Video Category - Page 58 of 323 - CNX Software

January 19, 2022February 18, 2022 by Jean-Luc Aufranc (CNXSoft) - 13 Comments

10.1-inch RPI All-in-One PC review with Raspberry Pi 4

A couple of months ago I received “RPI All-in-One”, a 10.1-inch touchscreen display for Raspberry Pi boards, listed the specifications, checked out the package content, installed a Raspberry Pi 4 inside the display before booting my new all-in-one (AiO) PC successfully. I’ve now had time to spend more time with the PC/display and see how it performs under various conditions. I also tested HDMI and USB-C input features with a laptop and mini PC. Fan or fanless operation? After updating Raspberry Pi OS, I ran sbc-bench.sh script together with rpi-monitor to see how the Raspberry Pi 4 with 1GB RAM would perform under load with the (noisy) fan enabled.

sbc-bench v0.9.1

Installing needed tools. This may take some time. Done.
Checking cpufreq OPP. Done (results will be available in 11-15 minutes).
Executing tinymembench. Done.
Executing OpenSSL benchmark. Done.
Executing 7-zip benchmark. Done.
Checking cpufreq OPP. Done (17 minutes elapsed).

perl: warning: Setting locale failed.
perl: warning: Please check that your locale settings:
	LANGUAGE = (unset),
	LC_ALL = (unset),
	LC_ADDRESS = "en_GB.UTF-8",
	LC_NAME = "en_GB.UTF-8",
	LC_MONETARY = "en_GB.UTF-8",
	LC_PAPER = "en_GB.UTF-8",
	LC_IDENTIFICATION = "en_GB.UTF-8",
	LC_TELEPHONE = "en_GB.UTF-8",
	LC_MEASUREMENT = "en_GB.UTF-8",
	LC_TIME = "en_GB.UTF-8",
	LC_NUMERIC = "en_GB.UTF-8",
	LANG = (unset)
    are supported and installed on your system.
perl: warning: Falling back to the standard locale ("C").
It seems neither throttling nor frequency capping has occured.

Memory performance:
memcpy: 2595.9 MB/s (0.8%)
memset: 3398.3 MB/s (2.7%)

7-zip total scores (3 consecutive runs): 5556,5650,5565

OpenSSL results:
type             16 bytes     64 bytes    256 bytes   1024 bytes   8192 bytes  16384 bytes
aes-128-cbc      61981.49k    76335.40k    82773.25k    84199.42k    84355.75k    84393.98k
aes-128-cbc      62224.25k    76254.36k    82779.39k    84461.91k    84757.16k    84825.43k
aes-192-cbc      55900.34k    67052.89k    71500.80k    73121.11k    73362.09k    73203.71k
aes-192-cbc      55869.41k    66963.52k    71835.14k    72934.74k    73471.32k    73465.86k
aes-256-cbc      50541.63k    59834.26k    63387.14k    64413.70k    64634.88k    64760.49k
aes-256-cbc      50646.47k    59735.02k    63384.92k    64461.14k    64648.53k    64629.42k

Full results uploaded to http://ix.io/3MfY. 

In case this device is not already represented in official sbc-bench results list then please
consider submitting it at https://github.com/ThomasKaiser/sbc-bench/issues with this line:
| RPi 4 Model B Rev 1.1 / BCM2711 rev B0 | 1500 MHz | 5.10 | Bullseye armhf | 5590 | 62100 | 64690 | 2600 | 3400 | - | [http://ix.io/3MfY](http://ix.io/3MfY) |

sbc-bench v0.9.1

Installing needed tools. This may take some time. Done.

Checking cpufreq OPP. Done (results will be available in 11-15 minutes).

Executing tinymembench. Done.

Executing OpenSSL benchmark. Done.

Executing 7-zip benchmark. Done.

Checking cpufreq OPP. Done (17 minutes elapsed).

perl: warning: Setting locale failed.

perl: warning: Please check that your locale settings:

LANGUAGE = (unset),

LC_ALL = (unset),

LC_ADDRESS = "en_GB.UTF-8",

LC_NAME = "en_GB.UTF-8",

LC_MONETARY = "en_GB.UTF-8",

LC_PAPER = "en_GB.UTF-8",

LC_IDENTIFICATION = "en_GB.UTF-8",

LC_TELEPHONE = "en_GB.UTF-8",

LC_MEASUREMENT = "en_GB.UTF-8",

LC_TIME = "en_GB.UTF-8",

LC_NUMERIC = "en_GB.UTF-8",

LANG = (unset)

are supported and installed on your system.

perl: warning: Falling back to the standard locale ("C").

It seems neither throttling nor frequency capping has occured.

