Video Category - Page 191 of 327 - CNX Software

December 5, 2016December 6, 2016 by Jean-Luc Aufranc (CNXSoft) - 12 Comments

$46 TS100 Digital Programmable Soldering Iron is Controlled by STMicro STM32 MCU

I’m now using a $4 soldering iron which works most of the time for what I’m doing, but sometimes it does not seem to heat quite fast enough which may cause problems. I’m not soldering that often, so I did not think about getting a better one, but I’ve just come across an TS100 digital & programmable soldering iron with a OLED display showing the current temperature, and controlled by an STMicro STM32F103T8U6 micro-controller. The soldering iron also includes an accelerometer which allow the soldering iron to know when you are using it, so the temperature drops if it is inactive for over 5 minutes (sleep mode), and after 10 minutes of inactivity, the soldering iron automatically turns off. TS100 soldering iron key specifications: OLED Display USB – 1x micro USB port for configuration Temperature Range – 100 to 400 °C; 15 seconds to heat to 300 °C @ 19V; […]

December 1, 2016December 1, 2016 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Hack Autonomous Driving into Your Car with Open Source Hardware Comma Neo and Open Pilot Software

George Hotz setup Comma.ai company and worked on a commercial project called Comma One to add autonomous driving to some car models, but then the US highway authorities started to ask questions and promised ever increasing fines if he could not comply with some specific safety regulations/requirements, and eventually he decided to cancel the project due to the regulatory burden. A few weeks passed since the cancellation, and he has now released Open Pilot auto-pilot software and Comma NEO a work-in-progress open source hardware platform connecting to Qualcomm Snapdragon 820 powered OnePlus 3 smartphone to run the software. The system is said to implement “Adaptive Cruise Control (ACC) and Lane Keeping Assist System (LKAS) for Hondas and Acuras”, and performs about the same as “Tesla Autopilot at launch, and better than all other manufacturers”. Open Pilot currently only supports the Acura ILX 2016 with AcuraWatch Plus and the Honda Civic […]

December 1, 2016 by Jean-Luc Aufranc (CNXSoft) - 16 Comments

reMarkable 10.3″ Digital Notepad and e-Reader is Designed to Feel Like Paper

If you like to take notes with pen and paper, but would prefer a digital solution to store your note, there are already some solutions like Boogie Board and Rocketbook, but reMarkable offers much more that the other two with a 10.3″ E-Ink touchscreen display and pressure sensitive pen capable of detecting 2048 levels of pressure sensitivity, it allows to read books as any e-readers, and also write your own notes on a blank piece of “paper” or existing digital documents, drawing sketches, and save & share the results. The whole user experience is supposed to feel as if you were reading and writing on paper. reMarkable tablet specifications: SoC – ARM Cortex A9 processor @ 1 GHz (Likely NXP i.MX6 series processor since they support EPD interfaces) System Memory – 512 MB DDR3L Storage – 8GB internal storage good for around 100,000 pages Display – 10.3″ monochrome digital paper […]

November 29, 2016November 30, 2016 by Jean-Luc Aufranc (CNXSoft) - 10 Comments

Grid-EYE Breakout Board is a $49 Low Resolution Thermal Camera Module

Thermal cameras can be really expensive pieces of equipment, and even the cheap 60×60 thermal cameras available on Aliexpress costs a little over $200. However, PURE Engineering has made an breakout board with Panasonic Grid-EYE infrared 8×8 array sensor that allows you to experiment with the technology, or integrate into your own projects for just $49. Grid-EYE breakout board features: Panasonic Grid-EYE AMG8834 64 pixel infrared / thermal camera sensor with 60 degree viewing angle using MEMS thermopile technology Pinout compatible with Arduino Zero, ST-NUCLEO board, and other 3.3V boards with I2C, VDD, GND, INT, and AD pins PUREModules PCB edge connectors with UART, GPIO, to interface with the company’s IoT board Power Supply – On-board regulator handles 3 to 5V input The Panasonic sensor transfers thermal presence, direction, and temperature values over I2C. The company wrote a demo for the module with an Arduino sketech and a Processing sketch […]

November 25, 2016 by Jean-Luc Aufranc (CNXSoft) - 14 Comments

Firefly-RK3399 Development Board Will Fly with Rockchip RK3399 Hexa-core Processor

