gps News - Page 10 of 26 - CNX Software

April 14, 2022September 22, 2022 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Semtech LR1120 enables global asset tracking with multi-band LoRa, WiFi, and GNSS

Semtech LoRa Edge LR1120 is an ultra-low-power multi-band chip designed for global geolocation and asset tracking applications including direct satellite-connected Internet of Things (IoT) applications in supply chain management and logistics. Not only does the LR1120 features the usual sub-GHz LoRa radio found in most other chips from the company, but also comes with 2.4GHz LoRa and SATCOM S-Band support for satellite, as well as a GNNS radio compatible with GPS and Beidou, and a WiFi radio for indoor positioning (but no WiFi RTT/802.11mc support). Semtech LR1120 key features and specifications: Low-power high-sensitivity LoRa/(G)FSK half-duplex RF transceiver Worldwide ISM frequency bands support in the range 150 – 960MHz (Sub-GHz) and 2.4GHz, as well as 1.9-2.1GHz (S-Band) Low Noise Figure RX front-end High power PA path +22dBm in the Sub-GHz band Up to +11.5dBm in the 2.4GHz band LR-FHSS modulator Integrated PA regulator supply selector to simplify dual power +15/+22dBm with […]

January 25, 2022May 4, 2022 by Jean-Luc Aufranc (CNXSoft) - No Comments

RAKwireless introduces 16 new WisBlock modules with LoRaWAN, NFC reader, etc…

Wisblock LoRaWAN & NFC Reader wireless modules

RAKwireless will add new modules to its WisBlock IoT modular system every quarter. Last July, WisBlock family welcomed 14 new modules, and in September 2021, RAK11310 Raspberry Pi RP2040 LoRaWAN core was introduced together with a new baseboard and various sensor modules. This time around, the company launched 16 new Wisblock modules with two wireless modules, one adding LoRaWAN to an ESP32 core module, the other acting as an RFID and NFC card reader, as well as six sensor modules, and eight “interface” modules ranging from barcode scanners to keypads. WisBlock Wireless modules RAK13300 WisBlock LPWAN module based on Semtech SX1262 transceiver extends the communication abilities of the RAK11200 ESP32 WiFi & Bluetooth LE module with LoRa / LoRaWAN. RAK13600 WisBlock NFC Reader enables reading and writing of NFC tags like RFID cards and other NFC enabled devices using NXP PN532 chip. WisBlock Sensor modules RAK12013 WisBlock Radar Sensor – […]

December 16, 2021December 16, 2021 by Sponsored Post - No Comments

Tiny, high-precision GPS modules target UAV’s, wearables (Sponsored)

With the rapid development of the Internet of Things, positioning requirements are getting more strict notably with the need for higher precision and smaller GNSS modules. If you are looking for compact GPS modules that support a variety of satellite navigation systems, including China’s Beidou satellite navigation system BDS, the United States’ GPS, and Russia’s GLONASS with low power consumption (3.3V, 30mA), you may consider Ai-Thinker’s GP-01 and GP-02 GPS modules offering the smallest size. The GP-01 module has a total of 24 interfaces with five GPIO pins, while the GP-02 module has a total of 18 interfaces with three GPIO pins. These two modules are also available in development boards for ease of evaluation and development. Both are cheap, reliable, and based on the state of the art technologies. Thanks to its small size of only 10.3 x 9.9 x 2.4 mm, the GP-02 module can be easily embedded […]

December 14, 2021December 14, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Unsurv offline – An ESP32 GNSS receiver board with NFC, accelerometer (Crowdfunding)

Unsurv offline is a compact and lightweight board with ESP32 WiSoC, a GNSS receiver, an accelerometer, and NFC capabilities to help developers/users collect and analyze location data in a privacy-friendly way. Unsurv Technologies initially developed the board to better understand offline video surveillance with OpenStreetMap (OSM) data. It does so by using a database of camera locations from the OSM on the SD card, “counts” surveillance cameras as you walk past them, and you can then transmit data via NFC and visualize it on your smartphone. The accelerometer is used to wake up the board from deep sleep upon detection of motion. The company has now made the board open-source and other applications are also possible. Unsurv offline specifications: Wireless modules TTGO T-micro32 WiFi 4 and Bluetooth 4.2 module based on ESP32-PICO-D4 SiP with dual-core ESP32 processor, 4MB FLASH, ceramic antenna U-blox CAM-M8C (aka u-blox M8) module with concurrent reception […]

November 3, 2021November 3, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Conexio Stratus – An nRF9160 board with solar energy harvesting capability (Crowdfunding)