Memory performance:

memcpy: 2595.9 MB/s (0.8%)

memset: 3398.3 MB/s (2.7%)

7-zip total scores (3 consecutive runs): 5556,5650,5565

OpenSSL results:

type 16 bytes 64 bytes 256 bytes 1024 bytes 8192 bytes 16384 bytes

aes-128-cbc 61981.49k 76335.40k 82773.25k 84199.42k 84355.75k 84393.98k

aes-128-cbc 62224.25k 76254.36k 82779.39k 84461.91k 84757.16k 84825.43k

aes-192-cbc 55900.34k 67052.89k 71500.80k 73121.11k 73362.09k 73203.71k

aes-192-cbc 55869.41k 66963.52k 71835.14k 72934.74k 73471.32k 73465.86k

aes-256-cbc 50541.63k 59834.26k 63387.14k 64413.70k 64634.88k 64760.49k

aes-256-cbc 50646.47k 59735.02k 63384.92k 64461.14k 64648.53k 64629.42k

Full results uploaded to http://ix.io/3MfY.

In case this device is not already represented in official sbc-bench results list then please

consider submitting it at https://github.com/ThomasKaiser/sbc-bench/issues with this line:

| RPi 4 Model B Rev 1.1 / BCM2711 rev B0 | 1500 MHz | 5.10 | Bullseye armhf | 5590 | 62100 | 64690 | 2600 | 3400 | - | [http://ix.io/3MfY](http://ix.io/3MfY) |

No throttling was detected, and the temperature never exceeded 56°C in a room with an ambient temperature of 26°C. I then disconnect the fan, but it turns out the fan can also be easily disabled in the OSD menu […]

January 14, 2022 by Jean-Luc Aufranc (CNXSoft) - 11 Comments

Khadas Tea – A MagSafe Hi-Fi headphone amplifier to play lossless audio on smartphones (Crowdfunding)

From this side of the Internet, Khadas is better known for their single board computer, but the company has also made Hi-Fi audio products starting with the Khadas Tone in 2018 as an add-on board for Khadas VIM/VIM2 SBC, followed by Khadas Tone 2 Pro mini desktop Hi-Fi system in 2020. The latest audio product from Khadas is a smartphone accessory with Khadas Tea being a thin MagSafe-compatible magnetic Hi-Fi headphone amplifier based on aptX HD and LDAC capable Qualcomm QCC5125 Bluetooth SoC and ESS ES9281AC Pro DAC that sticks to the back of your phone. Khadas Tea specifications: Bluetooth Audio SoC – Qualcomm QCC5125 Bluetooth 5.0 audio chipset USB DAC – ESS ES9281AC Pro Amplifier – RT6863D (Buffer Stage) Audio I/O 3.5mm headphone jack Built-in stereo microphone for making and receiving calls over Bluetooth Sampling Rate USB: up to 32bit 384KHz @ PCM, or DSD 256 (Native) Bluetooth: up […]

January 9, 2022 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Reolink Go Plus 4G review – Part 2: A Solar-powered 4G LTE security camera with person & vehicle detection

Last month, I received Reolink Go Plus 4G smart security camera with 4G LTE connectivity, vehicle/human detection support, and powered by a solar panel. In the first part of the review, I did an unboxing, added the camera to the Reolink Android app, and confirmed it worked with my DTAC SIM card. I’ve now installed the camera and had time to test more of its features, so I can report my experience with the security camera. Reolink Go Plus 4G camera and solar panel installation I wanted to use the camera near the gate that’s outside of (reliable) WiFi range. So I found a piece of hardwood to which I attached the mounts of the camera and solar panel… … and attached it to the wall. My current installation works for testing, but it’s not the most secure as the camera is quite visible and only placed a little over […]

January 7, 2022January 7, 2022 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

Board with 25 RGB LEDs is offered with ESP32-C3 or ESP32-Pico-D4

In case you are in need of a tiny WiFI or Bluetooth-connected board with an RGB LED matrix, two have shown up on Banggood with basically the same 25 RGB LED design , except “C3FH4 RGB” board is based on ESP32-C3 RISC-V SoC, while the other, named “PICO D4 RGB“, features ESP32-Pico-D4 SiP (System-in-Package). The boards are cute and the main purpose is probably for decoration/ornament, but I’d imagine if you purchase a few they could also be used as an experimentation/education platform for mesh networking, using the ESP Mesh Development Framework (ESP-MDF) for instance. C3FH4 RGB / PICO D4 RGB board specifications: SoC/SiP C3FH4 RGB board – ESP32-C3FH4 SoC with RISC-V core @ 160 MHz, 4MB flash, 2.4GHz Wi-Fi, and Bluetooth 5 LE with Long-Range support PICO D4 RGB board – ESP32-PICO-D4 system-in-package with ESP32 dual-core Xtensa processor @ 240 MHz, 2.4GHz Wi-Fi and Bluetooth dual-mode, 4MB flash Ceramic […]

