lpwan News - Page 22 of 23 - CNX Software

November 11, 2016November 11, 2016 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

Marvin is a Plug and Play, Arduino Compatible, LoRa USB IoT Development Board (Crowdfunding)

LoRa appears to be one of the most popular LPWAN standards so far, with hobbyist development boards such as LoPy or LoRaONE, and we’ll soon have at least one more choice thanks to Marvin, a LoRa development board with a full size USB port. Marvin board specifications: MCU – Atmel/Microchip ATmega32u AVR MCU (same as Arduino Leonardo board) Connectivity – LoRa via Microchip RN2483; Supports both 868 MHz and 433 MHz frequency bands, on-board antenna USB – 1x USB, 1x micro USB port for power and programming Debugging – USB, and ISP header Expansion – 5x Grove connectors Power Supply – 5V via USB port Dimensions – N/A, but similar to USB flash drive The board can be programmed with the Arduino IDE, and they mention IBM Bluemix platform, and Node-RED, but overall details about documentation and software are scarce right now. One of the advantage of this form factor is […]

September 8, 2016February 25, 2018 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

u-Blox Unveils SARA-R4 LTE Cat M1 and SARA-N2 NB-IoT Modules for Professional IoT Applications

While I’ve mostly read about SigFox and LoraWan solutions for long range, low power, and low bitrate communications for the Internet of Things so far, there are many active of planned LPWAN standards for IoT applications, and 3GPP Release 13 standard stipulates two LTE LPWAN standards, namely LTE Cat M1 (eMTC) and LTE Cat NB1 (NB-IoT), with the former supporting 1 Mbps downlink and uplink peak data rates, and the latter 250 Kbps downlink, and 250 Kbps (multi-tone) or 20 Kbps (single tone) uplink data rates. U-Blox has released modules for both standard with SARA-R4 LTE Cat M1 and SATA-N2 NB-IoT modules. SARA-N2 Cat NB1 cellular module specifications: LPWAN Connectivity – 3GPP Release 13 NB1; NB-IoT bands: 5, 8, 20; downlink: 227 Kbps, uplink: 21 Kbps Positioning – GNSS via Modem Interfaces – 1x UART, 1x SPI, 2x GPIO, 1x DDC(I2C) for GNSS Features – Antenna supervisor, embedded IPv4 & […]

July 27, 2016 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Dragino LoRa/GPS HAT Board for Raspberry Pi Sells for $32

There are several ways to play with LoRaWAN protocol on the Raspberry Pi including RisingHF Discovery kit or Cooking Hacks LoRa Shield for Raspberry Pi, but the latter requires you to spend close to $100 just for the shield, the complete Lora discovery kit costs close to $400. Dragino Tech LoRa/GPS HAT board should be a more cost effective way to get started with LoRa on Raspberry Pi, as it sells for $32 + shipping on Tindie. Dragino LoRa/GPS HAT specifications: Connectivity LoRa Semtech SX1276/SX1278 transceiver @ 433/868, or 915 MHz (Country dependent, pre-configured in the factory) 168 dB maximum link budget. +20 dBm – 100 mW constant RF output vs. +14 dBm high efficiency PA. Programmable bit rate up to 300 kbps. GPS L80 GPS module based on Mediatek MT3339 SoC Horizontal Position Accuracy: autonomous <2.5 m CEP. TTFF@-130dBm with EASY (AGPS): Cold Start <15s,Warm Start <5s,Hot start <1s; […]

July 5, 2016July 6, 2016 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

RisingHF IoT Discovery is a LoRaWAN Evaluation Kit for Raspberry Pi

There are many current and upcoming long range low power wireless protocols for the IoT, but this morning I learned that South Korea launched a LoRa network (aka LoRaWAN), after another launch in the Netherlands earlier this year. While there are also some LoRa hobbyist kits such as LoraONE and LoPy being worked on, I decided to look on Aliexpress, but only got two products were listed: a LoRaWAN temperature and humidity sensor, and a LoraWAN USB modem. Both of them are made by a company called RisingHF. Among the products offered by the company, there’s a potentially interesting development kit called RisingHF IoT Discovery with the following components: 1x Raspberry Pi board 1x RHF0M301 LoRa Gateway based on Semtech SX1301 1x RHF4T002 adapter for Raspberry Pi and RHF0M301 1x RHF3M076 LoRaWAN USB AT Modem End point to connect to computer. It operates at 434MHz, 470MHz,868MHz, and 915MHz 3x RHF76-052 […]

