3D video decoding, various codecs such as VP8, AVS, H. 264 MVC, VC-1, MPEG-1,2,4, etc, and H.264 HP video encoding up to 1080p @ 30 fps or dual-channel 720p @ 30 fps. Display Multi-channel HD display Integrated HDMI 1.4 YPbPr, CVBS, VGA Multiple LCD interfaces, including CPU, RGB, LVDS up to Full HD Memory 32-bit DDR2/DDR3 up to 2GB SLC/MLC/TLC/DDR NAND up to 64 GB Boot Devices – NAND Flash, SPI NOR Flash, SD Card,USB RTC – Real time […]

February 28, 2013 by Jean-Luc Aufranc (CNXSoft) - No Comments

Ronetix SAMA5D3x-CM System-on-Modules Powered by Atmel SAMA5D3 eMPUs

Earlier this month, Atmel launched SAMA5D3 Cortex A5 embedded processor family, and Ronetix recently unveiled CPU modules based on the platform. SAMA5D3x-CM are SODIMM SoM based on SAMA5D3 series processor with 512MB DDR2, 256MB NAND Flash, 4MB SPI Flash, and Gigabit Ethernet. The key features of the modules are as follows: MCU – AT91SAMA5D3x series, 536 MHz ARM Cortex-A5 @ 1.2V (SAMA5D31, SAMA5D33, SAMA5D34 or SAMA5D35) System Memory – 512 MB DDR2 SDRAM, 32-bit Storage: 256 MB NAND Flash 16 MB NOR Flash (optional) 4 MiB Atmel SPI Flash One Wire 1024-bits EEPROM and 64-bits ROM Connectivity – 10/100/1000 MBit/s Ethernet Dimensions – 67.6x40mm (SO-DIMM 200 JEDEC MO-274 module) Temperature range – 0° +70°C or -40° to +85° C SAMA5D3-CM boards support Linux 3.6.9 and Android 4.0. Those are actually the modules used in Atmel SAMA5D3 evaluation kits, so Linux and Android support, starter kits, as well as documentation (except […]