December 29, 2021December 29, 2021 by Sponsored Post - 10 Comments

10,000 mAh Graphene power bank fully charges in 27 minutes (Sponsored)

Most power banks are made of Lithium batteries that charge in 3 to 4 hours and are good for around 500 charge cycles. But Elecjet Apollo Ultra is a different beast equipped with a 10,000 mAh Graphene battery that enables fast charging in just 27 minutes and offers a much longer lifespan with over 2,500 charge cycles. In other words that means Apollo Ultra power bank is 5x faster and lasts 5x longer than most lithium-based power banks. Another way to look at it is that this graphene-enhanced 10,000mAh power bank can gather enough power in just 7 minutes to fully charge your phone. It can fast-charge your phone up to three times, charge two devices at once, and passthrough charging lets you charge Apollo Ultra at the same time. Elecjet Apollo Ultra specifications: Battery Capacity – 10,000 mAh or 40 Wh Full Charge Time – 27 minutes USB ports […]

December 29, 2021 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

Raspberry Pi UPS HAT takes two 18650 batteries (Crowdfunding)

Raspberry Pi UPS solutions have been available for years with products like PiJuice Zero, PiVoyager, or LiFePO4wered/Pi+. But the team at SB Components has designed another UPS HAT for Raspberry Pi with a holder for two 18650 batteries. The HAT is designed for 5V operation up to 2.5A, connects with the Raspberry Pi SBC through the I2C bus from the 40-pin GPIO header, and is equipped with a 0.91-inch OLED for information display. UPS HAT for Raspberry Pi specifications: Power Input – 8.4V/2A via DC jack Power Output – 5V up to 2.5A through LDO chip (GPIO header and 2x USB ports) Display – 0.91-inch OLED Host interface – I2C Misc – On/Off switch Battery support 18650 Lithium battery (not included) via holder for two batteries Battery reverse indicator Charging and voltage monitoring via TI INA219 I2C chip Battery voltage balancing with Hycon HY2213 Battery protection IC (Hycon HY2120) Dimensions […]

December 24, 2021December 24, 2021 by Jean-Luc Aufranc (CNXSoft) - 6 Comments

Newt 2.7-inch wireless display offers high refresh rate with SHARP’s Memory-in-Pixel (MiP) technology (Crowdfunding)

Newt is a battery-powered, always-on, ESP32-S2 wireless display with a 2.7-inch display leveraging SHARP’s Memory-in-Pixel (MiP) technology to provide an experience similar to E-Ink displays but with a much faster refresh rate. The wireless display can connect to the Internet to retrieve weather, calendars, sports scores, to-do lists, quotes, and whatever you’d like. Since it is powered by an ESP32-S2 microcontroller you can program with the ESP-IDF framework, Arduino, MicroPython, or CircuitPython. Newt display specifications: WiFi module – Espressif ESP32-S2-WROVER module with ESP32-S2 single-core Xtensa LX7 processor @ 240 MHz with 4 MB flash and 2 MB PSRAM Display – 2.7-inch, 240 x 400 pixel SHARP MiP LCD with “high-contrast, high-resolution, low-latency content with ultra-low power consumption”, reflective mode to eliminate the need for a backlight. USB – 1x USB Type-C port for programming, power, and charging Expansion – I2C Qwiik connector Misc Micro Crystal RV-3028-C7 RTC (45nA power consumption) […]

December 23, 2021December 23, 2021 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

HUENIT modular robot arm takes 3D printer, laser engraver, suction, AI camera modules (Crowdfunding)

Most robot arms are designed to carry and manipulate payloads, but HUENIT modular robot arm is much more versatile as besides a traditional suction module, the robot supports modules such as a 3D printer, laser engraver, pen holder for drawings, and a creator module for let people designed their own. The robot arm can hold payloads of up to 750 grams, have a reach of up to 39 cm without module, supports WiFi and Bluetooth connectivity, and can also optionally be fitted with a 2MP AI camera module based on Kendryte K210 RISC-V processor with built-in AI accelerators. HUENIT specifications: Robot arm 4-axis Payload up to 750 grams Reach – 390mm without module Repeatability – 0.05mm Precision – 0.1mm Speed – Up to 500mm/s Storage – MicroSD card slot USB – 1x USB-C port Wireless – WiFI and Bluetooth Misc – UART, external stepper Power Supply – 24V DC input, […]