ARM Cortex A72 class development boards are usually quite expensive, and cheaper boards like Mediatek X20 development board ($200) appears to be out of stock very often, and software support is limited to Android 6.0. But things look to improve soon, as T-Chip is about to release Firefly-RK3399 development board powered by Rockchip RK3399 hexa-core Cortex A72/A53 processor. Firefly-RK3399 (preliminary) specifications: SoC – Rockchip RK3399 hexa-core bit.LITTLE processor with dual core Cortex A72 up to 2.0 GHz and quad core Cortex A53 processor with ARM Mali-T860MP4 GPU with OpenGL 1.1 to 3.0 support, OpenVG 1.1, OpenCL and DX 11. System Memory – 2 to 4 GB DDR3 Storage – 16 to 32 GB eMMC flash + micro SD card Video Output & Display Interfaces – HDMI 2.0 up to 4K @ 60 Hz, eDP 1.2 interface, YUV interface, 1x MIPI DSI interface Video Decode – 4K VP9 and 10-bit H.265 […]

November 25, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Sevenhugs Smart Remote is a Universal Direction Aware WiFi, Bluetooth and IR Remote Control (Crowdfunding)

You may have all sort of remote control devices around your home from the traditional IR remote control for your TV, air conditioner, audio system etc.., as well remote control apps for WiFi or Bluetooth objects such as smart light bulbs or water pumps running on your smartphone. Sevenhugs Smart Remote promises to replace them all, and all you have to do is to point the remote control to your devices, or setup virtual actions to your door or window to order a Uber drive or check the weather. Sevenhugs Smart Remote specifications: MCU – ARM Cortex-M4 @ 200 MHz System Memory – 32 MB RAM LCD – 3.43″ touch screen IPS display; Dragontrail damage ans scratch resistant cover glass, anti-fingerprint & anti-glare Wireless Connectivity – IR transceiver, 802.11 b/g/n WiFi and Bluetooth 4.1 LE connectivity USB – USB C port for charging Sensors – Indoor positioning sensor, accelerometer, gyroscope, […]

November 23, 2016November 25, 2016 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

Zidoo Releases Digital Signage SDK for X8 and X9S Android TV Boxes

Zidoo X9S and X8 are Android 6.0 + OpenWrt TV boxes powered by Realtek RTD1295 processor with HDMI input supporting PIP, UDP broadcasting and video recording, which works reasonably well despite some 4K video decoding limitations. The company has now released a “digital signage SDK” – which I’d rather just call a digital signage demo – working on either device on github, but you can still study the source code in order to build your own. Some of the possible features showcased in the demo include: Digital Signage (AD) player as shown above with video, picture and scrolling text Multi Views display (HDMI IN + Video playing + Web browsing) Multi Videos decode Screen rotation Screen zoom in / out Display output resolution switch HDMI IN player HDMI IN picture in picture (PIP) So it’s not a total solution, just an “SDK” showing what can be done with media files, and you’d still have to write your own app managing content updates (from storage or network), as well as some content management software. Two apks are used: […]

November 18, 2016June 18, 2018 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

$49 Dashbot Car Dashboard Assistant is Powered by C.H.I.P Pro Allwinner GR8 Module (Crowdfunding)

Most companies specializing in development boards may sell a few accessories for their boards, but usually leave product design to their customers. Next Thing Co. does that too, but the company also produces some products like PocketCHIP portable Linux computer & retro game console, and more recently Dashbot, a voice controller assistant for your car’s dashboard powered by CHIP Pro module. Dashbot hardware specifications: CPU Module – CHIP Pro with Allwinner GR8 ARM Cortex A8 processor @ 1.0 GHz, 512MB NAND flash, 256 DDR3 RAM, 802.11 b/g/n WiFi, Bluetooth 4.2 External Storage – micro SD slot Display – Red LED display Audio – 32-bit audio DSP for beamforming & noise suppression; fairfield audio pre-processor with 24-bit ADC; high fidelity MEMS microphone array (106 dB dynamic range) USB – 1x USB host port Power Supply – 5V via USB port or 12V via power port (aka cigarette lighter) + backup LiFePo4 […]