Video Category - Page 103 of 329 - CNX Software

June 16, 2020August 24, 2021 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

CrowPi2 Raspberry Pi 4 Laptop Doubles as Electronics Learning Kit (Crowdfunding)

CrowPi2 Raspberry Pi 4 Laptop with Detachable Keyboard

CrowPi portable learning kit for Raspberry Pi 3 B+ and Pi Zero boards was launched in 2018. It comes with a 7″ display, several sensors, buttons, a breadboard, and more all packed in a small suitcase. Elecrow has now started a new crowdfunding campaign on Kickstarter to fund the second generation portable electronics learning kit: CrowPi2 which looks much more like a laptop than a suitcase found in the first model thanks to a large display, and a detachable keyboard placed on top of the electronic prototyping/learning area. It’s also more powerful thanks to the latest Raspberry Pi 4 SBC. CrowPi2 specifications: Compatible Raspberry Pi boards – Raspberry Pi 3B/B+, Raspberry Pi 4 Display – 11.6-inch 1920×1080 IPS screen Camera – 2MP camera Audio – Built-in microphone and stereo speaker; 3.5mm audio jack Keyboard – 2.4GHz detachable wireless keyboard (QWERTY only) with touchpad Sensors and Modules under the keyboard: Displays […]

June 14, 2020June 14, 2020 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

ZS1100A IoT Power Meter Supports Sigrok Open-Source Software (Crowdfunding)

A few months ago, I tested Qoitech Otii Arc power meter & DAQ system designed for developers of IoT devices, and fount out it would be incredibly useful to developers of battery-operated devices since it shows voltage and current graphs synchronized with the serial output making it easy to see where software might be optimized. The system can also capture analog and digital signals from the DUT and emulate batteries with user-defined characteristics. But this weekend, I’ve come across a very similar solution with ZS1100A IoT power meter that also happens to be compatible with Sigrok open-source signal analysis software, and the corresponding Pulseview GUI. ZS1100A IoT power meter specifications: Measurements Output Voltage Range – 0 to 6 V programmable in 10 mV steps with +/- 5mV accuracy, Current Measurement Range – -0.5 A to 1.5 A (linear range) with < 0.1 μA resolution, accuracy of 1% of measured value […]

June 13, 2020 by Jean-Luc Aufranc (CNXSoft) - 18 Comments

Dune HD RealBox 4K TV Box Runs Android and Linux on Realtek RTD1395 SoC

Realtek RTD1395 processor is designed for 4K HDR TV boxes and set-top boxes. Equipped with a quad-core Cortex-A53 processor and Mali-470 GPU it offers a lower-cost alternative to Realtek RTD1295 and RTD1296 with the same 4K video processing and playback capabilities. So far, we had seen it in TV boxes designed for operators and Banana Pi BPI-M4 single board computer, but Dune HD RealBox 4K TV box is the first RTD1395 consumer device sold directly to end-users. Dune HD RealBox 4K specifications: SoC – Realtek RTD1395 quad-core Cortex-A53 processor with Mali-470MP4 GPU System Memory – 2 GB RAM Storage – 16 GB flash, MicroSD card slot Video Output – HDMI 2.0a up to 4Kp60 HDR and AV port (composite) Audio – Optional S/PDIF, analog stereo audio via AV port, digital audio via HDMI port; HDMI audio pass-through to AV receiver Video Playback 4Kp60 HDR/HDR10+ with 10-bit H.265 and VP9 profile-2, […]

June 11, 2020November 7, 2020 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

DFI Ryzen Embedded R1606G SBC Review – Part 2: Windows 10 Enterprise LTSC

DFI GHF51 is an AMD Ryzen Embedded R1606G SBC for industrial application that’s about the size of the Raspberry Pi Model B board, and after checking out the hardware in the first of part of the review “DFI GHF51 AMD Ryzen Embedded SBC Review – Part 1: Unboxing and Assembly“, I’ve now had time to play with the board running the pre-installed Windows 10 Enterprise LTSC operating system. DFI GHF51 Hardware Connections Since there aren’t any full-sized USB ports, you’ll need a USB-C hub to get started as you’ll probably want to connect a USB keyboard and mouse for development and testing, as well as a Micro HDMI cable to connect to a TV or display. I tried both MINIX NEO C Plus and Dodocool DC30S USB Type-C hubs, and the former did not work at all, while the latter mostly worked. I also connected an HDMI cable to the […]

June 7, 2020June 6, 2020 by Jean-Luc Aufranc (CNXSoft) - 9 Comments

STM32 based Indoor Air Quality Sensor Connects to Raspberry Pi or Arduino (Crowdfunding)

