Arduino News - Page 77 of 117 - CNX Software

February 5, 2019 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

OpenISA VEGAboard Combines RISC-V and ARM Cortex-M Cores

OpenISA has launched an Arduino compatible RISC-V development called VEGAboard that features RV32M1 wireless microcontroller with a RISC-V RI5CY core, a RISC-V ZERO-RISCY core as well as Arm Cortex-M4F and Cortex-M0 cores, and a radio operating in the 2.36 GHz to 2.48 GHz range. An external NXP Kinetis K26 Arm Cortex-M4 MCU is added to the board for OpenSDA (Open-Standard Serial and Debug Adapter) debugging over a single USB cable. The board was offered for free, I’m just not sure when, but they are already out of stock. Hopefully, they’ll start selling the board soon enough. VEGAboard (RM32M1-VEGA) board key features and specifications: Ultra-low-power RV32M1 Wireless MCU supporting BLE, Generic FSK, and IEEE Std 802.15.4 (Thread) platforms IEEE Std. 802.15.4-2006 compliant transceiver supporting 250 kbps O-QPSK data in 5.0 MHz channels, and full spread-spectrum encoding and decoding Fully compliant Bluetooth v4.2 Low Energy (BLE) Reference design area with small-footprint, low-cost […]

January 25, 2019 by Jean-Luc Aufranc (CNXSoft) - No Comments

Google & Arduino Unveils the Arduino Science Kit Physics Lab

Google and Arduino have partnered together to developer and launch the Arduino Science Kit Physics Lab, the first official Arduino kit designed for middle school curriculum (ages 11 to 14). Based on Arduino WiFi MKR1010, the science kit will allow pupils to experiment with forces, motion, and conductivity, and log data with Google’s Science Journal “digital science notebook” app for Android. Arduino Science Kit Physics Lab kit content: Arduino MKR WiFi 1010 based on Microchip SAMD21 Cortex-M0+ MCU and Espressif Systems ESP32 WiSoC (WiFi + Bluetooth) Arduino Science Carrier Board 2x Silicone standoffs 1x Flat micro USB cable 1x Grove-compatible light sensor module 1x Grove-compatible temperature sensor module 1x Grove-compatible white LED module 3x Grove Cable 20cm – universal 4-pin connector 2x Double-ended cable: crocodile clip/banana plug (50 cm), 2x Double-ended cable crocodile clip/banana plug (20 cm) 1x Magnet 1x Hook-and-loop Velcro strap, 1x Hook-and-loop Velcro dot 2x PCB sticks, 1x […]

January 15, 2019 by Jean-Luc Aufranc (CNXSoft) - No Comments

XinaBox’s xChips Enable Modular Electronics for Makers & STEM Education

So today, I decided to have a look a 96Boards website to see if there was anything new from the community, and I came accross “X in a Box B901“, an “☒CHIP is designed to interface with the 96 Boards, such as the Dragonboard 410c. This provides an interface to support the ☒CHIP ecosystem, adding support for many additional sensors etc…” I had no idea what it was all about, so obviously I had to investigate. Xinabox (X in a Box) is an ecosystem of modular electronics boards used for developing, making products and learning. There are now over 70 modular xChip” with cores/CPUs, sensors, power, communication, output, and storage. They are interconnected together without wires, soldering, breadboards, and adapters are provided for Raspberry Pi, 96Boards, and other development boards. xChips can be sorted into 8 categories: Cores – MCU/CPI cores based on Microchip ATMega328P, SAMD21, ESP8266, or ESP32 with […]

January 11, 2019 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Edu-C Arduino Compatible Board Targets Education & Game Development

Sometimes learning can be boring, and a potentially good way to get kids more engaged is to learn by playing. Edu-C Arduino compatible board is designed to teach game development to kids old and young, so they have a lasting reward once they complete programming of the board, or they may decide to customize the game further. Edu-C hardware specifications: MCU – Microchip Atmel AVR328 microcontroller Display – 28×64 pixel OLED display + 1-digita 7-segment display Game Inputs – Left and right potentiometers Misc – 8x LEDs, left & right LEDs, RGB LED, on/off power switch, reset button, buzzer USB – 1x micro USB connector for programming (CH340) and power Power Supply – 5V via USB; LiPo battery support The board ships with a 200 mAh Lipo battery, and a charger. Educational materials are also provided, but only in French right now, except for some documents which are in English. There […]

