IoT News - Page 37 of 182 - CNX Software

June 15, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Nordic Semi nRF7001 is a 2.4GHz WiFi 6 companion IC for nRF52, nRF53, and nRF91 wireless chips

Nordic Semi nRF7001 is the second nRF70 Series WiFi 6 companion IC. It is designed to add 2.4 GHz WiFi 6 connectivity to Nordic Semi nRF52 and nRF53 wireless SoCs and nRF91 cellular IoT system-in-package and support both client and access point mode. The nRF7001 follows the introduction of the nRF7002 dual-band (2.4GHz/5GHz) WiFi 6 companion IC last year, and target power or cost-optimized use cases where 5 GHz WiFi 6 may not be required or even suitable. Nordic Semi nRF7001 key features specifications: Complies with 802.11a/b/g/n/ac/ax 2.4 GHz band Wi-Fi 6 Station (STA) 1x Spatial Stream (SS) 20 MHz channel bandwidth 64 QAM (MCS7), 86 Mbps PHY throughput OFDMA (Downlink and Uplink) BSS coloring Co-existence interfaces, including Bluetooth LE Low-power and secure Wi-Fi for the IoT Target Wake Time (TWT) Security – WPA3 Host interface – SPI / QSPI Package – 6×6 mm QFN Since the nRF7001 is based […]

June 13, 2023June 13, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

CompuLab UCM-iMX93 – A miniature NXP i.MX 93 module with WiFi 5 & Bluetooth 5.3

CompuLab UCM-iMX93 is a miniature system-on-module powered by the new NXP i.MX93 Cortex-A55 AI processor family with up to 2GB RAM and 64GB eMMC flash. The tiny 38x28mm features a Gigabit Ethernet PHY, a WiFi 5 and Bluetooth 5.3 wireless modules, and plenty of multimedia, communication, and peripheral interfaces through two 100-pin high-density connectors including display and camera interfaces, USB ports, CAN FD, and up to 79 GPIOs. UCM-iMX93 specifications: SoC – NXP i.MX9352 or i.MX9331 dual-core/single-core Arm Cortex-A55 @ 1.5 GHz (industrial) / 1.7 GHz (commercial) with Arm Cortex-M33 real-time core @ 250 MHz, Arm Ethos U65 microNPU System Memory – 512MB to 2GB LPDDR4 Storage – 8GB to 64GB eMMC flash Networking Gigabit Ethernet PHY Certified WiFi 5 (802.11ac) and Bluetooth 5.3 BLE module (NXP 88W8997) 2x 100-pin 0.4mm pitch high-density UCM connectors Display 4-lane MIPI-DSI up to 1920 x 1080 @ 60Hz 4-lane LVDS up to 1366 […]

June 7, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

reTerminal DM – A Raspberry Pi CM4-powered 10.1-inch HMI controller

reTerminal DM 10-inch Raspberry Pi CM4 HMI terminal

Seeed Studio’s reTerminal DM is an upgrade to the Raspberry Pi CM4-powered reTerminal with a larger 10.1-inch touchscreen display and a greater range of features and interfaces for various industrial applications. Described as a “Panel PC, HMI, PLC, IIoT Gateway all-in-one device”, the new reTerminal DM notably supports 12V-24V variable DC input and optionally PoE power input, its front panel is rated IP65 for protection against liquids and dust, a range of wired and wireless connectivity options are offered, and it also includes some serial and digital input and output interfaces. reTerminal DM specifications: SoM – Raspberry Pi Compute Module 4 with Broadcom BCM2711 quad-core Cortex-A72 processor @ 1.5 GHz, up to 8GB RAM, up to 32GB flash Storage – Optional M.2 NVMe SSD via M.2 2280 Key-M slot Display – 10.1-inch display with 1280 x 800 resolution, 10-point capacitive touchscreen 400-nit brightness, 170° H/V viewing angle Video Output – […]

May 30, 2023 by Jean-Luc Aufranc (CNXSoft) - 7 Comments

NXP i.MX 91 single-core Cortex-A55 SoC to power Linux-based cost-optimized edge devices

NXP has just unveiled the NXP i.MX 91 single-core Cortex-A55 processor following the introduction of the i.MX 93 in 2021, and designed for cost-optimized edge devices running Linux. The NXP i.MX 93 processor comes with up to two Cortex-A55 cores, a Cortex-M33 real-time core, and an Ethos U65 microNPU, but targeting entry-level Linux systems, the NXP i.MX 91 processor does without the real-time core and the AI acceleration, while still integrating NXP EdgeLock Secure Enclave, and the company highlights support for multiple wireless connectivity options through companion chips such as the IW612 that supports Wi-Fi 6, Bluetooth 5.2, 802.15.4, and the new Matter protocol. NXP i.MX 91 specifications: CPU – Arm Cortex-A55 running at up to 1.4GHz with 256KB L2 cache System Memory – Up to 2.4GT/s x16 LPDDR4 with Inline ECC Storage 3x SD 3.0, SDIO 3.0, eMMC 5.1 1x Octal SPI including support for SPI NOR and SPI […]