Conexio Stratus board is equipped with Nordic Semi nRF9160 System in Package (SiP) with LTE-M (eMTC) & NB-IoT cellular IoT connectivity as well as GPS support through a pair of u.FL connectors for antennas, together with 500MB of mobile data valid for ten years. Designed for battery operation, the devkit comes with built-in battery charging, monitoring, and energy-harvesting circuitry, plus an accelerometer and a temperature and humidity sensor that makes it ideal for prototyping cellular IoT systems such as asset-tracking applications, environmental monitoring, and smart-meter monitoring, among others. Conexio Stratus board Conexio Stratus specifications: SiP – Nordic Semi nRF9160 system-in-package with Arm Cortex M33 MCU, 1 MB Flash, 256 kB RAM, cellular IoT modem, and GPS. Cellular Connectivity 3GPP LTE release 13 Category M1 and NB1 compliant 3GPP release 14 NB2 compliant RF Transceiver for global coverage supporting bands: Cat-M1: B1, B2, B3, B4, B5, B8, B12, B13, B14, […]

August 2, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

TTGO T-Motion USB adapter offers LoRa and GPS for under $30

USB adapters are one of the easiest ways to add new features to existing hardware, and if you’d like to add LoRa connectivity and GPS tracking to any device or board with a USB board TTGO T-Motion USB adapter offers just that. Manufactured by LilyGO, the USB dongle is based on AcSiP S76G system-in-package that integrates an STM32 MCU with a Semtech SX1276 LoRa transceiver and GPS into a single. The GPS antenna is placed on the board inside the enclosure, while the external LoRa antenna is connected through an SMA connector. TTGO T-motion specifications: SiP – AcSiP S76G system-in-package with STMicro STM32L073x Arm Cortex M0+ MCU with up to 192 KB of Flash memory and 20 KB of RAM, Semtech SX1276 supporting global 868 MHz or 915 MHz ISM-Bands, Sony CXD5603GF GNSS receiver. Antenna Internal GPS antenna External LoRa antenna Host interface – USB 2.0 male port Misc – […]

July 27, 2021July 27, 2021 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Industrial Android/Linux mini PC ships with optional HDMI input, DTV tuner, 4G LTE modem

Industrial Android mini PC with HDMI input, ATSC, 4G modem

We’re seeing several companies known for their Android TV boxes switch to higher-margin industrial Android/Linux mini PCs with, for instance, Zidoo M6 mini PC powered by Rockchip RK3566 processor and designed for IoT applications, digital signage, and more. Geniatech APC820 is another industrial mini PC running either Android or Linux, on the older, yet more powerful Rockchip RK3399 SoC, and offering a different set of options including 4K or Full HD HDMI input, digital TV tuner, and/or a 4G LTE modem. Geniatech APC820 specifications: SoC – Rockchip RK3399 hexa-core processor with 2x Cortex-A72 cores up to 1.8GHz, 4x Cortex-A53 up to 1.4GHz, Mali-T860 GPU with support for OpenGL ES1.1/2.0/3.0/3.1, OpenCL, and DirectX 11.1 System Memory – 2GB or 4GB RAM Storage – 16GB eMMC flash by default (Option for 8GB to 128GB), MicroSD card slot Video Output HDMI 2.0 up to 4Kp60 Internal LVDS connector with backlight Internal eDP connector […]

July 26, 2021 by Jean-Luc Aufranc (CNXSoft) - No Comments

Pico 2G Expansion adds GSM/GPRS & GNSS to Raspberry Pi Pico (Crowdfunding)

You may have heard about the 2G/3G sunset with the older cellular networks being phased out in many countries. But it’s not always straightforward, as telecom operators may have to obtain regulators’ permission for the shutdown notably because of the eCall emergency services integrated into cars in Europe. Eventually, eCall will be migrated toward IMS Voice and 2G M2M services to 4G LTE IoT and 5G LPWA, but in the meantime, 2G networks are still operating in parts of the world, and UK-based SB Components has just introduced the Pico 2G Expansion board for Raspberry Pi Pico based on the SIM868 module. Raspberry Pi Pico 2G Expansion specifications: Compatible with Raspberry Pi Pico board Display – 1.14-inch LCD Cellular & GNSS Connectivity SIM868 module with GPRS multi-slot class 12/10, mobile station class B GSM 850/900/1800/1900 MHz GNSS – GPS/GLONASS/BDS Bluetooth 3.0 with audio support SIM card holder 2x SMA antenna […]