Video Category - Page 30 of 322 - CNX Software

August 4, 2023August 4, 2023 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Home Assistant-compatible 5-24V LED strip controller ships with Sound Reactive WLED firmware

SMLIGHT A1-SLWF-03 is a Home Assistant-compatible addressable RGB LED strip controller based on an ESP32 WiFi and Bluetooth microcontroller that supports 5V to 24V LED strips. The unit is equipped with a built-in digital microphone used by the Sound Reactive WLED firmware to make the RGB LED strip follow the rhythm and tempo of the music, an IR receiver, and a sensor button. SMLIGHT A1-SLWF-03 specifications: SoC – ESP32 dual-core microcontroller with WiFi 4, Bluetooth 4.2/5.x, and 16Mbit flash 4-pole terminal block for RGB LED strips Supported strips – WS2812B, WS2811, WS2813, WS2815, APA102, LPD8806, WS2801, SK9822. Voltage Range – 5-24V DC Up to 2,000 LEDs are supported at 35 fps with two outputs or 3,000 LEDs at 25 fps with two outputs (about 33 to 50-meter LED strips with 60x LEDs per meter) Multiple A1-SPWF-03 controllers can be synced together for controlling even more LED strips. USB – 1x […]

August 4, 2023August 4, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

CORE-V MCU Devkit features open-source 32-bit RISC-V core, Amazon AWS IoT connectivity, Mikrobus expansion, VGA camera

The CORE-V MCU DevKit is an open-source hardware board based on the CORE-V microcontroller featuring the open-source OpenHW CV32E40P0 RISC-V MCU core and a Quicklogic ArticPro 2 eFPGA. The board offers wireless connectivity to Amazon AWS through an ESP32-C3 AWS IoT ExpressLink module, a MikroBus connector for expansion, a VGA camera module, JTAG and serial debugging, as well as a temperature sensor and a few buttons. The development kit can be powered by its USB Type-C port (5V) or a DC jack taking 5V to 18V DC. CORE-V MCU devkit specifications: Microcontroller – CORE-V MCU OpenHW CV32E40P RISC-V processor core (in-order 4-stage RISC-V RV32IMFCXpulp CPU based on RI5CY from PULP-Platform) with 512KB SRAM, boot ROM Quicklogic ArticPro 2 eFPGA Storage – 4MB QSPI flash Wireless – Espressif AWS IoT ExpressLink Module for AWS IoT cloud interconnect Camera – Himax HM01B0 ultra-low-power QVGA (320×240) CMOS image sensor as found in the […]

August 3, 2023September 1, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

CrowView adds a 14-inch portable monitor to your laptop for $115 and up (Crowdfunding)

CrowView 14 inch laptop monitor extender

Elecrow CrowView is a lightweight 14-inch portable monitor designed to be attached to your laptop adding a secondary monitor to it through a clamping structure that works with laptops having a 13-inch to 16.5-inch display. We’ve seen this type of laptop monitor extension for years, and you’ll find various models on Amazon. But the Elecrow is now offering the CrowView at a significantly lower price than competitors especially if you pledge $114.90 for the super early bird reward on Kickstarter. The regular price ($179) can still be interesting as in this price range you’d usually get an 11-inch or 12-inch display. CrowView specifications: 14-inch IPS display with 1920×1080 resolution, 60 Hz refresh rate, 400 nit brightness Compatible with 13-inch to 16.5-inch laptops with 4 to 8mm thick displays thanks to a telescopic snap 230° hinge enabling face-to-face mode. Ports Mini HDMI port for video input 2x full-featured USB Type-C port […]

July 31, 2023 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

e-con systems See3CAM_24CUG USB 3.1 global shutter camera review

e-con Systems See3CAM_24CUG a full HD color global shutter USB 3.1 Gen 1 camera based on an Onsemi AR0234CS CMOS image sensor capable of capturing moving scenes at up to 120 fps. This global shutter camera is especially useful for robotics and other applications that may require a high frame rate such as Automatic Number Plate Recognition (ANPR), Autonomous Mobile Robots (AMR), gesture recognition, drones, barcode scanners, factory automation, conveyor monitoring cameras, and traffic monitoring systems. e-con Systems sent a See3CAM_24CUG USB global shutter camera sample to CNX Software for review. I’ll go through an unboxing before testing in Ubuntu with both an AMD Ryzen 7 2700U laptop and a Raspberry Pi 4 single board computer. It happens to be based on the same sensor as the e-CAM20_CURB camera for Raspberry Pi 4 that we reviewed last year. See3CAM_24CUG specifications ON Semiconductor AR0234CS CMOS sensor with 1/2.6″ optical form-factor Global […]

