Category: Broadcom BCMxxxx

Posted on by Jean-Luc Aufranc (CNXSoft) - 16 Comments on Raspberry Pi Club Battery / UPS Kit Assembly Guide and Review

Raspberry Pi Club Battery / UPS Kit Assembly Guide and Review

A couple of months ago, I wrote about a Raspberry Pi battery kit with a 3,800 mAh battery, a battery control board, an acrylic enclosure, and an heatsink + fan set that I found on DealExtreme for about $22. I decided to buy it once I got confirmation the battery was included, and so today I’ll write about my experience assembling the kit, and running it with a Raspberry Pi 2 board. If you are only interested in the “RPi PowerPack” battery control board and battery, you can find them on Banggood for $11.93. Raspberry Pi Club Battery Kit Unboxing DX put all the accessories inside a zip bag, and shipped it in a bubble envelop. It contains a white box with the RPi PowerPack V1.0 battery and battery, several screws, spacers, and bolts sets, a fan with screws, an acrylic case with three layers, an heatsink set with two […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 17 Comments on Raspberry Pi Bootloader License Precludes it to Run on Competing Broadcom BCM283x Boards

Raspberry Pi Bootloader License Precludes it to Run on Competing Broadcom BCM283x Boards

Yesterday I wrote about ArduCAM Raspberry Pi compatible module, that packs most of the features of Raspberry Pi Zero or Pi Compute module into a 24x24mm board, and is based on Broadcom BCM2835 processor. One person also started a thread on Raspberry Pi forums about the tiny module, and one of the Raspberry Pi engineer and forum moderator replied that will would breach the bootloader license. The important part is the sentence highlighted above: This software may only be used for the purpose of developing for, running or using a Raspberry Pi device. ArduCAM module is only Raspberry Pi compatible, so it would indeed breach the license, and you can get into troubles if you planned to use that module in a commercial project, especially in countries where IP protection is taking seriously. This raises a few questions. First why did the Raspberry Pi foundation chose that restrictive license? The […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 10 Comments on ArduCAM has designed a Tiny Coin-Sized Raspberry Pi Compatible Module

ArduCAM has designed a Tiny Coin-Sized Raspberry Pi Compatible Module

Now you can design your own custom hardware and leverage Raspberry Pi software, by integrating Raspberry Pi Compute module (and soon Raspberry Pi 3 Compute module) into your custom designed baseboard. But if you’d like something more compact, and even more compact than a Raspberry Pi Zero or RPi Compute module, ArduCAM has been developing a 24x24mm Raspberry Pi compatible system-on-module powered by Broadcom BCM2835 processor. ArduCAM has also designed a small adapter board “UC-343 Rev. A” for the module with the following specifications: SoC – Broadcom BCM2835 ARM11 Processor @ 700 MHz (or 1GHz?) with Videocore IV GPU System Memory – 256MB/512MB LPDDR2 Storage – micro SD card slot USB – 2x micro USB ports including one for power only Camera – 1x MIPI CSI connector supporting 5MP or 8MP Pi cameras (dual camera support) Expansion – AV output header 16-pin and 8-pin headers (unpopulated) with GPIOs, 2x I2C, […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 9 Comments on $99 MATRIX Creator Raspberry Pi Add-on Board Features Plenty of Sensors, a 2.4 GHz Radio, and More

$99 MATRIX Creator Raspberry Pi Add-on Board Features Plenty of Sensors, a 2.4 GHz Radio, and More

MATRIX Creator is a round-shaped add-on board for Raspberry Pi boards with various sensors, a microphone array, an LED array, a Xilinx FPGA, an Atmel Cortex-M3 MCU, wireless connectivity via Z-Wave, ZigBee, Thread, and NFC, as well as various I/Os…. MATRIX Creator specifications: FPGA – Xilinx Spartan 6 FPGA MCU – Atmel ATSAM3S2C Cortex-M3 MCU Connectivity – ZigBee, Thread, Z-Wave and NFC Sensors – Ultraviolet, pressure, humidity, temperature, 3D accelerometer, 3D gyroscope, 3D magnetometer Audio – 8x MEMs microphone array with Alexa support Expansion – 2x ADC, 17x digital GPIOs, SPI, I2C, UART; 40-pin connector for Raspberry Pi 2/3 Misc – 35x RGBW LEDs array, IR Rx/Tx, infrared ring for the Raspberry Pi NoIR camera I can’t think of the single application that would make use of all features of this board, but the least we can say is that it’s extremely versatile. The developers are providing MATRIX OS based […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 13 Comments on RisingHF IoT Discovery is a LoRaWAN Evaluation Kit for Raspberry Pi

