Intel FPGA Category - Page 8 of 8 - CNX Software

October 16, 2014 by Jean-Luc Aufranc (CNXSoft) - 4 Comments

Lark Board Powered by Altera Cyclone V SX ARM Cortex A9 + FPGA SoC

Farnell/Element14 has quietly announced Lark Board from their subsidiary Embest Technology in September. The board is powered by an Altera Cyclone V ARM Cortex-A9 dual-core + FPGA processor with high speed transceivers, runs Debian 7.4, and targets medical instruments, video surveillance and industrial control applications. Lark board specifications: SoC – Altera Cyclone V SX (5CSXFC6D6F31I7N) with a dual core Cortex A9 processor (HPS – Hard Processor System) @ 800 MHz, FPGA fabric including up to 110K logic cells (LE), and high speed transceivers (2 PCIe hard IPs and 9 3Gbps transceivers) System Memory – 1GB DDR3 SDRAM for HPS, 1GB DDR3 SDRAM for FPGA Storage – 4GB eMMC Flash + micro SD card slot Audio/Video Interfaces – HDMI, VGA, and 24-bit LCD interface supporting 4-wire touch screen Data Transfer Interfaces: High-resolution serial digital interface (SDI) that supports SMD standard interface and provides a SDI TX and a SDI RX 12-bit […]

August 11, 2014 by Jean-Luc Aufranc (CNXSoft) - No Comments

Parallax Propeller 1 P8X32A Open Source Multi-core MCU

Lots of electronics devices are now powered by open source software such as Linux, open source hardware is not as wide-spread, but gaining tracking traction thanks to the like of Arduino, Beagleboard.org, Olimex, and many projects on crowdfunding websites, and now we even start seeing some open source silicon. Existing open source processors include LEON3 (SparkV8) MCU, OpenRisc, and just very recently, LowRISC, based on 64-bit RISC-V instruction set architecture, has been announced with the backing of some of Raspberry Pi co-founders, Google ATAP, etc… and is currently being developed at the University of Cambridge, UK. Parallax Propeller 1 P8X32A is another MCU which has been open sourced last week. Propeller 1 P8X32A had however been released in April 2006, and can be sourced as a 40-pin DIP chip for prototyping, and 44-pin QFP and QFN for production, and come with the following key features: Power Requirements: 3.3 VDC […]

February 1, 2014February 1, 2014 by Jean-Luc Aufranc (CNXSoft) - No Comments

DENX MCV Systems-on-Module Feature Altera Cyclone V SX FPGA + ARM SoC

DENX Computer has announced a new systems-on-module (SoM) powered by Altera Cyclone V dual ARM Cortex A9 + FPGA SoCs. DENX MCV SoMs also feature 1GB DDR3, 256 NAND Flash, and various memory interfaces and peripherals including PCI Express Gen2 and high-speed serial 3.125Gb transceivers. DENX MCV SoM specifications: SoC – Altera Cyclone V SoC with FPGA and two ARM Cortex A9 core @ 800 MHz. Four SoC are available: A2 – 5CSXFC2C6U23C7N – 25KLE, 36 DSP blocks, 6 transceivers 3.125Gbit/s A4 – 5CSXFC4C6U23C7N – 40KLE, 58 DSP blocks, 6 transceivers 3.125Gbit/s A5 – 5CSXFC5C6U23C7N – 85KLE, 87 DSP blocks, 6 transceivers 3.125Gbit/s A6 : 5CSXFC6C6U23C7N – 110KLE, 112 DSP blocks, 6 transceivers 3.125Gbit/s System memory – 1 GB DDR3 Storage – 256 MB NAND Flash, 256 Mbit Configuration Device HPS (Hard processor system) peripherals Clock distribution Default configuration: Gigabit Ethernet UART, SPI, I²C CAN USB Additional optional interfaces: One […]

January 25, 2014January 26, 2014 by Jean-Luc Aufranc (CNXSoft) - 5 Comments

ARM Unveils Cortex-M Prototyping System Based on Altera Cyclone V FPGA

Before micro-controllers or processors are manufactured, simulation is performed in (usually) expensive boards based on FPGA chips from Altera or Xilinx, and once designers have found the system to work as expected, they can move to the next phase and work on the actual silicon. ARM has just released V2M-MPS2 Cortex-M Prototyping System for MCU / SoC / ASIC designers working on Cortex-M processors. Key features: Altera Cyclone V FPGA with ~150K LE 4x 2MB ZBTRAM (32-bit each, with two of them forming a 64-bit memory). ZBT = Zero Bus Latency 16MB PSRAM (16-bit) Touch screen LCD module Range of hardware interfaces – UART, VGA (4 bit per color), SPI, audio (I2S), Ethernet, LEDs, buttons I/O expansion ports (GPIO) FPGA images for Cortex-M processors Example project for Cortex-M0 DesignStart (processor IP has to be licensed separately) USB connection for downloading FPGA images and program image to micro SD card on board […]

November 15, 2013August 10, 2014 by Jean-Luc Aufranc (CNXSoft) - 3 Comments

Terasic’s Altera DE1-SoC Board Based on Cyclone V Dual Cortex A9 + FPGA SoC Sells for $150 Up

A few months ago, Terasic unveiled its SoCKit powered by Altera Cyclone V dual Cortex A9 + FPGA. They’ve now announced a cheaper version will a less powerful Cyclone V SoC and lower specs (e.g. less RAM, only one sensor, etc…) that sells for as low as $150 for educational or academic purposes, and $199 for the rest of us. Altera DE1-SoC Board specifications: FPGA Device Cyclone V SoC 5CSEMA5F31 Device Dual-core ARM Cortex-A9 (HPS – Hard Processor System) 85K Programmable Logic Elements 4,450 Kbits embedded memory 6 Fractional PLLs 2 Hard Memory Controllers Configuration and Debug Quad Serial Configuration device – EPCQ256 on FPGA (EPCQ = Erasable Programmable Configurable Quad-SPI device) On-Board USB Blaster II (Normal type B USB connector) Memory Device 64MB (32Mx16) SDRAM on FPGA 1GB (2x256Mx16) DDR3 SDRAM on HPS 128MB QSPI Flash on HPS (QSPI Flash does not come pre-installed out of factory) Micro SD […]