July 30, 2023 by Jean-Luc Aufranc (CNXSoft) - No Comments

Robo Pico review – A Raspberry Pi Pico W-based motor & sensor control board tested with BocoBot robotic kit

Robo Pico Review Raspberry Pi Zero W robot

Cytron Robo Pico is a carrier board for the Raspberry Pi Pico (W) specially designed for robotics & IoT applications with a 2-channel DC motor driver, four servo motor ports, and seven Grove I/O connectors to connect various sensors and/or actuators. When the company asked us to review the Robo Pico board, I noticed they had a car robotic kit based on the board called the BocoBot that comes with installation videos and five tutorials including obstacle avoidance movement with ultrasonic sensors, light search, line following, and WiFi remote control. So I asked for the full kit to make the review more fun and interesting. Robo Pico board Robo Pico specifications: Supported MCU board – Raspberry Pi Pico/Pico W and compatible Motor control 2x DC Motor terminals with Motor status LEDs for each motor terminal 2x motor test buttons for each motor terminal Header to connect to 4x servos Expansion […]

July 23, 2023January 7, 2024 by Jean-Luc Aufranc (CNXSoft) - 21 Comments

CZUR ET24 Pro book scanner review with Ubuntu 22.04 Linux

CZUR ET24 Pro book scanner Ubuntu review

The CZUR ET24 Pro is a professional book scanner that works with Windows, macOS, and Linux, so I decided to review it in Ubuntu 22.04 since we are fans of hardware that can interface with Linux at CNX Software.

If you haven’t already, I strongly recommended reading the unboxing part of the CZUR ET24 Pro review, as we go through the specifications, show the various interfaces of the scanner, showcase the various accessories, and also try it out with the HDMI interface in presentation/preview mode. It will help you better understand the second part of the review, where we’ll connect the CZUR ET24 Pro scanner to a Ubuntu 22.04 laptop using the provided USB cable.

July 18, 2023July 18, 2023 by Jean-Luc Aufranc (CNXSoft) - 1 Comment

Yahboom DOFBOT 6 DoF AI Vision robotic arm for Jetson Nano sells for $289 and up

Robotic arms can be expensive especially if you want one with AI Vision support, but Yahboom DOFBOT robotic arm designed for NVIDIA Jetson Nano offers a lower cost alternative as the 6 DoF robot arm sells for about $289 with a VGA camera, or $481 with the Jetson Nano SBC included. We previously published a review of the myCobot 280 Pi robotic arm from Elephant Robotics, and while it’s working well, supports computer vision through the Raspberry Pi, and is nicely packaged, it sells for around $800 and up depending on the accessories, and one reader complained the “price tag is still way too high for exploration“. The DOFBOT robotic arm is looking more like a DIY build, but its price may make it more suitable for education and hobbyists. DOFBOT robotic arm main components and specifications: SBC – NVIDIA Jetson Nano B01 developer kit recommended, but Raspberry Pi, Arduino, […]

July 13, 2023July 22, 2023 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

Affordable RTK GNSS receiver supports USB or/and Ethernet interfaces (Crowdfunding)

HYFIX’s RTK Rover is an affordable, centimeter-accurate RTK (Real-time Kinematic) GNSS receiver with either a USB interface or/and Ethernet connectivity with the latter relying on a Raspberry Pi 4 SBC. As a reminder, RTK relies on traditional GNSS networks like GPS and works with a Base station at a fixed location and a Rover station that can be fitted to a drone or mobile robot in order to determine the position with up to one-centimeter accuracy. The RTK Rover from HYFIX is equipped with a dual-band LC29H GNSS module from Quectel and an onboard IMU sensor that tracks position through dead reckoning when GNSS connectivity is lost. RTK Rover specifications: MiniPCIe card with Dual-Band L1/L5 RTK Receiver (Quectel LC29H) Antenna – External antenna (6x5x2 cm) connected to SMA connector Sensor – IMU Interfaces USB Type-C port for power and serial Interface Ethernet Rover Kit only – Gigabit Ethernet and USB ports […]