RisingHF IoT Discovery is a LoRaWAN Evaluation Kit for Raspberry Pi

There are many current and upcoming long range low power wireless protocols for the IoT, but this morning I learned that South Korea launched a LoRa network (aka LoRaWAN), after another launch in the Netherlands earlier this year. While there are also some LoRa hobbyist kits such as LoraONE and LoPy being worked on, I decided to look on Aliexpress, but only got two products were listed: a LoRaWAN temperature and humidity sensor, and a LoraWAN USB modem. Both of them are made by a company called RisingHF. Among the products offered by the company, there’s a potentially interesting development kit called RisingHF IoT Discovery with the following components: 1x Raspberry Pi board 1x RHF0M301 LoRa Gateway based on Semtech SX1301 1x RHF4T002  adapter for Raspberry Pi and RHF0M301 1x RHF3M076 LoRaWAN USB AT Modem End point to connect to computer. It operates at 434MHz, 470MHz,868MHz, and 915MHz 3x RHF76-052 […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 1 Comment on Wi-Fi CERTIFIED ac Wave 2 Products Support MU-MIMO, 160 MHz Channels, and More

Wi-Fi CERTIFIED ac Wave 2 Products Support MU-MIMO, 160 MHz Channels, and More

802.11ac WiFi is now found in many routers and devices, and the Wi-Fi alliance has so far certified close to 3,000 “Wi-Fi CERTIFIED ac” products. I understand that certification is not mandatory, but if you want to make sure a device works well, the certification at least means the devices have been tested for interoperability, security and application specific protocols, and found to work in a satisfactory manner. Now the Wi-Fi alliance has announced Wi-Fi CERTIFIED ac Wave 2 certification program with the following new requirements: MU-MIMO (Multi-user Multiple Input Multiple Output) in order to send data to multiple devices at once to improve overall  network efficiency and throughput 160 MHz channels support (not only 80 MHz) potentially doubling transmission speeds Four spatial streams instead of just three spatial streams. Extended 5 GHz channel support by adding more channels in the 5 GHz to reduce interference and congestion. Currently the […]

Posted on by Jean-Luc Aufranc (CNXSoft) - No Comments on Raspberry Pi Zero Based Google’s Project Bloks Aims to Teach Programming to Young Children

Raspberry Pi Zero Based Google’s Project Bloks Aims to Teach Programming to Young Children

Visual programming development tools such as Scratch or Blockly are now becoming more popular to introduce school children to programming, and Google Research is now working on bringing the software visual programming concept to physical blocks “programming” though Project Bloks targeting younger children who may not be able to write or read yet. It might also help older children grasping programming concepts faster than when programming by typing on a keyboard. Project Bloks is comprised of three main hardware components connected together: Pucks – Those are the buttons, dials, switches, and other inputs from the project. Pucks have no active electronics, and even a piece of paper with some conductive ink could be a Puck. Base Boards –  They read a Puck’s instruction through a capacitive sensor, and forward a Puck’s command to the Brain Board.  Each Base Board is also fitted with a haptic motor & LEDs, and can […]

Posted on by Jean-Luc Aufranc (CNXSoft) - 2 Comments on DIY Wireless Window/Glass Mounted Camera Based on Raspberry Pi Zero Board

DIY Wireless Window/Glass Mounted Camera Based on Raspberry Pi Zero Board

A few weeks ago, the Raspberry Pi foundation announced a new version of the Raspberry Pi Zero with a CSI camera connector. Since the solution is quite lightweight, Steven Cassidy had the idea to make a WiFi enabled window camera by soldering a USB WiFi module and fitting the hardware to a plastic part with two suction cups. Once the assembly is done, you can stuck the hardware to a window or glass of your choice in your home, car, aquarium, etc… If you like the concept but would like to have something working out of the box instead of making your own, the Pi Hut has design ZeroView on the same principle, and which will sell for 7 GBP (~$10.3). Jean-Luc Aufranc (CNXSoft)Jean-Luc started CNX Software in 2010 as a part-time endeavor, before quitting his job as a software engineering manager, and starting to write daily news, and reviews […]

Exit mobile version
UP 7000 x86 SBC