May 10, 2016June 18, 2018 by Jean-Luc Aufranc (CNXSoft) - No Comments

LX IoT Cores Are Made for IoT and Wearables with Bluetooth LE, ANT+, 2G/3G, Sigfox, LoRa, and More

LX Group, an Australian company specializing in electronics design and embedded systems, has introduced three wireless modules for IoT and wearables which they call “LX IoT Cores”, and embeds various wireless protocol such as Bluetooth LE/Ant+, 2G/3G connectivity, WiFi, Lora, Sigfox, Taggle, etc… Let’s go though the main technical specs for the three modules, one of which it itself modular (hence the max and min size) depending on your requirements. LX Cellular Core (Right) MCU – STMicro STM32F217IGH6 ARM Cortex-M3 MCU @ 120 MHz with 1MB flash, 128kB RAM Storage – 1x micro SD card reader Communication Interfaces Radios – 2G/3G, WiFi, BLE, ANT+, provision for LoRa, Taggle, SigFox, optional GPS via daughter board Wired – USB, RS485, UART, SPI, I2C, Digital IO, ADC Sensors – Ambient Luminosity, accelerometer, gyroscope, magnetometer, temperature, humidity, air pressure, microphone USB – 1x micro USB port Misc – Reset and 2x user buttons, 2x […]

April 18, 2016April 18, 2016 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

LoRaONE is a Small LoRa IoT Development Board Based on Atmel SAMD21 MCU, Microchip LoRaWAN Module (Crowdfunding)

While there are many long range LPWAN standards, LoRa appears to be one of the most popular with boards such as LoPy, and now SODAQ LoRaONE module hitting crowdfunding campaigns. LoRaONE is powered by an Atmel Cortex M0+ micro-controller, features Microchip RN2483 or RN2903 LoRaWAN module, GPS, and various sensors. LoRaONE board specifications: MCU- Atmel ATSAMD21G18 ARM Cortex M0+ micro-controller @ 48 MHz with 256 KB flash memory, 32KB SRAM, and up to 16 KB EEPROM (by emulation) Connectivity LoRa via Microchip RN2483 (433/868 MHz) or RN2903 (915 MHz) module depending on your region GPS via u-blox EVA 7M USB – 1x micro USB port for power and programming Expansion headers (unpopulated) 14x digital pin, 12x for analog and 8x for PWM, plus UART, SPI and TWI (I2C) Analog output pin – 10-bit DAC External Interrupts: Available on all pins DC Current per I/O pin: 7 mA Operating Voltage – […]

April 8, 2016 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

SmartEverything is a Feature-Packed IoT Board with SigFox, Bluetooth LE, NFC and GPS Connectivity, Plenty of Sensors

Atmel MCU Madness is an informal competition on Twitter where people vote for their favorite development boards. We are now at the quarter finals, and beside the usual suspects such as Raspberry Pi and ESP8266 boards, I also noticed one board that I had never heard of: AXEL Elettronica’s SmartEverything based on Atmel SAM D21 Cortex M0+ and featuring SigFox, BLE, NFC, and GPS connectivity, as well as various sensors such as humidity and temperature, 9-axis motion sensor, and so on. SmartEverything board specifications: MCU – Atmel SAM D21 ARM Cortex-M0+ MCU @ 48 MHz with 256KB Flash, 32KB SRAM Connectivity SIGFOX via Telit LE51-868 S SIGFOX 868 MHz Wireless Module with 12 months of network access included Bluetooth 4.0 LE via TDK SESUB-PAN-T2541 module based on Texas Instruments CC2541 NFC via NXP NT3H1101FHK NFC with separate antenna (included) GPS/GNSS via Telit Jupiter SE868-A GPS/GNSS module with integrated antenna. Supports […]

January 20, 2016January 21, 2016 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

WAVIoT LPWAN Technology Powers Low Cost Smart Water and Electricity Meters

With the rise of IoT and M2M applications, more and more Low Power Wide Area Network (LPWAN) standards have been launched or being worked on, such as Sigfox, LoRa, 802.11ah “Hallow”, Weightless, etc… with all promising long range, low power consumption, and support for a high number of nodes. WAVIoT, a US startup founded in 2011, has decided to create its own solution called WAVIoT Nb-Fi (Narrowband Fidelity) that works in ISM bands, offers up to 50km line-of-sight range, supports up to 2 million nodes by gateway, lasts over 20 years on a small battery, and with WAVIoT said to cost as low as $2 per node. The technology is already available in smart electricity and water meters, and modules as shown in the picture below. Here are some of WAVIoT Nb-Fi technical specifications: DBPSK on physical layer of signal transmission; End-nodes transmit radio signal in 10-500 kHz bandwidth Minimum […]