Indoor Air Quality Sensor Raspberry Pi Arduino

Even before the COVID-19 lockdown, people spent most of their time indoors (around 90% according to some studies), so it’s important to monitor air quality and other metrics like light and sound levels in our homes, workplaces, schools, cars, etc… Metriful Sense indoor environment monitor does just that by reporting multiple metrics such as temperature, humidity, particle concentration, etc… over I2C to microcontroller or processor boards such as Arduino or Raspberry Pi. Sense hardware specifications: MCU – STMicro STM32G071KB Arm Cortex-M0+ microcontroller @ 64 MHz with 128 KB Flash, 36 KB SRAM Sensors Bosch Sensortec BME680 4-in-1 air quality sensor with relative humidity, barometric pressure, ambient temperature, and gas (VOC). Vishay VEML6030 ambient light sensor Knowles SPH0645LM4H-B MEMS microphone Optional – Shinyei PPD42 particle sensor unit I/Os – 10-pin unpopulated header with air particles sensor input, light and sound interrupt outputs, I2C, VPU pin for 3.3V/5V selection, GND, VDD, VIN […]

June 5, 2020November 3, 2020 by Jean-Luc Aufranc (CNXSoft) - 2 Comments

M5Stack Atom Echo Coin-Sized Bluetooth Speaker is Powered by ESP32-PICO-D4 SiP

M5Stack has just launched Atom Echo, a coin-sized programmable Bluetooth speaker based on Espressif Systems ESP32-PICO-D4 system-on-package. The company sent me an early sample to play with before launch… but let’s have a look at the specification before checking the device further. Specifications: SiP – Espressif Systems ESP32-PICO-D4 system-in-package with ESP32 dual-core processor @ 240MHz Wi-Fi, BLE 4.0 and 4MB flash Audio 0.5W/NS4168 I2S speaker SPM1423 PDM microphone Expansion 5-pin + 4-pin headers with 6x GPIOs, UART, 5V, 3.3V, GND 4-pin digital Grove header with 2 I/Os, 5V and GND Misc – RGB LED (SK6812), Function (Top – G39 pin) and reset buttons (side), IR LED Power Supply – 5V/500mA via USB-C port Dimensions – 24 x 24 x 17mm (plastic material) Weight – 10 grams The Bluetooth speaker is really small, but you may think CNXSoft has big hands and fat fingers so it makes the speaker smaller than […]

June 5, 2020June 5, 2020 by Jean-Luc Aufranc (CNXSoft) - 8 Comments

$11 HDMI to USB 2.0 Video Capture Dongle Supports up to 1080p30 Resolution

Over the years we’ve covered several HDMI input solutions for PiP, video capture, and/or RTSP streaming and some of the most popular options where Realtek RTD1295 based TV boxes such as Zidoo X9S or LAKE I Home Cloud. But there’s now a more cost-effective option with “Camlink” HDMI to USB 2.0 converter which you can connect to your PC or single board computer. It’s compatible with UVC video class, supports up to 1080p30, and offers HDCP compatibility. Best of all it’s really cheap with pricing starting at around $11 on Aliexpress including free shipping and also available on eBay. Key features and specifications: HDMI input up to 4K resolution (3840×2160 @ 30 Hz) with 8/10/12 bit color depth support; Up to 15-meter cable (AWG26) Video Output up to 1080p30 using YUV or JPEG modes Audio – L-PCM Compatible with common video software such as VLC, OBS, Amcap, etc … Compliant […]

June 5, 2020 by Jean-Luc Aufranc (CNXSoft) - No Comments

Fingernail-sized BLYST840 nRF52840 Module Features Bluetooth 5.2, Thread, Zigbee and 46 I/O (Crowdfunding)

Canada based I-SYST inc has designed a tiny nRF52840 module about the size of a fingernail. BLYST840 module fully leverages the capability of Nordic Semi’s wireless microcontroller with Bluetooth 5.2, Thread, and Zigbee connectivity, and exposes 46 I/Os. BLYST840 specifications: Wireless MCU – Nordic Semiconductor nRF52840 Arm Cortex-M4F microcontroller @ 64 MHz with 1 MB flash, 256 KB RAM Connectivity Bluetooth 5.2 up to 2 Mbps, -96 dBm sensitivity for long-range; Up to 111 dB link budget; Bluetooth Mesh IEEE 802.15.4 radio support for Thread & Zigbee NFC-A Built-in ceramic antenna Output power – Adjustable from +8 dBm to -20 dBm 46 I/O pins exposed via pads around the edges of the module including QSPI/SPI/2-wire/I2S/PDM/QDEC Programmable Peripheral Interface (PPI) SPI interface @ 32 MHz Quad SPI interface @ 32 MHz EasyDMA for all digital interfaces USB 2.0 (12 Mbits) 12-bit/200K SPS ADC Security Arm TrustZone Cryptocell 310 128-bit AES/ECB/CCM/AAR co-processor […]