May 22, 2023May 23, 2023 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Link.ONE LTE-M, NB-IoT, and LoRaWAN all-in-one LPWAN devkit is programmable with the Arduino IDE

RAKwireless Link.ONE is an all-in-one LPWAN development kit programmable with the Arduino IDE and based on nRF52840 Cortex-M4F 2.4 GHz multi-protocol wireless microcontroller, Semtech SX1262 LoRa RF transceiver, and Quectel BG77 LTE-M and NB-IoT module and comprised of components from the company’s WisBlock IoT prototyping platform. Besides the WisBlock modules, the kit includes everything to get started with four antennas for LTE-IoT, LoRaWAN, GNSS, and Bluetooth connectivity, a USB cable for power and programming, and a Monogoto SIM card with global coverage and 500MB of data valid for 10 years. Link.ONE hardware specifications: RAK19007 WisBlock base board with USB connector and Li-ion charger RAK4631 WisBlock core module with Nordic Semiconductor nRF52840 32-bit Arm Cortex-M4F microcontroller @ 64 MHz with 1 MB Flash, 256 KB RAM, Bluetooth Low Energy 5.0 protocol stack Semtech SX1262 LoRa/LoRaWAN RF transceiver with LoRaWAN 1.0.2 protocol stack (supports Class A & C), global coverage support: RU864, […]

May 22, 2023September 16, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

SparkFun “Datalogger IoT – 9DoF” no code platform supports over 50 Qwiic sensor modules

SparkFun “DataLogger IoT – 9DOF” is an ESP32-based data logger board that transfers data to a microSD card or wirelessly to the cloud and comes with firmware that can automatically detect over 50 Qwiic modules without any programming required from the user making it a so-called “no code platform“. The board comes with a 9-axis IMU sensor + magnetometer, and two Qwiic connectors, and the data is stored in CSV or JSON formats on a microSD card or sent to IoT cloud platforms such as Amazon AWS IoT, Microsoft Azure, or Mathworks ThingSpeak using protocols like MQTT or HTTP. SparkFun “Datalogger IoT – 9DoF” specifications: Wireless module – ESP32-WROOM-32E: ESP32 dual-core microcontroller 4MB flash 2.4 GHz WiFi and Bluetooth LE connectivity, built-in PCB antenna Storage – MicroSD card slot Sensors 6-axis IMU accelerometer & gyro (ISM330DHCX) Magnetometer (MMC5983MA) 2x Qwicc I2C connectors for additional sensors USB – 1x USB Type-C […]

May 19, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Laird RM126x LoRaWAN modules and development kits feature Silicon Labs EFR32 MCU, support P2P communication

Laird Connectivity has launched the RM126x series of ultra-low power LoRaWAN modules with the RM1261 based on SX1261 RF transceiver compliant with regulations in Europe, UK, Taiwan, Japan, India, and other countries, and the RM1262 based on Semtech SX1262 for USA, Canada, Australia, New Zealand, etc… The RM126x modules partially achieve their low power consumption through the use of a Silicon Labs EFR32 series microcontroller, and should be integrated into products for industrial, agriculture and forestry, smart cities, utilities monitoring, transportation, logistics, supply chain, healthcare monitoring, and retail. Laird RM126x specifications: MCU – Silicon Labs EFR32 Arm Cortex-M33 microcontroller with 512KB flash, 32KB SRAM LoRa connectivity RF transceiver – Semtech SX1261 or SX1262 Data rates LoRa 125kHz LoRa 250kHz LoRa 500kHz FSK 50kbps (as per RP002-1.0.3 ) Frequency Range (1) – 863 MHz – 870 MHz Frequency Range 2 – 902 MHz – 928 MHz LoRa Version Class – Version […]

May 11, 2023 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Banana Pi BPI-Centi-S3 – An ESP32-S3 board with an 1.9-inch TFT display and a rotary encoder

Banana Pi BPI-Centi-S3 ESP32-S3 display board

Banana Pi BPI-Centi-S3 is an ESP32-S3 WiFi & BLE IoT board with a 1.9-inch color TFT display, a rotary encoder, and a few I/Os, which offers an alternative to the T-Track ESP32-S3 board with AMOLED and trackball we covered a few days ago. The Banana Pi board also comes with a 2MB on-chip PSRAM, an 8MB SPI flash, a USB Type-C port for power and debugging, two buttons, a buzzer, and an RGB LED. Besides powering the board with its USB-C port, you can also connect a LiPo battery with charging support. Banana Pi BPI-Centi-S3 specifications: SoC – Espressif Systems ESP32-S3 dual-core Tensilica LX7 @ up to 240 MHz with vector instructions for AI acceleration, 512KB RAM, 2MB PSRAM, wireless connectivity Storage – 8MB SPI flash Connectivity via ESP32-S3 2.4 GHz 802.11 b/g/n Wi-Fi 4 with 40 MHz bandwidth support up to 150 Mbps Bluetooth Low Energy (BLE) 5.0 connectivity […]