January 11, 2019January 15, 2019 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

ANAVI Thermometer WiFi Board is Designed for Home Automation (Crowdfunding)

ANAVI Technology launched several open source hardware boards for the Raspberry Pi and ESP8266 maker communities in the past, starting with RabbitMax Flex home automation HAT for Raspberry Pi, and several others including ANAVI Light Controller ESP8266 board to control LED strips. All boards are designed with KiCad opensource EDA software, and I’ve tested several already such as ANAVI Infrared pHAT or ANAVI Light Controller, and found documentation to be very good and easy to follow. The company has now launched another ESP8266 board with ANAVI Thermometer that allows you to monitor temperature and humidity, effectively acting as a thermostat for home automation. ANAVI Thermometer specifications: SoC – Espressif Systems ESP8266 Tensilica L106 32-bit processor Connectivity – WiFi 802.11 b/g/n Display – Mini OLED display Build-in sensor – AM2302 (DHT22) temperature and humidity sensor Expansion Terminal block for DS18B20 waterproof temperature sensor UART pins 3x slots for I2C sensors Misc – […]

January 9, 2019December 20, 2022 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

TTGO T-Camera ESP32 Camera Board Comes with OLED Display, Sensors

ESP32 is now being used for AI workloads such as face detection with camera boards like ESP32-CAM, or the upcoming ESP-EYE board from Espressif Systems themselves, combined with ESP-WHO face detection and recognition framework. The two aforementioned board require you to use a phone to vizualize the results, unless you blink some LEDs or connect your own display. But the just released TTGO T-Camera board includes a 128×64 OLED display which should allow you to display face detection and/or recognition results, as well as a BME280 environmental sensor, a PIR sensor, and an optional fisheye lens. TTGO T-Camera board specifications: ESP32-WROVER-B Wireless Module SoC – ESP32 dual core Tensilica LX6 processor Memory – 8MB PSRAM Storage – 4MB SPI flash Connectivity – 2.4 GHz 802.11n WiFi 4, Bluetooth 4.2 LE Camera – 2MP OV2640 camera with normal or fisheye lens Display – 0.96″ 128×64 OLED display connected via SSD1306 I2C […]

January 6, 2019April 13, 2021 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Sony Spresense Board Review with NuttX based Spresense SDK

Sony Spresense Arduino compatible board with audio and global navigation satellite systems (GNSS) support and its extension board launched in Japan this summer. The company has now expanded markets, and is offering the boards in the United States and Europe as well. They also tasked an agency to send samples to various reviewers, and I got selected to receive one as well. I’ll start the review by checking out the hardware, shortly discuss software development options, and report my experience with Spresense SDK. Sony Spresense Unboxing I received two packages… … one the main board, and the other for the extension board. The main board package only comes with CXD5602PWBMAIN1 board and an information sheet. The top of the board includes a reset button, four user LEDs, a power LED, a boot recovery button, the camera interface, Sony CXD5247 power management and audio analog interface chip (Black on the photo below, […]

December 28, 2018March 4, 2019 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

ClockworkPi GameShell Review – Part 1: Unboxing & Assembly Guide

ClockworkPi Gameshell is a portable retro gaming console kit designed to be hackable being powered by Allwinner R16 processor to run Linux, as well as an Arduino compatible Atmel AVR MCU. It’s partially open source hardware with PDF schematics, and firmware source code available on Github. The device launched last year on Kickstarter, raised close to $300,000, and started shipping to backers last summer. The company has now sent me a sample for review, so let’s have a look. The first part of the review will be more than just an unboxing, since the game console is meant to be assembled by the end user, and I’ll report my experience doing so. ClockworkPi Gameshell Unboxing The kit comes in a fairly large package that reads “GameShell – Redefine Portable Game Console” and lists the main specifications with quad core Cortex A7 processor, WiFi and Bluetooth connectivity, 1GB RAM, 16GB micro […]